NXP Semiconductors MK22F51212 2024.06.02 MK22F51212 Freescale Microcontroller CM4 r0p1 little true true 4 false 8 32 ADC0 Analog-to-Digital Converter ADC 0x0 0x0 0x70 registers n ADC0 39 CFG1 ADC Configuration Register 1 0x8 32 read-write n 0x0 0x0 ADICLK Input Clock Select 0 2 read-write 00 Bus clock #00 01 Alternate clock 2 (ALTCLK2) #01 10 Alternate clock (ALTCLK) #10 11 Asynchronous clock (ADACK) #11 ADIV Clock Divide Select 5 2 read-write 00 The divide ratio is 1 and the clock rate is input clock. #00 01 The divide ratio is 2 and the clock rate is (input clock)/2. #01 10 The divide ratio is 4 and the clock rate is (input clock)/4. #10 11 The divide ratio is 8 and the clock rate is (input clock)/8. #11 ADLPC Low-Power Configuration 7 1 read-write 0 Normal power configuration. #0 1 Low-power configuration. The power is reduced at the expense of maximum clock speed. #1 ADLSMP Sample Time Configuration 4 1 read-write 0 Short sample time. #0 1 Long sample time. #1 MODE Conversion mode selection 2 2 read-write 00 When DIFF=0:It is single-ended 8-bit conversion; when DIFF=1, it is differential 9-bit conversion with 2's complement output. #00 01 When DIFF=0:It is single-ended 12-bit conversion ; when DIFF=1, it is differential 13-bit conversion with 2's complement output. #01 10 When DIFF=0:It is single-ended 10-bit conversion. ; when DIFF=1, it is differential 11-bit conversion with 2's complement output #10 11 When DIFF=0:It is single-ended 16-bit conversion..; when DIFF=1, it is differential 16-bit conversion with 2's complement output #11 CFG2 ADC Configuration Register 2 0xC 32 read-write n 0x0 0x0 ADACKEN Asynchronous Clock Output Enable 3 1 read-write 0 Asynchronous clock output disabled; Asynchronous clock is enabled only if selected by ADICLK and a conversion is active. #0 1 Asynchronous clock and clock output is enabled regardless of the state of the ADC. #1 ADHSC High-Speed Configuration 2 1 read-write 0 Normal conversion sequence selected. #0 1 High-speed conversion sequence selected with 2 additional ADCK cycles to total conversion time. #1 ADLSTS Long Sample Time Select 0 2 read-write 00 Default longest sample time; 20 extra ADCK cycles; 24 ADCK cycles total. #00 01 12 extra ADCK cycles; 16 ADCK cycles total sample time. #01 10 6 extra ADCK cycles; 10 ADCK cycles total sample time. #10 11 2 extra ADCK cycles; 6 ADCK cycles total sample time. #11 MUXSEL ADC Mux Select 4 1 read-write 0 ADxxa channels are selected. #0 1 ADxxb channels are selected. #1 CLM0 ADC Minus-Side General Calibration Value Register 0x6C 32 read-write n 0x0 0x0 CLM0 Calibration Value 0 6 read-write CLM1 ADC Minus-Side General Calibration Value Register 0x68 32 read-write n 0x0 0x0 CLM1 Calibration Value 0 7 read-write CLM2 ADC Minus-Side General Calibration Value Register 0x64 32 read-write n 0x0 0x0 CLM2 Calibration Value 0 8 read-write CLM3 ADC Minus-Side General Calibration Value Register 0x60 32 read-write n 0x0 0x0 CLM3 Calibration Value 0 9 read-write CLM4 ADC Minus-Side General Calibration Value Register 0x5C 32 read-write n 0x0 0x0 CLM4 Calibration Value 0 10 read-write CLMD ADC Minus-Side General Calibration Value Register 0x54 32 read-write n 0x0 0x0 CLMD Calibration Value 0 6 read-write CLMS ADC Minus-Side General Calibration Value Register 0x58 32 read-write n 0x0 0x0 CLMS Calibration Value 0 6 read-write CLP0 ADC Plus-Side General Calibration Value Register 0x4C 32 read-write n 0x0 0x0 CLP0 Calibration Value 0 6 read-write CLP1 ADC Plus-Side General Calibration Value Register 0x48 32 read-write n 0x0 0x0 CLP1 Calibration Value 0 7 read-write CLP2 ADC Plus-Side General Calibration Value Register 0x44 32 read-write n 0x0 0x0 CLP2 Calibration Value 0 8 read-write CLP3 ADC Plus-Side General Calibration Value Register 0x40 32 read-write n 0x0 0x0 CLP3 Calibration Value 0 9 read-write CLP4 ADC Plus-Side General Calibration Value Register 0x3C 32 read-write n 0x0 0x0 CLP4 Calibration Value 0 10 read-write CLPD ADC Plus-Side General Calibration Value Register 0x34 32 read-write n 0x0 0x0 CLPD Calibration Value 0 6 read-write CLPS ADC Plus-Side General Calibration Value Register 0x38 32 read-write n 0x0 0x0 CLPS Calibration Value 0 6 read-write CV1 Compare Value Registers 0x30 32 read-write n 0x0 0x0 CV Compare Value. 0 16 read-write CV2 Compare Value Registers 0x4C 32 read-write n 0x0 0x0 CV Compare Value. 0 16 read-write MG ADC Minus-Side Gain Register 0x30 32 read-write n 0x0 0x0 MG Minus-Side Gain 0 16 read-write OFS ADC Offset Correction Register 0x28 32 read-write n 0x0 0x0 OFS Offset Error Correction Value 0 16 read-write PG ADC Plus-Side Gain Register 0x2C 32 read-write n 0x0 0x0 PG Plus-Side Gain 0 16 read-write RA ADC Data Result Register 0x20 32 read-only n 0x0 0x0 D Data result 0 16 read-only RB ADC Data Result Register 0x34 32 read-only n 0x0 0x0 D Data result 0 16 read-only SC1A ADC Status and Control Registers 1 0x0 32 read-write n 0x0 0x0 ADCH Input channel select 0 5 read-write 00000 When DIFF=0, DADP0 is selected as input; when DIFF=1, DAD0 is selected as input. #00000 00001 When DIFF=0, DADP1 is selected as input; when DIFF=1, DAD1 is selected as input. #00001 00010 When DIFF=0, DADP2 is selected as input; when DIFF=1, DAD2 is selected as input. #00010 00011 When DIFF=0, DADP3 is selected as input; when DIFF=1, DAD3 is selected as input. #00011 00100 When DIFF=0, AD4 is selected as input; when DIFF=1, it is reserved. #00100 00101 When DIFF=0, AD5 is selected as input; when DIFF=1, it is reserved. #00101 00110 When DIFF=0, AD6 is selected as input; when DIFF=1, it is reserved. #00110 00111 When DIFF=0, AD7 is selected as input; when DIFF=1, it is reserved. #00111 01000 When DIFF=0, AD8 is selected as input; when DIFF=1, it is reserved. #01000 01001 When DIFF=0, AD9 is selected as input; when DIFF=1, it is reserved. #01001 01010 When DIFF=0, AD10 is selected as input; when DIFF=1, it is reserved. #01010 01011 When DIFF=0, AD11 is selected as input; when DIFF=1, it is reserved. #01011 01100 When DIFF=0, AD12 is selected as input; when DIFF=1, it is reserved. #01100 01101 When DIFF=0, AD13 is selected as input; when DIFF=1, it is reserved. #01101 01110 When DIFF=0, AD14 is selected as input; when DIFF=1, it is reserved. #01110 01111 When DIFF=0, AD15 is selected as input; when DIFF=1, it is reserved. #01111 10000 When DIFF=0, AD16 is selected as input; when DIFF=1, it is reserved. #10000 10001 When DIFF=0, AD17 is selected as input; when DIFF=1, it is reserved. #10001 10010 When DIFF=0, AD18 is selected as input; when DIFF=1, it is reserved. #10010 10011 When DIFF=0, AD19 is selected as input; when DIFF=1, it is reserved. #10011 10100 When DIFF=0, AD20 is selected as input; when DIFF=1, it is reserved. #10100 10101 When DIFF=0, AD21 is selected as input; when DIFF=1, it is reserved. #10101 10110 When DIFF=0, AD22 is selected as input; when DIFF=1, it is reserved. #10110 10111 When DIFF=0, AD23 is selected as input; when DIFF=1, it is reserved. #10111 11010 When DIFF=0, Temp Sensor (single-ended) is selected as input; when DIFF=1, Temp Sensor (differential) is selected as input. #11010 11011 When DIFF=0, Bandgap (single-ended) is selected as input; when DIFF=1, Bandgap (differential) is selected as input. #11011 11101 When DIFF=0,VREFSH is selected as input; when DIFF=1, -VREFSH (differential) is selected as input. Voltage reference selected is determined by SC2[REFSEL]. #11101 11110 When DIFF=0,VREFSL is selected as input; when DIFF=1, it is reserved. Voltage reference selected is determined by SC2[REFSEL]. #11110 11111 Module is disabled. #11111 AIEN Interrupt Enable 6 1 read-write 0 Conversion complete interrupt is disabled. #0 1 Conversion complete interrupt is enabled. #1 COCO Conversion Complete Flag 7 1 read-only 0 Conversion is not completed. #0 1 Conversion is completed. #1 DIFF Differential Mode Enable 5 1 read-write 0 Single-ended conversions and input channels are selected. #0 1 Differential conversions and input channels are selected. #1 SC1B ADC Status and Control Registers 1 0x4 32 read-write n 0x0 0x0 ADCH Input channel select 0 5 read-write 00000 When DIFF=0, DADP0 is selected as input; when DIFF=1, DAD0 is selected as input. #00000 00001 When DIFF=0, DADP1 is selected as input; when DIFF=1, DAD1 is selected as input. #00001 00010 When DIFF=0, DADP2 is selected as input; when DIFF=1, DAD2 is selected as input. #00010 00011 When DIFF=0, DADP3 is selected as input; when DIFF=1, DAD3 is selected as input. #00011 00100 When DIFF=0, AD4 is selected as input; when DIFF=1, it is reserved. #00100 00101 When DIFF=0, AD5 is selected as input; when DIFF=1, it is reserved. #00101 00110 When DIFF=0, AD6 is selected as input; when DIFF=1, it is reserved. #00110 00111 When DIFF=0, AD7 is selected as input; when DIFF=1, it is reserved. #00111 01000 When DIFF=0, AD8 is selected as input; when DIFF=1, it is reserved. #01000 01001 When DIFF=0, AD9 is selected as input; when DIFF=1, it is reserved. #01001 01010 When DIFF=0, AD10 is selected as input; when DIFF=1, it is reserved. #01010 01011 When DIFF=0, AD11 is selected as input; when DIFF=1, it is reserved. #01011 01100 When DIFF=0, AD12 is selected as input; when DIFF=1, it is reserved. #01100 01101 When DIFF=0, AD13 is selected as input; when DIFF=1, it is reserved. #01101 01110 When DIFF=0, AD14 is selected as input; when DIFF=1, it is reserved. #01110 01111 When DIFF=0, AD15 is selected as input; when DIFF=1, it is reserved. #01111 10000 When DIFF=0, AD16 is selected as input; when DIFF=1, it is reserved. #10000 10001 When DIFF=0, AD17 is selected as input; when DIFF=1, it is reserved. #10001 10010 When DIFF=0, AD18 is selected as input; when DIFF=1, it is reserved. #10010 10011 When DIFF=0, AD19 is selected as input; when DIFF=1, it is reserved. #10011 10100 When DIFF=0, AD20 is selected as input; when DIFF=1, it is reserved. #10100 10101 When DIFF=0, AD21 is selected as input; when DIFF=1, it is reserved. #10101 10110 When DIFF=0, AD22 is selected as input; when DIFF=1, it is reserved. #10110 10111 When DIFF=0, AD23 is selected as input; when DIFF=1, it is reserved. #10111 11010 When DIFF=0, Temp Sensor (single-ended) is selected as input; when DIFF=1, Temp Sensor (differential) is selected as input. #11010 11011 When DIFF=0, Bandgap (single-ended) is selected as input; when DIFF=1, Bandgap (differential) is selected as input. #11011 11101 When DIFF=0,VREFSH is selected as input; when DIFF=1, -VREFSH (differential) is selected as input. Voltage reference selected is determined by SC2[REFSEL]. #11101 11110 When DIFF=0,VREFSL is selected as input; when DIFF=1, it is reserved. Voltage reference selected is determined by SC2[REFSEL]. #11110 11111 Module is disabled. #11111 AIEN Interrupt Enable 6 1 read-write 0 Conversion complete interrupt is disabled. #0 1 Conversion complete interrupt is enabled. #1 COCO Conversion Complete Flag 7 1 read-only 0 Conversion is not completed. #0 1 Conversion is completed. #1 DIFF Differential Mode Enable 5 1 read-write 0 Single-ended conversions and input channels are selected. #0 1 Differential conversions and input channels are selected. #1 SC2 Status and Control Register 2 0x20 32 read-write n 0x0 0x0 ACFE Compare Function Enable 5 1 read-write 0 Compare function disabled. #0 1 Compare function enabled. #1 ACFGT Compare Function Greater Than Enable 4 1 read-write 0 Configures less than threshold, outside range not inclusive and inside range not inclusive; functionality based on the values placed in CV1 and CV2. #0 1 Configures greater than or equal to threshold, outside and inside ranges inclusive; functionality based on the values placed in CV1 and CV2. #1 ACREN Compare Function Range Enable 3 1 read-write 0 Range function disabled. Only CV1 is compared. #0 1 Range function enabled. Both CV1 and CV2 are compared. #1 ADACT Conversion Active 7 1 read-only 0 Conversion not in progress. #0 1 Conversion in progress. #1 ADTRG Conversion Trigger Select 6 1 read-write 0 Software trigger selected. #0 1 Hardware trigger selected. #1 DMAEN DMA Enable 2 1 read-write 0 DMA is disabled. #0 1 DMA is enabled and will assert the ADC DMA request during an ADC conversion complete event noted when any of the SC1n[COCO] flags is asserted. #1 REFSEL Voltage Reference Selection 0 2 read-write 00 Default voltage reference pin pair, that is, external pins VREFH and VREFL #00 01 Alternate reference pair, that is, VALTH and VALTL . This pair may be additional external pins or internal sources depending on the MCU configuration. See the chip configuration information for details specific to this MCU #01 SC3 Status and Control Register 3 0x24 32 read-write n 0x0 0x0 ADCO Continuous Conversion Enable 3 1 read-write 0 One conversion or one set of conversions if the hardware average function is enabled, that is, AVGE=1, after initiating a conversion. #0 1 Continuous conversions or sets of conversions if the hardware average function is enabled, that is, AVGE=1, after initiating a conversion. #1 AVGE Hardware Average Enable 2 1 read-write 0 Hardware average function disabled. #0 1 Hardware average function enabled. #1 AVGS Hardware Average Select 0 2 read-write 00 4 samples averaged. #00 01 8 samples averaged. #01 10 16 samples averaged. #10 11 32 samples averaged. #11 CAL Calibration 7 1 read-write CALF Calibration Failed Flag 6 1 read-write 0 Calibration completed normally. #0 1 Calibration failed. ADC accuracy specifications are not guaranteed. #1 ADC1 Analog-to-Digital Converter ADC 0x0 0x0 0x70 registers n ADC1 73 CFG1 ADC Configuration Register 1 0x8 32 read-write n 0x0 0x0 ADICLK Input Clock Select 0 2 read-write 00 Bus clock #00 01 Alternate clock 2 (ALTCLK2) #01 10 Alternate clock (ALTCLK) #10 11 Asynchronous clock (ADACK) #11 ADIV Clock Divide Select 5 2 read-write 00 The divide ratio is 1 and the clock rate is input clock. #00 01 The divide ratio is 2 and the clock rate is (input clock)/2. #01 10 The divide ratio is 4 and the clock rate is (input clock)/4. #10 11 The divide ratio is 8 and the clock rate is (input clock)/8. #11 ADLPC Low-Power Configuration 7 1 read-write 0 Normal power configuration. #0 1 Low-power configuration. The power is reduced at the expense of maximum clock speed. #1 ADLSMP Sample Time Configuration 4 1 read-write 0 Short sample time. #0 1 Long sample time. #1 MODE Conversion mode selection 2 2 read-write 00 When DIFF=0:It is single-ended 8-bit conversion; when DIFF=1, it is differential 9-bit conversion with 2's complement output. #00 01 When DIFF=0:It is single-ended 12-bit conversion ; when DIFF=1, it is differential 13-bit conversion with 2's complement output. #01 10 When DIFF=0:It is single-ended 10-bit conversion. ; when DIFF=1, it is differential 11-bit conversion with 2's complement output #10 11 When DIFF=0:It is single-ended 16-bit conversion..; when DIFF=1, it is differential 16-bit conversion with 2's complement output #11 CFG2 ADC Configuration Register 2 0xC 32 read-write n 0x0 0x0 ADACKEN Asynchronous Clock Output Enable 3 1 read-write 0 Asynchronous clock output disabled; Asynchronous clock is enabled only if selected by ADICLK and a conversion is active. #0 1 Asynchronous clock and clock output is enabled regardless of the state of the ADC. #1 ADHSC High-Speed Configuration 2 1 read-write 0 Normal conversion sequence selected. #0 1 High-speed conversion sequence selected with 2 additional ADCK cycles to total conversion time. #1 ADLSTS Long Sample Time Select 0 2 read-write 00 Default longest sample time; 20 extra ADCK cycles; 24 ADCK cycles total. #00 01 12 extra ADCK cycles; 16 ADCK cycles total sample time. #01 10 6 extra ADCK cycles; 10 ADCK cycles total sample time. #10 11 2 extra ADCK cycles; 6 ADCK cycles total sample time. #11 MUXSEL ADC Mux Select 4 1 read-write 0 ADxxa channels are selected. #0 1 ADxxb channels are selected. #1 CLM0 ADC Minus-Side General Calibration Value Register 0x6C 32 read-write n 0x0 0x0 CLM0 Calibration Value 0 6 read-write CLM1 ADC Minus-Side General Calibration Value Register 0x68 32 read-write n 0x0 0x0 CLM1 Calibration Value 0 7 read-write CLM2 ADC Minus-Side General Calibration Value Register 0x64 32 read-write n 0x0 0x0 CLM2 Calibration Value 0 8 read-write CLM3 ADC Minus-Side General Calibration Value Register 0x60 32 read-write n 0x0 0x0 CLM3 Calibration Value 0 9 read-write CLM4 ADC Minus-Side General Calibration Value Register 0x5C 32 read-write n 0x0 0x0 CLM4 Calibration Value 0 10 read-write CLMD ADC Minus-Side General Calibration Value Register 0x54 32 read-write n 0x0 0x0 CLMD Calibration Value 0 6 read-write CLMS ADC Minus-Side General Calibration Value Register 0x58 32 read-write n 0x0 0x0 CLMS Calibration Value 0 6 read-write CLP0 ADC Plus-Side General Calibration Value Register 0x4C 32 read-write n 0x0 0x0 CLP0 Calibration Value 0 6 read-write CLP1 ADC Plus-Side General Calibration Value Register 0x48 32 read-write n 0x0 0x0 CLP1 Calibration Value 0 7 read-write CLP2 ADC Plus-Side General Calibration Value Register 0x44 32 read-write n 0x0 0x0 CLP2 Calibration Value 0 8 read-write CLP3 ADC Plus-Side General Calibration Value Register 0x40 32 read-write n 0x0 0x0 CLP3 Calibration Value 0 9 read-write CLP4 ADC Plus-Side General Calibration Value Register 0x3C 32 read-write n 0x0 0x0 CLP4 Calibration Value 0 10 read-write CLPD ADC Plus-Side General Calibration Value Register 0x34 32 read-write n 0x0 0x0 CLPD Calibration Value 0 6 read-write CLPS ADC Plus-Side General Calibration Value Register 0x38 32 read-write n 0x0 0x0 CLPS Calibration Value 0 6 read-write CV1 Compare Value Registers 0x30 32 read-write n 0x0 0x0 CV Compare Value. 0 16 read-write CV2 Compare Value Registers 0x4C 32 read-write n 0x0 0x0 CV Compare Value. 0 16 read-write MG ADC Minus-Side Gain Register 0x30 32 read-write n 0x0 0x0 MG Minus-Side Gain 0 16 read-write OFS ADC Offset Correction Register 0x28 32 read-write n 0x0 0x0 OFS Offset Error Correction Value 0 16 read-write PG ADC Plus-Side Gain Register 0x2C 32 read-write n 0x0 0x0 PG Plus-Side Gain 0 16 read-write RA ADC Data Result Register 0x20 32 read-only n 0x0 0x0 D Data result 0 16 read-only RB ADC Data Result Register 0x34 32 read-only n 0x0 0x0 D Data result 0 16 read-only SC1A ADC Status and Control Registers 1 0x0 32 read-write n 0x0 0x0 ADCH Input channel select 0 5 read-write 00000 When DIFF=0, DADP0 is selected as input; when DIFF=1, DAD0 is selected as input. #00000 00001 When DIFF=0, DADP1 is selected as input; when DIFF=1, DAD1 is selected as input. #00001 00010 When DIFF=0, DADP2 is selected as input; when DIFF=1, DAD2 is selected as input. #00010 00011 When DIFF=0, DADP3 is selected as input; when DIFF=1, DAD3 is selected as input. #00011 00100 When DIFF=0, AD4 is selected as input; when DIFF=1, it is reserved. #00100 00101 When DIFF=0, AD5 is selected as input; when DIFF=1, it is reserved. #00101 00110 When DIFF=0, AD6 is selected as input; when DIFF=1, it is reserved. #00110 00111 When DIFF=0, AD7 is selected as input; when DIFF=1, it is reserved. #00111 01000 When DIFF=0, AD8 is selected as input; when DIFF=1, it is reserved. #01000 01001 When DIFF=0, AD9 is selected as input; when DIFF=1, it is reserved. #01001 01010 When DIFF=0, AD10 is selected as input; when DIFF=1, it is reserved. #01010 01011 When DIFF=0, AD11 is selected as input; when DIFF=1, it is reserved. #01011 01100 When DIFF=0, AD12 is selected as input; when DIFF=1, it is reserved. #01100 01101 When DIFF=0, AD13 is selected as input; when DIFF=1, it is reserved. #01101 01110 When DIFF=0, AD14 is selected as input; when DIFF=1, it is reserved. #01110 01111 When DIFF=0, AD15 is selected as input; when DIFF=1, it is reserved. #01111 10000 When DIFF=0, AD16 is selected as input; when DIFF=1, it is reserved. #10000 10001 When DIFF=0, AD17 is selected as input; when DIFF=1, it is reserved. #10001 10010 When DIFF=0, AD18 is selected as input; when DIFF=1, it is reserved. #10010 10011 When DIFF=0, AD19 is selected as input; when DIFF=1, it is reserved. #10011 10100 When DIFF=0, AD20 is selected as input; when DIFF=1, it is reserved. #10100 10101 When DIFF=0, AD21 is selected as input; when DIFF=1, it is reserved. #10101 10110 When DIFF=0, AD22 is selected as input; when DIFF=1, it is reserved. #10110 10111 When DIFF=0, AD23 is selected as input; when DIFF=1, it is reserved. #10111 11010 When DIFF=0, Temp Sensor (single-ended) is selected as input; when DIFF=1, Temp Sensor (differential) is selected as input. #11010 11011 When DIFF=0, Bandgap (single-ended) is selected as input; when DIFF=1, Bandgap (differential) is selected as input. #11011 11101 When DIFF=0,VREFSH is selected as input; when DIFF=1, -VREFSH (differential) is selected as input. Voltage reference selected is determined by SC2[REFSEL]. #11101 11110 When DIFF=0,VREFSL is selected as input; when DIFF=1, it is reserved. Voltage reference selected is determined by SC2[REFSEL]. #11110 11111 Module is disabled. #11111 AIEN Interrupt Enable 6 1 read-write 0 Conversion complete interrupt is disabled. #0 1 Conversion complete interrupt is enabled. #1 COCO Conversion Complete Flag 7 1 read-only 0 Conversion is not completed. #0 1 Conversion is completed. #1 DIFF Differential Mode Enable 5 1 read-write 0 Single-ended conversions and input channels are selected. #0 1 Differential conversions and input channels are selected. #1 SC1B ADC Status and Control Registers 1 0x4 32 read-write n 0x0 0x0 ADCH Input channel select 0 5 read-write 00000 When DIFF=0, DADP0 is selected as input; when DIFF=1, DAD0 is selected as input. #00000 00001 When DIFF=0, DADP1 is selected as input; when DIFF=1, DAD1 is selected as input. #00001 00010 When DIFF=0, DADP2 is selected as input; when DIFF=1, DAD2 is selected as input. #00010 00011 When DIFF=0, DADP3 is selected as input; when DIFF=1, DAD3 is selected as input. #00011 00100 When DIFF=0, AD4 is selected as input; when DIFF=1, it is reserved. #00100 00101 When DIFF=0, AD5 is selected as input; when DIFF=1, it is reserved. #00101 00110 When DIFF=0, AD6 is selected as input; when DIFF=1, it is reserved. #00110 00111 When DIFF=0, AD7 is selected as input; when DIFF=1, it is reserved. #00111 01000 When DIFF=0, AD8 is selected as input; when DIFF=1, it is reserved. #01000 01001 When DIFF=0, AD9 is selected as input; when DIFF=1, it is reserved. #01001 01010 When DIFF=0, AD10 is selected as input; when DIFF=1, it is reserved. #01010 01011 When DIFF=0, AD11 is selected as input; when DIFF=1, it is reserved. #01011 01100 When DIFF=0, AD12 is selected as input; when DIFF=1, it is reserved. #01100 01101 When DIFF=0, AD13 is selected as input; when DIFF=1, it is reserved. #01101 01110 When DIFF=0, AD14 is selected as input; when DIFF=1, it is reserved. #01110 01111 When DIFF=0, AD15 is selected as input; when DIFF=1, it is reserved. #01111 10000 When DIFF=0, AD16 is selected as input; when DIFF=1, it is reserved. #10000 10001 When DIFF=0, AD17 is selected as input; when DIFF=1, it is reserved. #10001 10010 When DIFF=0, AD18 is selected as input; when DIFF=1, it is reserved. #10010 10011 When DIFF=0, AD19 is selected as input; when DIFF=1, it is reserved. #10011 10100 When DIFF=0, AD20 is selected as input; when DIFF=1, it is reserved. #10100 10101 When DIFF=0, AD21 is selected as input; when DIFF=1, it is reserved. #10101 10110 When DIFF=0, AD22 is selected as input; when DIFF=1, it is reserved. #10110 10111 When DIFF=0, AD23 is selected as input; when DIFF=1, it is reserved. #10111 11010 When DIFF=0, Temp Sensor (single-ended) is selected as input; when DIFF=1, Temp Sensor (differential) is selected as input. #11010 11011 When DIFF=0, Bandgap (single-ended) is selected as input; when DIFF=1, Bandgap (differential) is selected as input. #11011 11101 When DIFF=0,VREFSH is selected as input; when DIFF=1, -VREFSH (differential) is selected as input. Voltage reference selected is determined by SC2[REFSEL]. #11101 11110 When DIFF=0,VREFSL is selected as input; when DIFF=1, it is reserved. Voltage reference selected is determined by SC2[REFSEL]. #11110 11111 Module is disabled. #11111 AIEN Interrupt Enable 6 1 read-write 0 Conversion complete interrupt is disabled. #0 1 Conversion complete interrupt is enabled. #1 COCO Conversion Complete Flag 7 1 read-only 0 Conversion is not completed. #0 1 Conversion is completed. #1 DIFF Differential Mode Enable 5 1 read-write 0 Single-ended conversions and input channels are selected. #0 1 Differential conversions and input channels are selected. #1 SC2 Status and Control Register 2 0x20 32 read-write n 0x0 0x0 ACFE Compare Function Enable 5 1 read-write 0 Compare function disabled. #0 1 Compare function enabled. #1 ACFGT Compare Function Greater Than Enable 4 1 read-write 0 Configures less than threshold, outside range not inclusive and inside range not inclusive; functionality based on the values placed in CV1 and CV2. #0 1 Configures greater than or equal to threshold, outside and inside ranges inclusive; functionality based on the values placed in CV1 and CV2. #1 ACREN Compare Function Range Enable 3 1 read-write 0 Range function disabled. Only CV1 is compared. #0 1 Range function enabled. Both CV1 and CV2 are compared. #1 ADACT Conversion Active 7 1 read-only 0 Conversion not in progress. #0 1 Conversion in progress. #1 ADTRG Conversion Trigger Select 6 1 read-write 0 Software trigger selected. #0 1 Hardware trigger selected. #1 DMAEN DMA Enable 2 1 read-write 0 DMA is disabled. #0 1 DMA is enabled and will assert the ADC DMA request during an ADC conversion complete event noted when any of the SC1n[COCO] flags is asserted. #1 REFSEL Voltage Reference Selection 0 2 read-write 00 Default voltage reference pin pair, that is, external pins VREFH and VREFL #00 01 Alternate reference pair, that is, VALTH and VALTL . This pair may be additional external pins or internal sources depending on the MCU configuration. See the chip configuration information for details specific to this MCU #01 SC3 Status and Control Register 3 0x24 32 read-write n 0x0 0x0 ADCO Continuous Conversion Enable 3 1 read-write 0 One conversion or one set of conversions if the hardware average function is enabled, that is, AVGE=1, after initiating a conversion. #0 1 Continuous conversions or sets of conversions if the hardware average function is enabled, that is, AVGE=1, after initiating a conversion. #1 AVGE Hardware Average Enable 2 1 read-write 0 Hardware average function disabled. #0 1 Hardware average function enabled. #1 AVGS Hardware Average Select 0 2 read-write 00 4 samples averaged. #00 01 8 samples averaged. #01 10 16 samples averaged. #10 11 32 samples averaged. #11 CAL Calibration 7 1 read-write CALF Calibration Failed Flag 6 1 read-write 0 Calibration completed normally. #0 1 Calibration failed. ADC accuracy specifications are not guaranteed. #1 CMP0 High-Speed Comparator (CMP), Voltage Reference (VREF) Digital-to-Analog Converter (DAC), and Analog Mux (ANMUX) CMP 0x0 0x0 0x6 registers n CMP0 40 CR0 CMP Control Register 0 0x0 8 read-write n 0x0 0x0 FILTER_CNT Filter Sample Count 4 3 read-write 000 Filter is disabled. If SE = 1, then COUT is a logic 0. This is not a legal state, and is not recommended. If SE = 0, COUT = COUTA. #000 001 One sample must agree. The comparator output is simply sampled. #001 010 2 consecutive samples must agree. #010 011 3 consecutive samples must agree. #011 100 4 consecutive samples must agree. #100 101 5 consecutive samples must agree. #101 110 6 consecutive samples must agree. #110 111 7 consecutive samples must agree. #111 HYSTCTR Comparator hard block hysteresis control 0 2 read-write 00 Level 0 #00 01 Level 1 #01 10 Level 2 #10 11 Level 3 #11 CR1 CMP Control Register 1 0x1 8 read-write n 0x0 0x0 COS Comparator Output Select 2 1 read-write 0 Set the filtered comparator output (CMPO) to equal COUT. #0 1 Set the unfiltered comparator output (CMPO) to equal COUTA. #1 EN Comparator Module Enable 0 1 read-write 0 Analog Comparator is disabled. #0 1 Analog Comparator is enabled. #1 INV Comparator INVERT 3 1 read-write 0 Does not invert the comparator output. #0 1 Inverts the comparator output. #1 OPE Comparator Output Pin Enable 1 1 read-write 0 CMPO is not available on the associated CMPO output pin. If the comparator does not own the pin, this field has no effect. #0 1 CMPO is available on the associated CMPO output pin. The comparator output (CMPO) is driven out on the associated CMPO output pin if the comparator owns the pin. If the comparator does not own the field, this bit has no effect. #1 PMODE Power Mode Select 4 1 read-write 0 Low-Speed (LS) Comparison mode selected. In this mode, CMP has slower output propagation delay and lower current consumption. #0 1 High-Speed (HS) Comparison mode selected. In this mode, CMP has faster output propagation delay and higher current consumption. #1 SE Sample Enable 7 1 read-write 0 Sampling mode is not selected. #0 1 Sampling mode is selected. #1 TRIGM Trigger Mode Enable 5 1 read-write 0 Trigger mode is disabled. #0 1 Trigger mode is enabled. #1 WE Windowing Enable 6 1 read-write 0 Windowing mode is not selected. #0 1 Windowing mode is selected. #1 DACCR DAC Control Register 0x4 8 read-write n 0x0 0x0 DACEN DAC Enable 7 1 read-write 0 DAC is disabled. #0 1 DAC is enabled. #1 VOSEL DAC Output Voltage Select 0 6 read-write VRSEL Supply Voltage Reference Source Select 6 1 read-write 0 V is selected as resistor ladder network supply reference V. in1 in #0 1 V is selected as resistor ladder network supply reference V. in2 in #1 FPR CMP Filter Period Register 0x2 8 read-write n 0x0 0x0 FILT_PER Filter Sample Period 0 8 read-write MUXCR MUX Control Register 0x5 8 read-write n 0x0 0x0 MSEL Minus Input Mux Control 0 3 read-write 000 IN0 #000 001 IN1 #001 010 IN2 #010 011 IN3 #011 100 IN4 #100 101 IN5 #101 110 IN6 #110 111 IN7 #111 PSEL Plus Input Mux Control 3 3 read-write 000 IN0 #000 001 IN1 #001 010 IN2 #010 011 IN3 #011 100 IN4 #100 101 IN5 #101 110 IN6 #110 111 IN7 #111 SCR CMP Status and Control Register 0x3 8 read-write n 0x0 0x0 CFF Analog Comparator Flag Falling 1 1 read-write 0 Falling-edge on COUT has not been detected. #0 1 Falling-edge on COUT has occurred. #1 CFR Analog Comparator Flag Rising 2 1 read-write 0 Rising-edge on COUT has not been detected. #0 1 Rising-edge on COUT has occurred. #1 COUT Analog Comparator Output 0 1 read-only DMAEN DMA Enable Control 6 1 read-write 0 DMA is disabled. #0 1 DMA is enabled. #1 IEF Comparator Interrupt Enable Falling 3 1 read-write 0 Interrupt is disabled. #0 1 Interrupt is enabled. #1 IER Comparator Interrupt Enable Rising 4 1 read-write 0 Interrupt is disabled. #0 1 Interrupt is enabled. #1 CMP1 High-Speed Comparator (CMP), Voltage Reference (VREF) Digital-to-Analog Converter (DAC), and Analog Mux (ANMUX) CMP 0x0 0x0 0x6 registers n CMP1 41 CR0 CMP Control Register 0 0x0 8 read-write n 0x0 0x0 FILTER_CNT Filter Sample Count 4 3 read-write 000 Filter is disabled. If SE = 1, then COUT is a logic 0. This is not a legal state, and is not recommended. If SE = 0, COUT = COUTA. #000 001 One sample must agree. The comparator output is simply sampled. #001 010 2 consecutive samples must agree. #010 011 3 consecutive samples must agree. #011 100 4 consecutive samples must agree. #100 101 5 consecutive samples must agree. #101 110 6 consecutive samples must agree. #110 111 7 consecutive samples must agree. #111 HYSTCTR Comparator hard block hysteresis control 0 2 read-write 00 Level 0 #00 01 Level 1 #01 10 Level 2 #10 11 Level 3 #11 CR1 CMP Control Register 1 0x1 8 read-write n 0x0 0x0 COS Comparator Output Select 2 1 read-write 0 Set the filtered comparator output (CMPO) to equal COUT. #0 1 Set the unfiltered comparator output (CMPO) to equal COUTA. #1 EN Comparator Module Enable 0 1 read-write 0 Analog Comparator is disabled. #0 1 Analog Comparator is enabled. #1 INV Comparator INVERT 3 1 read-write 0 Does not invert the comparator output. #0 1 Inverts the comparator output. #1 OPE Comparator Output Pin Enable 1 1 read-write 0 CMPO is not available on the associated CMPO output pin. If the comparator does not own the pin, this field has no effect. #0 1 CMPO is available on the associated CMPO output pin. The comparator output (CMPO) is driven out on the associated CMPO output pin if the comparator owns the pin. If the comparator does not own the field, this bit has no effect. #1 PMODE Power Mode Select 4 1 read-write 0 Low-Speed (LS) Comparison mode selected. In this mode, CMP has slower output propagation delay and lower current consumption. #0 1 High-Speed (HS) Comparison mode selected. In this mode, CMP has faster output propagation delay and higher current consumption. #1 SE Sample Enable 7 1 read-write 0 Sampling mode is not selected. #0 1 Sampling mode is selected. #1 TRIGM Trigger Mode Enable 5 1 read-write 0 Trigger mode is disabled. #0 1 Trigger mode is enabled. #1 WE Windowing Enable 6 1 read-write 0 Windowing mode is not selected. #0 1 Windowing mode is selected. #1 DACCR DAC Control Register 0x4 8 read-write n 0x0 0x0 DACEN DAC Enable 7 1 read-write 0 DAC is disabled. #0 1 DAC is enabled. #1 VOSEL DAC Output Voltage Select 0 6 read-write VRSEL Supply Voltage Reference Source Select 6 1 read-write 0 V is selected as resistor ladder network supply reference V. in1 in #0 1 V is selected as resistor ladder network supply reference V. in2 in #1 FPR CMP Filter Period Register 0x2 8 read-write n 0x0 0x0 FILT_PER Filter Sample Period 0 8 read-write MUXCR MUX Control Register 0x5 8 read-write n 0x0 0x0 MSEL Minus Input Mux Control 0 3 read-write 000 IN0 #000 001 IN1 #001 010 IN2 #010 011 IN3 #011 100 IN4 #100 101 IN5 #101 110 IN6 #110 111 IN7 #111 PSEL Plus Input Mux Control 3 3 read-write 000 IN0 #000 001 IN1 #001 010 IN2 #010 011 IN3 #011 100 IN4 #100 101 IN5 #101 110 IN6 #110 111 IN7 #111 SCR CMP Status and Control Register 0x3 8 read-write n 0x0 0x0 CFF Analog Comparator Flag Falling 1 1 read-write 0 Falling-edge on COUT has not been detected. #0 1 Falling-edge on COUT has occurred. #1 CFR Analog Comparator Flag Rising 2 1 read-write 0 Rising-edge on COUT has not been detected. #0 1 Rising-edge on COUT has occurred. #1 COUT Analog Comparator Output 0 1 read-only DMAEN DMA Enable Control 6 1 read-write 0 DMA is disabled. #0 1 DMA is enabled. #1 IEF Comparator Interrupt Enable Falling 3 1 read-write 0 Interrupt is disabled. #0 1 Interrupt is enabled. #1 IER Comparator Interrupt Enable Rising 4 1 read-write 0 Interrupt is disabled. #0 1 Interrupt is enabled. #1 CRC Cyclic Redundancy Check CRC 0x0 0x0 0xC registers n CTRL CRC Control register 0x8 32 read-write n 0x0 0x0 FXOR Complement Read Of CRC Data Register 26 1 read-write 0 No XOR on reading. #0 1 Invert or complement the read value of the CRC Data register. #1 TCRC Width of CRC protocol. 24 1 read-write 0 16-bit CRC protocol. #0 1 32-bit CRC protocol. #1 TOT Type Of Transpose For Writes 30 2 read-write 00 No transposition. #00 01 Bits in bytes are transposed; bytes are not transposed. #01 10 Both bits in bytes and bytes are transposed. #10 11 Only bytes are transposed; no bits in a byte are transposed. #11 TOTR Type Of Transpose For Read 28 2 read-write 00 No transposition. #00 01 Bits in bytes are transposed; bytes are not transposed. #01 10 Both bits in bytes and bytes are transposed. #10 11 Only bytes are transposed; no bits in a byte are transposed. #11 WAS Write CRC Data Register As Seed 25 1 read-write 0 Writes to the CRC data register are data values. #0 1 Writes to the CRC data register are seed values. #1 CTRLHU CRC_CTRLHU register. 0xB 8 read-write n 0x0 0x0 FXOR no description available 2 1 read-write 0 No XOR on reading. #0 1 Invert or complement the read value of CRC data register. #1 TCRC no description available 0 1 read-write 0 16-bit CRC protocol. #0 1 32-bit CRC protocol. #1 TOT no description available 6 2 read-write 00 No Transposition. #00 01 Bits in bytes are transposed, bytes are not transposed. #01 10 Both bits in bytes and bytes are transposed. #10 11 Only bytes are transposed; no bits in a byte are transposed. #11 TOTR no description available 4 2 read-write 00 No Transposition. #00 01 Bits in bytes are transposed, bytes are not transposed. #01 10 Both bits in bytes and bytes are transposed. #10 11 Only bytes are transposed; no bits in a byte are transposed. #11 WAS no description available 1 1 read-write 0 Writes to CRC data register are data values. #0 1 Writes to CRC data reguster are seed values. #1 DATA CRC Data register CRC 0x0 32 read-write n 0x0 0x0 HL CRC High Lower Byte 16 8 read-write HU CRC High Upper Byte 24 8 read-write LL CRC Low Lower Byte 0 8 read-write LU CRC Low Upper Byte 8 8 read-write DATAH CRC_DATAH register. CRC 0x2 16 read-write n 0x0 0x0 DATAH DATAH stores the high 16 bits of the 16/32 bit CRC 0 16 read-write DATAHL CRC_DATAHL register. CRC 0x2 8 read-write n 0x0 0x0 DATAHL DATAHL stores the third 8 bits of the 32 bit CRC 0 8 read-write DATAHU CRC_DATAHU register. 0x3 8 read-write n 0x0 0x0 DATAHU DATAHU stores the fourth 8 bits of the 32 bit CRC 0 8 read-write DATAL CRC_DATAL register. CRC 0x0 16 read-write n 0x0 0x0 DATAL DATAL stores the lower 16 bits of the 16/32 bit CRC 0 16 read-write DATALL CRC_DATALL register. CRC 0x0 8 read-write n 0x0 0x0 DATALL CRCLL stores the first 8 bits of the 32 bit DATA 0 8 read-write DATALU CRC_DATALU register. 0x1 8 read-write n 0x0 0x0 DATALU DATALL stores the second 8 bits of the 32 bit CRC 0 8 read-write GPOLY CRC Polynomial register CRC 0x4 32 read-write n 0x0 0x0 HIGH High Polynominal Half-word 16 16 read-write LOW Low Polynominal Half-word 0 16 read-write GPOLYH CRC_GPOLYH register. CRC 0x6 16 read-write n 0x0 0x0 GPOLYH POLYH stores the high 16 bits of the 16/32 bit CRC polynomial value 0 16 read-write GPOLYHL CRC_GPOLYHL register. CRC 0x6 8 read-write n 0x0 0x0 GPOLYHL POLYHL stores the third 8 bits of the 32 bit CRC 0 8 read-write GPOLYHU CRC_GPOLYHU register. 0x7 8 read-write n 0x0 0x0 GPOLYHU POLYHU stores the fourth 8 bits of the 32 bit CRC 0 8 read-write GPOLYL CRC_GPOLYL register. CRC 0x4 16 read-write n 0x0 0x0 GPOLYL POLYL stores the lower 16 bits of the 16/32 bit CRC polynomial value 0 16 read-write GPOLYLL CRC_GPOLYLL register. CRC 0x4 8 read-write n 0x0 0x0 GPOLYLL POLYLL stores the first 8 bits of the 32 bit CRC 0 8 read-write GPOLYLU CRC_GPOLYLU register. 0x5 8 read-write n 0x0 0x0 GPOLYLU POLYLL stores the second 8 bits of the 32 bit CRC 0 8 read-write DAC0 12-Bit Digital-to-Analog Converter DAC 0x0 0x0 0x24 registers n DAC0 56 C0 DAC Control Register 0x21 8 read-write n 0x0 0x0 DACBBIEN DAC Buffer Read Pointer Bottom Flag Interrupt Enable 0 1 read-write 0 The DAC buffer read pointer bottom flag interrupt is disabled. #0 1 The DAC buffer read pointer bottom flag interrupt is enabled. #1 DACBTIEN DAC Buffer Read Pointer Top Flag Interrupt Enable 1 1 read-write 0 The DAC buffer read pointer top flag interrupt is disabled. #0 1 The DAC buffer read pointer top flag interrupt is enabled. #1 DACBWIEN DAC Buffer Watermark Interrupt Enable 2 1 read-write 0 The DAC buffer watermark interrupt is disabled. #0 1 The DAC buffer watermark interrupt is enabled. #1 DACEN DAC Enable 7 1 read-write 0 The DAC system is disabled. #0 1 The DAC system is enabled. #1 DACRFS DAC Reference Select 6 1 read-write 0 The DAC selects DACREF_1 as the reference voltage. #0 1 The DAC selects DACREF_2 as the reference voltage. #1 DACSWTRG DAC Software Trigger 4 1 write-only 0 The DAC soft trigger is not valid. #0 1 The DAC soft trigger is valid. #1 DACTRGSEL DAC Trigger Select 5 1 read-write 0 The DAC hardware trigger is selected. #0 1 The DAC software trigger is selected. #1 LPEN DAC Low Power Control 3 1 read-write 0 High-Power mode #0 1 Low-Power mode #1 C1 DAC Control Register 1 0x22 8 read-write n 0x0 0x0 DACBFEN DAC Buffer Enable 0 1 read-write 0 Buffer read pointer is disabled. The converted data is always the first word of the buffer. #0 1 Buffer read pointer is enabled. The converted data is the word that the read pointer points to. It means converted data can be from any word of the buffer. #1 DACBFMD DAC Buffer Work Mode Select 1 2 read-write 00 Normal mode #00 01 Swing mode #01 10 One-Time Scan mode #10 11 FIFO mode #11 DACBFWM DAC Buffer Watermark Select 3 2 read-write 00 In normal mode, 1 word . In FIFO mode, 2 or less than 2 data remaining in FIFO will set watermark status bit. #00 01 In normal mode, 2 words . In FIFO mode, Max/4 or less than Max/4 data remaining in FIFO will set watermark status bit. #01 10 In normal mode, 3 words . In FIFO mode, Max/2 or less than Max/2 data remaining in FIFO will set watermark status bit. #10 11 In normal mode, 4 words . In FIFO mode, Max-2 or less than Max-2 data remaining in FIFO will set watermark status bit. #11 DMAEN DMA Enable Select 7 1 read-write 0 DMA is disabled. #0 1 DMA is enabled. When DMA is enabled, the DMA request will be generated by original interrupts. The interrupts will not be presented on this module at the same time. #1 C2 DAC Control Register 2 0x23 8 read-write n 0x0 0x0 DACBFRP DAC Buffer Read Pointer 4 4 read-write DACBFUP DAC Buffer Upper Limit 0 4 read-write DAT0H DAC Data High Register 0x2 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT0L DAC Data Low Register 0x0 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT10H DAC Data High Register 0x7A 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT10L DAC Data Low Register 0x6E 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT11H DAC Data High Register 0x91 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT11L DAC Data Low Register 0x84 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT12H DAC Data High Register 0xAA 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT12L DAC Data Low Register 0x9C 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT13H DAC Data High Register 0xC5 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT13L DAC Data Low Register 0xB6 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT14H DAC Data High Register 0xE2 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT14L DAC Data Low Register 0xD2 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT15H DAC Data High Register 0x101 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT15L DAC Data Low Register 0xF0 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT1H DAC Data High Register 0x5 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT1L DAC Data Low Register 0x2 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT2H DAC Data High Register 0xA 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT2L DAC Data Low Register 0x6 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT3H DAC Data High Register 0x11 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT3L DAC Data Low Register 0xC 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT4H DAC Data High Register 0x1A 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT4L DAC Data Low Register 0x14 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT5H DAC Data High Register 0x25 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT5L DAC Data Low Register 0x1E 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT6H DAC Data High Register 0x32 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT6L DAC Data Low Register 0x2A 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT7H DAC Data High Register 0x41 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT7L DAC Data Low Register 0x38 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT8H DAC Data High Register 0x52 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT8L DAC Data Low Register 0x48 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT9H DAC Data High Register 0x65 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT9L DAC Data Low Register 0x5A 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write SR DAC Status Register 0x20 8 read-write n 0x0 0x0 DACBFRPBF DAC Buffer Read Pointer Bottom Position Flag 0 1 read-write 0 The DAC buffer read pointer is not equal to C2[DACBFUP]. #0 1 The DAC buffer read pointer is equal to C2[DACBFUP]. #1 DACBFRPTF DAC Buffer Read Pointer Top Position Flag 1 1 read-write 0 The DAC buffer read pointer is not zero. #0 1 The DAC buffer read pointer is zero. #1 DACBFWMF DAC Buffer Watermark Flag 2 1 read-write 0 The DAC buffer read pointer has not reached the watermark level. #0 1 The DAC buffer read pointer has reached the watermark level. #1 DAC1 12-Bit Digital-to-Analog Converter DAC 0x0 0x0 0x24 registers n DAC1 72 C0 DAC Control Register 0x21 8 read-write n 0x0 0x0 DACBBIEN DAC Buffer Read Pointer Bottom Flag Interrupt Enable 0 1 read-write 0 The DAC buffer read pointer bottom flag interrupt is disabled. #0 1 The DAC buffer read pointer bottom flag interrupt is enabled. #1 DACBTIEN DAC Buffer Read Pointer Top Flag Interrupt Enable 1 1 read-write 0 The DAC buffer read pointer top flag interrupt is disabled. #0 1 The DAC buffer read pointer top flag interrupt is enabled. #1 DACBWIEN DAC Buffer Watermark Interrupt Enable 2 1 read-write 0 The DAC buffer watermark interrupt is disabled. #0 1 The DAC buffer watermark interrupt is enabled. #1 DACEN DAC Enable 7 1 read-write 0 The DAC system is disabled. #0 1 The DAC system is enabled. #1 DACRFS DAC Reference Select 6 1 read-write 0 The DAC selects DACREF_1 as the reference voltage. #0 1 The DAC selects DACREF_2 as the reference voltage. #1 DACSWTRG DAC Software Trigger 4 1 write-only 0 The DAC soft trigger is not valid. #0 1 The DAC soft trigger is valid. #1 DACTRGSEL DAC Trigger Select 5 1 read-write 0 The DAC hardware trigger is selected. #0 1 The DAC software trigger is selected. #1 LPEN DAC Low Power Control 3 1 read-write 0 High-Power mode #0 1 Low-Power mode #1 C1 DAC Control Register 1 0x22 8 read-write n 0x0 0x0 DACBFEN DAC Buffer Enable 0 1 read-write 0 Buffer read pointer is disabled. The converted data is always the first word of the buffer. #0 1 Buffer read pointer is enabled. The converted data is the word that the read pointer points to. It means converted data can be from any word of the buffer. #1 DACBFMD DAC Buffer Work Mode Select 1 2 read-write 00 Normal mode #00 01 Swing mode #01 10 One-Time Scan mode #10 11 FIFO mode #11 DACBFWM DAC Buffer Watermark Select 3 2 read-write 00 In normal mode, 1 word . In FIFO mode, 2 or less than 2 data remaining in FIFO will set watermark status bit. #00 01 In normal mode, 2 words . In FIFO mode, Max/4 or less than Max/4 data remaining in FIFO will set watermark status bit. #01 10 In normal mode, 3 words . In FIFO mode, Max/2 or less than Max/2 data remaining in FIFO will set watermark status bit. #10 11 In normal mode, 4 words . In FIFO mode, Max-2 or less than Max-2 data remaining in FIFO will set watermark status bit. #11 DMAEN DMA Enable Select 7 1 read-write 0 DMA is disabled. #0 1 DMA is enabled. When DMA is enabled, the DMA request will be generated by original interrupts. The interrupts will not be presented on this module at the same time. #1 C2 DAC Control Register 2 0x23 8 read-write n 0x0 0x0 DACBFRP DAC Buffer Read Pointer 4 4 read-write DACBFUP DAC Buffer Upper Limit 0 4 read-write DAT0H DAC Data High Register 0x2 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT0L DAC Data Low Register 0x0 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT10H DAC Data High Register 0x7A 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT10L DAC Data Low Register 0x6E 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT11H DAC Data High Register 0x91 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT11L DAC Data Low Register 0x84 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT12H DAC Data High Register 0xAA 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT12L DAC Data Low Register 0x9C 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT13H DAC Data High Register 0xC5 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT13L DAC Data Low Register 0xB6 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT14H DAC Data High Register 0xE2 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT14L DAC Data Low Register 0xD2 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT15H DAC Data High Register 0x101 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT15L DAC Data Low Register 0xF0 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT1H DAC Data High Register 0x5 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT1L DAC Data Low Register 0x2 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT2H DAC Data High Register 0xA 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT2L DAC Data Low Register 0x6 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT3H DAC Data High Register 0x11 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT3L DAC Data Low Register 0xC 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT4H DAC Data High Register 0x1A 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT4L DAC Data Low Register 0x14 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT5H DAC Data High Register 0x25 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT5L DAC Data Low Register 0x1E 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT6H DAC Data High Register 0x32 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT6L DAC Data Low Register 0x2A 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT7H DAC Data High Register 0x41 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT7L DAC Data Low Register 0x38 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT8H DAC Data High Register 0x52 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT8L DAC Data Low Register 0x48 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write DAT9H DAC Data High Register 0x65 8 read-write n 0x0 0x0 DATA1 When the DAC Buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula 0 4 read-write DAT9L DAC Data Low Register 0x5A 8 read-write n 0x0 0x0 DATA0 When the DAC buffer is not enabled, DATA[11:0] controls the output voltage based on the following formula: V out = V in * (1 + DACDAT0[11:0])/4096 When the DAC buffer is enabled, DATA is mapped to the 16-word buffer 0 8 read-write SR DAC Status Register 0x20 8 read-write n 0x0 0x0 DACBFRPBF DAC Buffer Read Pointer Bottom Position Flag 0 1 read-write 0 The DAC buffer read pointer is not equal to C2[DACBFUP]. #0 1 The DAC buffer read pointer is equal to C2[DACBFUP]. #1 DACBFRPTF DAC Buffer Read Pointer Top Position Flag 1 1 read-write 0 The DAC buffer read pointer is not zero. #0 1 The DAC buffer read pointer is zero. #1 DACBFWMF DAC Buffer Watermark Flag 2 1 read-write 0 The DAC buffer read pointer has not reached the watermark level. #0 1 The DAC buffer read pointer has reached the watermark level. #1 DMA Enhanced direct memory access controller DMA 0x0 0x0 0x1200 registers n DMA0 0 DMA1 1 DMA2 2 DMA3 3 DMA4 4 DMA5 5 DMA6 6 DMA7 7 DMA8 8 DMA9 9 DMA10 10 DMA11 11 DMA12 12 DMA13 13 DMA14 14 DMA15 15 DMA_Error 16 CDNE Clear DONE Status Bit Register 0x1C 8 write-only n 0x0 0x0 CADN Clears All DONE Bits 6 1 write-only 0 Clears only the TCDn_CSR[DONE] bit specified in the CDNE field #0 1 Clears all bits in TCDn_CSR[DONE] #1 CDNE Clear DONE Bit 0 4 write-only NOP No Op enable 7 1 write-only 0 Normal operation #0 1 No operation, ignore the other bits in this register #1 CEEI Clear Enable Error Interrupt Register 0x18 8 write-only n 0x0 0x0 CAEE Clear All Enable Error Interrupts 6 1 write-only 0 Clear only the EEI bit specified in the CEEI field #0 1 Clear all bits in EEI #1 CEEI Clear Enable Error Interrupt 0 4 write-only NOP No Op enable 7 1 write-only 0 Normal operation #0 1 No operation, ignore the other bits in this register #1 CERQ Clear Enable Request Register 0x1A 8 write-only n 0x0 0x0 CAER Clear All Enable Requests 6 1 write-only 0 Clear only the ERQ bit specified in the CERQ field #0 1 Clear all bits in ERQ #1 CERQ Clear Enable Request 0 4 write-only NOP No Op enable 7 1 write-only 0 Normal operation #0 1 No operation, ignore the other bits in this register #1 CERR Clear Error Register 0x1E 8 write-only n 0x0 0x0 CAEI Clear All Error Indicators 6 1 write-only 0 Clear only the ERR bit specified in the CERR field #0 1 Clear all bits in ERR #1 CERR Clear Error Indicator 0 4 write-only NOP No Op enable 7 1 write-only 0 Normal operation #0 1 No operation, ignore the other bits in this register #1 CINT Clear Interrupt Request Register 0x1F 8 write-only n 0x0 0x0 CAIR Clear All Interrupt Requests 6 1 write-only 0 Clear only the INT bit specified in the CINT field #0 1 Clear all bits in INT #1 CINT Clear Interrupt Request 0 4 write-only NOP No Op enable 7 1 write-only 0 Normal operation #0 1 No operation, ignore the other bits in this register #1 CR Control Register 0x0 32 read-write n 0x0 0x0 CLM Continuous Link Mode 6 1 read-write 0 A minor loop channel link made to itself goes through channel arbitration before being activated again. #0 1 A minor loop channel link made to itself does not go through channel arbitration before being activated again. Upon minor loop completion, the channel activates again if that channel has a minor loop channel link enabled and the link channel is itself. This effectively applies the minor loop offsets and restarts the next minor loop. #1 CX Cancel Transfer 17 1 read-write 0 Normal operation #0 1 Cancel the remaining data transfer. Stop the executing channel and force the minor loop to finish. The cancel takes effect after the last write of the current read/write sequence. The CX bit clears itself after the cancel has been honored. This cancel retires the channel normally as if the minor loop was completed. #1 ECX Error Cancel Transfer 16 1 read-write 0 Normal operation #0 1 Cancel the remaining data transfer in the same fashion as the CX bit. Stop the executing channel and force the minor loop to finish. The cancel takes effect after the last write of the current read/write sequence. The ECX bit clears itself after the cancel is honored. In addition to cancelling the transfer, ECX treats the cancel as an error condition, thus updating the Error Status register (DMAx_ES) and generating an optional error interrupt. #1 EDBG Enable Debug 1 1 read-write 0 When in debug mode, the DMA continues to operate. #0 1 When in debug mode, the DMA stalls the start of a new channel. Executing channels are allowed to complete. Channel execution resumes when the system exits debug mode or the EDBG bit is cleared. #1 EMLM Enable Minor Loop Mapping 7 1 read-write 0 Disabled. TCDn.word2 is defined as a 32-bit NBYTES field. #0 1 Enabled. TCDn.word2 is redefined to include individual enable fields, an offset field, and the NBYTES field. The individual enable fields allow the minor loop offset to be applied to the source address, the destination address, or both. The NBYTES field is reduced when either offset is enabled. #1 ERCA Enable Round Robin Channel Arbitration 2 1 read-write 0 Fixed priority arbitration is used for channel selection . #0 1 Round robin arbitration is used for channel selection . #1 HALT Halt DMA Operations 5 1 read-write 0 Normal operation #0 1 Stall the start of any new channels. Executing channels are allowed to complete. Channel execution resumes when this bit is cleared. #1 HOE Halt On Error 4 1 read-write 0 Normal operation #0 1 Any error causes the HALT bit to set. Subsequently, all service requests are ignored until the HALT bit is cleared. #1 DCHPRI0 Channel n Priority Register 0x506 8 read-write n 0x0 0x0 CHPRI Channel n Arbitration Priority 0 4 read-write DPA Disable Preempt Ability 6 1 read-write 0 Channel n can suspend a lower priority channel #0 1 Channel n cannot suspend any channel, regardless of channel priority #1 ECP Enable Channel Preemption 7 1 read-write 0 Channel n cannot be suspended by a higher priority channel's service request #0 1 Channel n can be temporarily suspended by the service request of a higher priority channel #1 DCHPRI1 Channel n Priority Register 0x403 8 read-write n 0x0 0x0 CHPRI Channel n Arbitration Priority 0 4 read-write DPA Disable Preempt Ability 6 1 read-write 0 Channel n can suspend a lower priority channel #0 1 Channel n cannot suspend any channel, regardless of channel priority #1 ECP Enable Channel Preemption 7 1 read-write 0 Channel n cannot be suspended by a higher priority channel's service request #0 1 Channel n can be temporarily suspended by the service request of a higher priority channel #1 DCHPRI10 Channel n Priority Register 0xB2D 8 read-write n 0x0 0x0 CHPRI Channel n Arbitration Priority 0 4 read-write DPA Disable Preempt Ability 6 1 read-write 0 Channel n can suspend a lower priority channel #0 1 Channel n cannot suspend any channel, regardless of channel priority #1 ECP Enable Channel Preemption 7 1 read-write 0 Channel n cannot be suspended by a higher priority channel's service request #0 1 Channel n can be temporarily suspended by the service request of a higher priority channel #1 DCHPRI11 Channel n Priority Register 0xA24 8 read-write n 0x0 0x0 CHPRI Channel n Arbitration Priority 0 4 read-write DPA Disable Preempt Ability 6 1 read-write 0 Channel n can suspend a lower priority channel #0 1 Channel n cannot suspend any channel, regardless of channel priority #1 ECP Enable Channel Preemption 7 1 read-write 0 Channel n cannot be suspended by a higher priority channel's service request #0 1 Channel n can be temporarily suspended by the service request of a higher priority channel #1 DCHPRI12 Channel n Priority Register 0x1178 8 read-write n 0x0 0x0 CHPRI Channel n Arbitration Priority 0 4 read-write DPA Disable Preempt Ability 6 1 read-write 0 Channel n can suspend a lower priority channel #0 1 Channel n cannot suspend any channel, regardless of channel priority #1 ECP Enable Channel Preemption 7 1 read-write 0 Channel n cannot be suspended by a higher priority channel's service request #0 1 Channel n can be temporarily suspended by the service request of a higher priority channel #1 DCHPRI13 Channel n Priority Register 0x1069 8 read-write n 0x0 0x0 CHPRI Channel n Arbitration Priority 0 4 read-write DPA Disable Preempt Ability 6 1 read-write 0 Channel n can suspend a lower priority channel #0 1 Channel n cannot suspend any channel, regardless of channel priority #1 ECP Enable Channel Preemption 7 1 read-write 0 Channel n cannot be suspended by a higher priority channel's service request #0 1 Channel n can be temporarily suspended by the service request of a higher priority channel #1 DCHPRI14 Channel n Priority Register 0xF5B 8 read-write n 0x0 0x0 CHPRI Channel n Arbitration Priority 0 4 read-write DPA Disable Preempt Ability 6 1 read-write 0 Channel n can suspend a lower priority channel #0 1 Channel n cannot suspend any channel, regardless of channel priority #1 ECP Enable Channel Preemption 7 1 read-write 0 Channel n cannot be suspended by a higher priority channel's service request #0 1 Channel n can be temporarily suspended by the service request of a higher priority channel #1 DCHPRI15 Channel n Priority Register 0xE4E 8 read-write n 0x0 0x0 CHPRI Channel n Arbitration Priority 0 4 read-write DPA Disable Preempt Ability 6 1 read-write 0 Channel n can suspend a lower priority channel #0 1 Channel n cannot suspend any channel, regardless of channel priority #1 ECP Enable Channel Preemption 7 1 read-write 0 Channel n cannot be suspended by a higher priority channel's service request #0 1 Channel n can be temporarily suspended by the service request of a higher priority channel #1 DCHPRI2 Channel n Priority Register 0x301 8 read-write n 0x0 0x0 CHPRI Channel n Arbitration Priority 0 4 read-write DPA Disable Preempt Ability 6 1 read-write 0 Channel n can suspend a lower priority channel #0 1 Channel n cannot suspend any channel, regardless of channel priority #1 ECP Enable Channel Preemption 7 1 read-write 0 Channel n cannot be suspended by a higher priority channel's service request #0 1 Channel n can be temporarily suspended by the service request of a higher priority channel #1 DCHPRI3 Channel n Priority Register 0x200 8 read-write n 0x0 0x0 CHPRI Channel n Arbitration Priority 0 4 read-write DPA Disable Preempt Ability 6 1 read-write 0 Channel n can suspend a lower priority channel #0 1 Channel n cannot suspend any channel, regardless of channel priority #1 ECP Enable Channel Preemption 7 1 read-write 0 Channel n cannot be suspended by a higher priority channel's service request #0 1 Channel n can be temporarily suspended by the service request of a higher priority channel #1 DCHPRI4 Channel n Priority Register 0x91C 8 read-write n 0x0 0x0 CHPRI Channel n Arbitration Priority 0 4 read-write DPA Disable Preempt Ability 6 1 read-write 0 Channel n can suspend a lower priority channel #0 1 Channel n cannot suspend any channel, regardless of channel priority #1 ECP Enable Channel Preemption 7 1 read-write 0 Channel n cannot be suspended by a higher priority channel's service request #0 1 Channel n can be temporarily suspended by the service request of a higher priority channel #1 DCHPRI5 Channel n Priority Register 0x815 8 read-write n 0x0 0x0 CHPRI Channel n Arbitration Priority 0 4 read-write DPA Disable Preempt Ability 6 1 read-write 0 Channel n can suspend a lower priority channel #0 1 Channel n cannot suspend any channel, regardless of channel priority #1 ECP Enable Channel Preemption 7 1 read-write 0 Channel n cannot be suspended by a higher priority channel's service request #0 1 Channel n can be temporarily suspended by the service request of a higher priority channel #1 DCHPRI6 Channel n Priority Register 0x70F 8 read-write n 0x0 0x0 CHPRI Channel n Arbitration Priority 0 4 read-write DPA Disable Preempt Ability 6 1 read-write 0 Channel n can suspend a lower priority channel #0 1 Channel n cannot suspend any channel, regardless of channel priority #1 ECP Enable Channel Preemption 7 1 read-write 0 Channel n cannot be suspended by a higher priority channel's service request #0 1 Channel n can be temporarily suspended by the service request of a higher priority channel #1 DCHPRI7 Channel n Priority Register 0x60A 8 read-write n 0x0 0x0 CHPRI Channel n Arbitration Priority 0 4 read-write DPA Disable Preempt Ability 6 1 read-write 0 Channel n can suspend a lower priority channel #0 1 Channel n cannot suspend any channel, regardless of channel priority #1 ECP Enable Channel Preemption 7 1 read-write 0 Channel n cannot be suspended by a higher priority channel's service request #0 1 Channel n can be temporarily suspended by the service request of a higher priority channel #1 DCHPRI8 Channel n Priority Register 0xD42 8 read-write n 0x0 0x0 CHPRI Channel n Arbitration Priority 0 4 read-write DPA Disable Preempt Ability 6 1 read-write 0 Channel n can suspend a lower priority channel #0 1 Channel n cannot suspend any channel, regardless of channel priority #1 ECP Enable Channel Preemption 7 1 read-write 0 Channel n cannot be suspended by a higher priority channel's service request #0 1 Channel n can be temporarily suspended by the service request of a higher priority channel #1 DCHPRI9 Channel n Priority Register 0xC37 8 read-write n 0x0 0x0 CHPRI Channel n Arbitration Priority 0 4 read-write DPA Disable Preempt Ability 6 1 read-write 0 Channel n can suspend a lower priority channel #0 1 Channel n cannot suspend any channel, regardless of channel priority #1 ECP Enable Channel Preemption 7 1 read-write 0 Channel n cannot be suspended by a higher priority channel's service request #0 1 Channel n can be temporarily suspended by the service request of a higher priority channel #1 EARS Enable Asynchronous Request in Stop Register 0x44 32 read-write n 0x0 0x0 EDREQ_0 Enable asynchronous DMA request in stop for channel 0. 0 1 read-write 0 Disable asynchronous DMA request for channel 0. #0 1 Enable asynchronous DMA request for channel 0. #1 EDREQ_1 Enable asynchronous DMA request in stop for channel 1. 1 1 read-write 0 Disable asynchronous DMA request for channel 1 #0 1 Enable asynchronous DMA request for channel 1. #1 EDREQ_10 Enable asynchronous DMA request in stop for channel 10 10 1 read-write 0 Disable asynchronous DMA request for channel 10. #0 1 Enable asynchronous DMA request for channel 10. #1 EDREQ_11 Enable asynchronous DMA request in stop for channel 11 11 1 read-write 0 Disable asynchronous DMA request for channel 11. #0 1 Enable asynchronous DMA request for channel 11. #1 EDREQ_12 Enable asynchronous DMA request in stop for channel 12 12 1 read-write 0 Disable asynchronous DMA request for channel 12. #0 1 Enable asynchronous DMA request for channel 12. #1 EDREQ_13 Enable asynchronous DMA request in stop for channel 13 13 1 read-write 0 Disable asynchronous DMA request for channel 13. #0 1 Enable asynchronous DMA request for channel 13. #1 EDREQ_14 Enable asynchronous DMA request in stop for channel 14 14 1 read-write 0 Disable asynchronous DMA request for channel 14. #0 1 Enable asynchronous DMA request for channel 14. #1 EDREQ_15 Enable asynchronous DMA request in stop for channel 15 15 1 read-write 0 Disable asynchronous DMA request for channel 15. #0 1 Enable asynchronous DMA request for channel 15. #1 EDREQ_2 Enable asynchronous DMA request in stop for channel 2. 2 1 read-write 0 Disable asynchronous DMA request for channel 2. #0 1 Enable asynchronous DMA request for channel 2. #1 EDREQ_3 Enable asynchronous DMA request in stop for channel 3. 3 1 read-write 0 Disable asynchronous DMA request for channel 3. #0 1 Enable asynchronous DMA request for channel 3. #1 EDREQ_4 Enable asynchronous DMA request in stop for channel 4 4 1 read-write 0 Disable asynchronous DMA request for channel 4. #0 1 Enable asynchronous DMA request for channel 4. #1 EDREQ_5 Enable asynchronous DMA request in stop for channel 5 5 1 read-write 0 Disable asynchronous DMA request for channel 5. #0 1 Enable asynchronous DMA request for channel 5. #1 EDREQ_6 Enable asynchronous DMA request in stop for channel 6 6 1 read-write 0 Disable asynchronous DMA request for channel 6. #0 1 Enable asynchronous DMA request for channel 6. #1 EDREQ_7 Enable asynchronous DMA request in stop for channel 7 7 1 read-write 0 Disable asynchronous DMA request for channel 7. #0 1 Enable asynchronous DMA request for channel 7. #1 EDREQ_8 Enable asynchronous DMA request in stop for channel 8 8 1 read-write 0 Disable asynchronous DMA request for channel 8. #0 1 Enable asynchronous DMA request for channel 8. #1 EDREQ_9 Enable asynchronous DMA request in stop for channel 9 9 1 read-write 0 Disable asynchronous DMA request for channel 9. #0 1 Enable asynchronous DMA request for channel 9. #1 EEI Enable Error Interrupt Register 0x14 32 read-write n 0x0 0x0 EEI0 Enable Error Interrupt 0 0 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI1 Enable Error Interrupt 1 1 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI10 Enable Error Interrupt 10 10 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI11 Enable Error Interrupt 11 11 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI12 Enable Error Interrupt 12 12 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI13 Enable Error Interrupt 13 13 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI14 Enable Error Interrupt 14 14 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI15 Enable Error Interrupt 15 15 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI2 Enable Error Interrupt 2 2 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI3 Enable Error Interrupt 3 3 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI4 Enable Error Interrupt 4 4 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI5 Enable Error Interrupt 5 5 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI6 Enable Error Interrupt 6 6 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI7 Enable Error Interrupt 7 7 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI8 Enable Error Interrupt 8 8 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 EEI9 Enable Error Interrupt 9 9 1 read-write 0 The error signal for corresponding channel does not generate an error interrupt #0 1 The assertion of the error signal for corresponding channel generates an error interrupt request #1 ERQ Enable Request Register 0xC 32 read-write n 0x0 0x0 ERQ0 Enable DMA Request 0 0 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ1 Enable DMA Request 1 1 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ10 Enable DMA Request 10 10 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ11 Enable DMA Request 11 11 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ12 Enable DMA Request 12 12 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ13 Enable DMA Request 13 13 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ14 Enable DMA Request 14 14 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ15 Enable DMA Request 15 15 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ2 Enable DMA Request 2 2 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ3 Enable DMA Request 3 3 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ4 Enable DMA Request 4 4 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ5 Enable DMA Request 5 5 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ6 Enable DMA Request 6 6 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ7 Enable DMA Request 7 7 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ8 Enable DMA Request 8 8 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERQ9 Enable DMA Request 9 9 1 read-write 0 The DMA request signal for the corresponding channel is disabled #0 1 The DMA request signal for the corresponding channel is enabled #1 ERR Error Register 0x2C 32 read-write n 0x0 0x0 ERR0 Error In Channel 0 0 1 read-write 0 An error in the corresponding channel has not occurred #0 1 An error in the corresponding channel has occurred #1 ERR1 Error In Channel 1 1 1 read-write 0 An error in the corresponding channel has not occurred #0 1 An error in the corresponding channel has occurred #1 ERR10 Error In Channel 10 10 1 read-write 0 An error in the corresponding channel has not occurred #0 1 An error in the corresponding channel has occurred #1 ERR11 Error In Channel 11 11 1 read-write 0 An error in the corresponding channel has not occurred #0 1 An error in the corresponding channel has occurred #1 ERR12 Error In Channel 12 12 1 read-write 0 An error in the corresponding channel has not occurred #0 1 An error in the corresponding channel has occurred #1 ERR13 Error In Channel 13 13 1 read-write 0 An error in the corresponding channel has not occurred #0 1 An error in the corresponding channel has occurred #1 ERR14 Error In Channel 14 14 1 read-write 0 An error in the corresponding channel has not occurred #0 1 An error in the corresponding channel has occurred #1 ERR15 Error In Channel 15 15 1 read-write 0 An error in the corresponding channel has not occurred #0 1 An error in the corresponding channel has occurred #1 ERR2 Error In Channel 2 2 1 read-write 0 An error in the corresponding channel has not occurred #0 1 An error in the corresponding channel has occurred #1 ERR3 Error In Channel 3 3 1 read-write 0 An error in the corresponding channel has not occurred #0 1 An error in the corresponding channel has occurred #1 ERR4 Error In Channel 4 4 1 read-write 0 An error in the corresponding channel has not occurred #0 1 An error in the corresponding channel has occurred #1 ERR5 Error In Channel 5 5 1 read-write 0 An error in the corresponding channel has not occurred #0 1 An error in the corresponding channel has occurred #1 ERR6 Error In Channel 6 6 1 read-write 0 An error in the corresponding channel has not occurred #0 1 An error in the corresponding channel has occurred #1 ERR7 Error In Channel 7 7 1 read-write 0 An error in the corresponding channel has not occurred #0 1 An error in the corresponding channel has occurred #1 ERR8 Error In Channel 8 8 1 read-write 0 An error in the corresponding channel has not occurred #0 1 An error in the corresponding channel has occurred #1 ERR9 Error In Channel 9 9 1 read-write 0 An error in the corresponding channel has not occurred #0 1 An error in the corresponding channel has occurred #1 ES Error Status Register 0x4 32 read-only n 0x0 0x0 CPE Channel Priority Error 14 1 read-only 0 No channel priority error #0 1 The last recorded error was a configuration error in the channel priorities . Channel priorities are not unique. #1 DAE Destination Address Error 5 1 read-only 0 No destination address configuration error #0 1 The last recorded error was a configuration error detected in the TCDn_DADDR field. TCDn_DADDR is inconsistent with TCDn_ATTR[DSIZE]. #1 DBE Destination Bus Error 0 1 read-only 0 No destination bus error #0 1 The last recorded error was a bus error on a destination write #1 DOE Destination Offset Error 4 1 read-only 0 No destination offset configuration error #0 1 The last recorded error was a configuration error detected in the TCDn_DOFF field. TCDn_DOFF is inconsistent with TCDn_ATTR[DSIZE]. #1 ECX Transfer Canceled 16 1 read-only 0 No canceled transfers #0 1 The last recorded entry was a canceled transfer by the error cancel transfer input #1 ERRCHN Error Channel Number or Canceled Channel Number 8 4 read-only NCE NBYTES/CITER Configuration Error 3 1 read-only 0 No NBYTES/CITER configuration error #0 1 The last recorded error was a configuration error detected in the TCDn_NBYTES or TCDn_CITER fields. TCDn_NBYTES is not a multiple of TCDn_ATTR[SSIZE] and TCDn_ATTR[DSIZE], or TCDn_CITER[CITER] is equal to zero, or TCDn_CITER[ELINK] is not equal to TCDn_BITER[ELINK] #1 SAE Source Address Error 7 1 read-only 0 No source address configuration error. #0 1 The last recorded error was a configuration error detected in the TCDn_SADDR field. TCDn_SADDR is inconsistent with TCDn_ATTR[SSIZE]. #1 SBE Source Bus Error 1 1 read-only 0 No source bus error #0 1 The last recorded error was a bus error on a source read #1 SGE Scatter/Gather Configuration Error 2 1 read-only 0 No scatter/gather configuration error #0 1 The last recorded error was a configuration error detected in the TCDn_DLASTSGA field. This field is checked at the beginning of a scatter/gather operation after major loop completion if TCDn_CSR[ESG] is enabled. TCDn_DLASTSGA is not on a 32 byte boundary. #1 SOE Source Offset Error 6 1 read-only 0 No source offset configuration error #0 1 The last recorded error was a configuration error detected in the TCDn_SOFF field. TCDn_SOFF is inconsistent with TCDn_ATTR[SSIZE]. #1 VLD Logical OR of all ERR status bits 31 1 read-only 0 No ERR bits are set #0 1 At least one ERR bit is set indicating a valid error exists that has not been cleared #1 HRS Hardware Request Status Register 0x34 32 read-only n 0x0 0x0 HRS0 Hardware Request Status Channel 0 0 1 read-only 0 A hardware service request for channel 0 is not present #0 1 A hardware service request for channel 0 is present #1 HRS1 Hardware Request Status Channel 1 1 1 read-only 0 A hardware service request for channel 1 is not present #0 1 A hardware service request for channel 1 is present #1 HRS10 Hardware Request Status Channel 10 10 1 read-only 0 A hardware service request for channel 10 is not present #0 1 A hardware service request for channel 10 is present #1 HRS11 Hardware Request Status Channel 11 11 1 read-only 0 A hardware service request for channel 11 is not present #0 1 A hardware service request for channel 11 is present #1 HRS12 Hardware Request Status Channel 12 12 1 read-only 0 A hardware service request for channel 12 is not present #0 1 A hardware service request for channel 12 is present #1 HRS13 Hardware Request Status Channel 13 13 1 read-only 0 A hardware service request for channel 13 is not present #0 1 A hardware service request for channel 13 is present #1 HRS14 Hardware Request Status Channel 14 14 1 read-only 0 A hardware service request for channel 14 is not present #0 1 A hardware service request for channel 14 is present #1 HRS15 Hardware Request Status Channel 15 15 1 read-only 0 A hardware service request for channel 15 is not present #0 1 A hardware service request for channel 15 is present #1 HRS2 Hardware Request Status Channel 2 2 1 read-only 0 A hardware service request for channel 2 is not present #0 1 A hardware service request for channel 2 is present #1 HRS3 Hardware Request Status Channel 3 3 1 read-only 0 A hardware service request for channel 3 is not present #0 1 A hardware service request for channel 3 is present #1 HRS4 Hardware Request Status Channel 4 4 1 read-only 0 A hardware service request for channel 4 is not present #0 1 A hardware service request for channel 4 is present #1 HRS5 Hardware Request Status Channel 5 5 1 read-only 0 A hardware service request for channel 5 is not present #0 1 A hardware service request for channel 5 is present #1 HRS6 Hardware Request Status Channel 6 6 1 read-only 0 A hardware service request for channel 6 is not present #0 1 A hardware service request for channel 6 is present #1 HRS7 Hardware Request Status Channel 7 7 1 read-only 0 A hardware service request for channel 7 is not present #0 1 A hardware service request for channel 7 is present #1 HRS8 Hardware Request Status Channel 8 8 1 read-only 0 A hardware service request for channel 8 is not present #0 1 A hardware service request for channel 8 is present #1 HRS9 Hardware Request Status Channel 9 9 1 read-only 0 A hardware service request for channel 9 is not present #0 1 A hardware service request for channel 9 is present #1 INT Interrupt Request Register 0x24 32 read-write n 0x0 0x0 INT0 Interrupt Request 0 0 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT1 Interrupt Request 1 1 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT10 Interrupt Request 10 10 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT11 Interrupt Request 11 11 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT12 Interrupt Request 12 12 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT13 Interrupt Request 13 13 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT14 Interrupt Request 14 14 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT15 Interrupt Request 15 15 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT2 Interrupt Request 2 2 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT3 Interrupt Request 3 3 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT4 Interrupt Request 4 4 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT5 Interrupt Request 5 5 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT6 Interrupt Request 6 6 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT7 Interrupt Request 7 7 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT8 Interrupt Request 8 8 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 INT9 Interrupt Request 9 9 1 read-write 0 The interrupt request for corresponding channel is cleared #0 1 The interrupt request for corresponding channel is active #1 SEEI Set Enable Error Interrupt Register 0x19 8 write-only n 0x0 0x0 NOP No Op enable 7 1 write-only 0 Normal operation #0 1 No operation, ignore the other bits in this register #1 SAEE Sets All Enable Error Interrupts 6 1 write-only 0 Set only the EEI bit specified in the SEEI field. #0 1 Sets all bits in EEI #1 SEEI Set Enable Error Interrupt 0 4 write-only SERQ Set Enable Request Register 0x1B 8 write-only n 0x0 0x0 NOP No Op enable 7 1 write-only 0 Normal operation #0 1 No operation, ignore the other bits in this register #1 SAER Set All Enable Requests 6 1 write-only 0 Set only the ERQ bit specified in the SERQ field #0 1 Set all bits in ERQ #1 SERQ Set enable request 0 4 write-only SSRT Set START Bit Register 0x1D 8 write-only n 0x0 0x0 NOP No Op enable 7 1 write-only 0 Normal operation #0 1 No operation, ignore the other bits in this register #1 SAST Set All START Bits (activates all channels) 6 1 write-only 0 Set only the TCDn_CSR[START] bit specified in the SSRT field #0 1 Set all bits in TCDn_CSR[START] #1 SSRT Set START Bit 0 4 write-only TCD0_ATTR TCD Transfer Attributes 0x200C 16 read-write n 0x0 0x0 DMOD Destination Address Modulo 3 5 read-write DSIZE Destination Data Transfer Size 0 3 read-write SMOD Source Address Modulo. 11 5 read-write 0 Source address modulo feature is disabled #00000 SSIZE Source data transfer size 8 3 read-write 000 8-bit #000 001 16-bit #001 010 32-bit #010 100 16-byte #100 101 32-byte #101 TCD0_BITER_ELINKNO TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x203C 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 15 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD0_BITER_ELINKYES TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x203C 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 9 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD0_CITER_ELINKNO TCD Current Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x202C 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 15 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD0_CITER_ELINKYES TCD Current Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x202C 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 9 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD0_CSR TCD Control and Status 0x2038 16 read-write n 0x0 0x0 ACTIVE Channel Active 6 1 read-write BWC Bandwidth Control 14 2 read-write 00 No eDMA engine stalls #00 10 eDMA engine stalls for 4 cycles after each r/w #10 11 eDMA engine stalls for 8 cycles after each r/w #11 DONE Channel Done 7 1 read-write DREQ Disable Request 3 1 read-write 0 The channel's ERQ bit is not affected #0 1 The channel's ERQ bit is cleared when the major loop is complete #1 ESG Enable Scatter/Gather Processing 4 1 read-write 0 The current channel's TCD is normal format. #0 1 The current channel's TCD specifies a scatter gather format. The DLASTSGA field provides a memory pointer to the next TCD to be loaded into this channel after the major loop completes its execution. #1 INTHALF Enable an interrupt when major counter is half complete. 2 1 read-write 0 The half-point interrupt is disabled #0 1 The half-point interrupt is enabled #1 INTMAJOR Enable an interrupt when major iteration count completes 1 1 read-write 0 The end-of-major loop interrupt is disabled #0 1 The end-of-major loop interrupt is enabled #1 MAJORELINK Enable channel-to-channel linking on major loop complete 5 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 MAJORLINKCH Link Channel Number 8 4 read-write START Channel Start 0 1 read-write 0 The channel is not explicitly started #0 1 The channel is explicitly started via a software initiated service request #1 TCD0_DADDR TCD Destination Address 0x2020 32 read-write n 0x0 0x0 DADDR Destination Address 0 32 read-write TCD0_DLASTSGA TCD Last Destination Address Adjustment/Scatter Gather Address 0x2030 32 read-write n 0x0 0x0 DLASTSGA Destination last address adjustment or the memory address for the next transfer control descriptor to be loaded into this channel (scatter/gather) 0 32 read-write TCD0_DOFF TCD Signed Destination Address Offset 0x2028 16 read-write n 0x0 0x0 DOFF Destination Address Signed offset 0 16 read-write TCD0_NBYTES_MLNO TCD Minor Byte Count (Minor Loop Disabled) DMA 0x2010 32 read-write n 0x0 0x0 NBYTES Minor Byte Transfer Count 0 32 read-write TCD0_NBYTES_MLOFFNO TCD Signed Minor Loop Offset (Minor Loop Enabled and Offset Disabled) DMA 0x2010 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 NBYTES Minor Byte Transfer Count 0 30 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD0_NBYTES_MLOFFYES TCD Signed Minor Loop Offset (Minor Loop and Offset Enabled) DMA 0x2010 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 MLOFF If SMLOE or DMLOE is set, this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes. 10 20 read-write NBYTES Minor Byte Transfer Count 0 10 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD0_SADDR TCD Source Address 0x2000 32 read-write n 0x0 0x0 SADDR Source Address 0 32 read-write TCD0_SLAST TCD Last Source Address Adjustment 0x2018 32 read-write n 0x0 0x0 SLAST Last source Address Adjustment 0 32 read-write TCD0_SOFF TCD Signed Source Address Offset 0x2008 16 read-write n 0x0 0x0 SOFF Source address signed offset 0 16 read-write TCD10_ATTR TCD Transfer Attributes 0xC728 16 read-write n 0x0 0x0 DMOD Destination Address Modulo 3 5 read-write DSIZE Destination Data Transfer Size 0 3 read-write SMOD Source Address Modulo. 11 5 read-write 0 Source address modulo feature is disabled #00000 SSIZE Source data transfer size 8 3 read-write 000 8-bit #000 001 16-bit #001 010 32-bit #010 100 16-byte #100 101 32-byte #101 TCD10_BITER_ELINKNO TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0xC848 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 15 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD10_BITER_ELINKYES TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0xC848 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 9 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD10_CITER_ELINKNO TCD Current Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0xC7E8 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 15 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD10_CITER_ELINKYES TCD Current Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0xC7E8 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 9 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD10_CSR TCD Control and Status 0xC830 16 read-write n 0x0 0x0 ACTIVE Channel Active 6 1 read-write BWC Bandwidth Control 14 2 read-write 00 No eDMA engine stalls #00 10 eDMA engine stalls for 4 cycles after each r/w #10 11 eDMA engine stalls for 8 cycles after each r/w #11 DONE Channel Done 7 1 read-write DREQ Disable Request 3 1 read-write 0 The channel's ERQ bit is not affected #0 1 The channel's ERQ bit is cleared when the major loop is complete #1 ESG Enable Scatter/Gather Processing 4 1 read-write 0 The current channel's TCD is normal format. #0 1 The current channel's TCD specifies a scatter gather format. The DLASTSGA field provides a memory pointer to the next TCD to be loaded into this channel after the major loop completes its execution. #1 INTHALF Enable an interrupt when major counter is half complete. 2 1 read-write 0 The half-point interrupt is disabled #0 1 The half-point interrupt is enabled #1 INTMAJOR Enable an interrupt when major iteration count completes 1 1 read-write 0 The end-of-major loop interrupt is disabled #0 1 The end-of-major loop interrupt is enabled #1 MAJORELINK Enable channel-to-channel linking on major loop complete 5 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 MAJORLINKCH Link Channel Number 8 4 read-write START Channel Start 0 1 read-write 0 The channel is not explicitly started #0 1 The channel is explicitly started via a software initiated service request #1 TCD10_DADDR TCD Destination Address 0xC7A0 32 read-write n 0x0 0x0 DADDR Destination Address 0 32 read-write TCD10_DLASTSGA TCD Last Destination Address Adjustment/Scatter Gather Address 0xC800 32 read-write n 0x0 0x0 DLASTSGA Destination last address adjustment or the memory address for the next transfer control descriptor to be loaded into this channel (scatter/gather) 0 32 read-write TCD10_DOFF TCD Signed Destination Address Offset 0xC7D0 16 read-write n 0x0 0x0 DOFF Destination Address Signed offset 0 16 read-write TCD10_NBYTES_MLNO TCD Minor Byte Count (Minor Loop Disabled) DMA 0xC740 32 read-write n 0x0 0x0 NBYTES Minor Byte Transfer Count 0 32 read-write TCD10_NBYTES_MLOFFNO TCD Signed Minor Loop Offset (Minor Loop Enabled and Offset Disabled) DMA 0xC740 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 NBYTES Minor Byte Transfer Count 0 30 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD10_NBYTES_MLOFFYES TCD Signed Minor Loop Offset (Minor Loop and Offset Enabled) DMA 0xC740 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 MLOFF If SMLOE or DMLOE is set, this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes. 10 20 read-write NBYTES Minor Byte Transfer Count 0 10 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD10_SADDR TCD Source Address 0xC6E0 32 read-write n 0x0 0x0 SADDR Source Address 0 32 read-write TCD10_SLAST TCD Last Source Address Adjustment 0xC770 32 read-write n 0x0 0x0 SLAST Last source Address Adjustment 0 32 read-write TCD10_SOFF TCD Signed Source Address Offset 0xC710 16 read-write n 0x0 0x0 SOFF Source address signed offset 0 16 read-write TCD11_ATTR TCD Transfer Attributes 0xD88E 16 read-write n 0x0 0x0 DMOD Destination Address Modulo 3 5 read-write DSIZE Destination Data Transfer Size 0 3 read-write SMOD Source Address Modulo. 11 5 read-write 0 Source address modulo feature is disabled #00000 SSIZE Source data transfer size 8 3 read-write 000 8-bit #000 001 16-bit #001 010 32-bit #010 100 16-byte #100 101 32-byte #101 TCD11_BITER_ELINKNO TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0xD9C6 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 15 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD11_BITER_ELINKYES TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0xD9C6 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 9 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD11_CITER_ELINKNO TCD Current Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0xD95E 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 15 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD11_CITER_ELINKYES TCD Current Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0xD95E 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 9 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD11_CSR TCD Control and Status 0xD9AC 16 read-write n 0x0 0x0 ACTIVE Channel Active 6 1 read-write BWC Bandwidth Control 14 2 read-write 00 No eDMA engine stalls #00 10 eDMA engine stalls for 4 cycles after each r/w #10 11 eDMA engine stalls for 8 cycles after each r/w #11 DONE Channel Done 7 1 read-write DREQ Disable Request 3 1 read-write 0 The channel's ERQ bit is not affected #0 1 The channel's ERQ bit is cleared when the major loop is complete #1 ESG Enable Scatter/Gather Processing 4 1 read-write 0 The current channel's TCD is normal format. #0 1 The current channel's TCD specifies a scatter gather format. The DLASTSGA field provides a memory pointer to the next TCD to be loaded into this channel after the major loop completes its execution. #1 INTHALF Enable an interrupt when major counter is half complete. 2 1 read-write 0 The half-point interrupt is disabled #0 1 The half-point interrupt is enabled #1 INTMAJOR Enable an interrupt when major iteration count completes 1 1 read-write 0 The end-of-major loop interrupt is disabled #0 1 The end-of-major loop interrupt is enabled #1 MAJORELINK Enable channel-to-channel linking on major loop complete 5 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 MAJORLINKCH Link Channel Number 8 4 read-write START Channel Start 0 1 read-write 0 The channel is not explicitly started #0 1 The channel is explicitly started via a software initiated service request #1 TCD11_DADDR TCD Destination Address 0xD910 32 read-write n 0x0 0x0 DADDR Destination Address 0 32 read-write TCD11_DLASTSGA TCD Last Destination Address Adjustment/Scatter Gather Address 0xD978 32 read-write n 0x0 0x0 DLASTSGA Destination last address adjustment or the memory address for the next transfer control descriptor to be loaded into this channel (scatter/gather) 0 32 read-write TCD11_DOFF TCD Signed Destination Address Offset 0xD944 16 read-write n 0x0 0x0 DOFF Destination Address Signed offset 0 16 read-write TCD11_NBYTES_MLNO TCD Minor Byte Count (Minor Loop Disabled) DMA 0xD8A8 32 read-write n 0x0 0x0 NBYTES Minor Byte Transfer Count 0 32 read-write TCD11_NBYTES_MLOFFNO TCD Signed Minor Loop Offset (Minor Loop Enabled and Offset Disabled) DMA 0xD8A8 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 NBYTES Minor Byte Transfer Count 0 30 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD11_NBYTES_MLOFFYES TCD Signed Minor Loop Offset (Minor Loop and Offset Enabled) DMA 0xD8A8 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 MLOFF If SMLOE or DMLOE is set, this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes. 10 20 read-write NBYTES Minor Byte Transfer Count 0 10 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD11_SADDR TCD Source Address 0xD840 32 read-write n 0x0 0x0 SADDR Source Address 0 32 read-write TCD11_SLAST TCD Last Source Address Adjustment 0xD8DC 32 read-write n 0x0 0x0 SLAST Last source Address Adjustment 0 32 read-write TCD11_SOFF TCD Signed Source Address Offset 0xD874 16 read-write n 0x0 0x0 SOFF Source address signed offset 0 16 read-write TCD12_ATTR TCD Transfer Attributes 0xEA14 16 read-write n 0x0 0x0 DMOD Destination Address Modulo 3 5 read-write DSIZE Destination Data Transfer Size 0 3 read-write SMOD Source Address Modulo. 11 5 read-write 0 Source address modulo feature is disabled #00000 SSIZE Source data transfer size 8 3 read-write 000 8-bit #000 001 16-bit #001 010 32-bit #010 100 16-byte #100 101 32-byte #101 TCD12_BITER_ELINKNO TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0xEB64 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 15 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD12_BITER_ELINKYES TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0xEB64 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 9 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD12_CITER_ELINKNO TCD Current Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0xEAF4 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 15 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD12_CITER_ELINKYES TCD Current Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0xEAF4 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 9 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD12_CSR TCD Control and Status 0xEB48 16 read-write n 0x0 0x0 ACTIVE Channel Active 6 1 read-write BWC Bandwidth Control 14 2 read-write 00 No eDMA engine stalls #00 10 eDMA engine stalls for 4 cycles after each r/w #10 11 eDMA engine stalls for 8 cycles after each r/w #11 DONE Channel Done 7 1 read-write DREQ Disable Request 3 1 read-write 0 The channel's ERQ bit is not affected #0 1 The channel's ERQ bit is cleared when the major loop is complete #1 ESG Enable Scatter/Gather Processing 4 1 read-write 0 The current channel's TCD is normal format. #0 1 The current channel's TCD specifies a scatter gather format. The DLASTSGA field provides a memory pointer to the next TCD to be loaded into this channel after the major loop completes its execution. #1 INTHALF Enable an interrupt when major counter is half complete. 2 1 read-write 0 The half-point interrupt is disabled #0 1 The half-point interrupt is enabled #1 INTMAJOR Enable an interrupt when major iteration count completes 1 1 read-write 0 The end-of-major loop interrupt is disabled #0 1 The end-of-major loop interrupt is enabled #1 MAJORELINK Enable channel-to-channel linking on major loop complete 5 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 MAJORLINKCH Link Channel Number 8 4 read-write START Channel Start 0 1 read-write 0 The channel is not explicitly started #0 1 The channel is explicitly started via a software initiated service request #1 TCD12_DADDR TCD Destination Address 0xEAA0 32 read-write n 0x0 0x0 DADDR Destination Address 0 32 read-write TCD12_DLASTSGA TCD Last Destination Address Adjustment/Scatter Gather Address 0xEB10 32 read-write n 0x0 0x0 DLASTSGA Destination last address adjustment or the memory address for the next transfer control descriptor to be loaded into this channel (scatter/gather) 0 32 read-write TCD12_DOFF TCD Signed Destination Address Offset 0xEAD8 16 read-write n 0x0 0x0 DOFF Destination Address Signed offset 0 16 read-write TCD12_NBYTES_MLNO TCD Minor Byte Count (Minor Loop Disabled) DMA 0xEA30 32 read-write n 0x0 0x0 NBYTES Minor Byte Transfer Count 0 32 read-write TCD12_NBYTES_MLOFFNO TCD Signed Minor Loop Offset (Minor Loop Enabled and Offset Disabled) DMA 0xEA30 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 NBYTES Minor Byte Transfer Count 0 30 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD12_NBYTES_MLOFFYES TCD Signed Minor Loop Offset (Minor Loop and Offset Enabled) DMA 0xEA30 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 MLOFF If SMLOE or DMLOE is set, this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes. 10 20 read-write NBYTES Minor Byte Transfer Count 0 10 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD12_SADDR TCD Source Address 0xE9C0 32 read-write n 0x0 0x0 SADDR Source Address 0 32 read-write TCD12_SLAST TCD Last Source Address Adjustment 0xEA68 32 read-write n 0x0 0x0 SLAST Last source Address Adjustment 0 32 read-write TCD12_SOFF TCD Signed Source Address Offset 0xE9F8 16 read-write n 0x0 0x0 SOFF Source address signed offset 0 16 read-write TCD13_ATTR TCD Transfer Attributes 0xFBBA 16 read-write n 0x0 0x0 DMOD Destination Address Modulo 3 5 read-write DSIZE Destination Data Transfer Size 0 3 read-write SMOD Source Address Modulo. 11 5 read-write 0 Source address modulo feature is disabled #00000 SSIZE Source data transfer size 8 3 read-write 000 8-bit #000 001 16-bit #001 010 32-bit #010 100 16-byte #100 101 32-byte #101 TCD13_BITER_ELINKNO TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0xFD22 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 15 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD13_BITER_ELINKYES TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0xFD22 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 9 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD13_CITER_ELINKNO TCD Current Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0xFCAA 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 15 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD13_CITER_ELINKYES TCD Current Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0xFCAA 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 9 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD13_CSR TCD Control and Status 0xFD04 16 read-write n 0x0 0x0 ACTIVE Channel Active 6 1 read-write BWC Bandwidth Control 14 2 read-write 00 No eDMA engine stalls #00 10 eDMA engine stalls for 4 cycles after each r/w #10 11 eDMA engine stalls for 8 cycles after each r/w #11 DONE Channel Done 7 1 read-write DREQ Disable Request 3 1 read-write 0 The channel's ERQ bit is not affected #0 1 The channel's ERQ bit is cleared when the major loop is complete #1 ESG Enable Scatter/Gather Processing 4 1 read-write 0 The current channel's TCD is normal format. #0 1 The current channel's TCD specifies a scatter gather format. The DLASTSGA field provides a memory pointer to the next TCD to be loaded into this channel after the major loop completes its execution. #1 INTHALF Enable an interrupt when major counter is half complete. 2 1 read-write 0 The half-point interrupt is disabled #0 1 The half-point interrupt is enabled #1 INTMAJOR Enable an interrupt when major iteration count completes 1 1 read-write 0 The end-of-major loop interrupt is disabled #0 1 The end-of-major loop interrupt is enabled #1 MAJORELINK Enable channel-to-channel linking on major loop complete 5 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 MAJORLINKCH Link Channel Number 8 4 read-write START Channel Start 0 1 read-write 0 The channel is not explicitly started #0 1 The channel is explicitly started via a software initiated service request #1 TCD13_DADDR TCD Destination Address 0xFC50 32 read-write n 0x0 0x0 DADDR Destination Address 0 32 read-write TCD13_DLASTSGA TCD Last Destination Address Adjustment/Scatter Gather Address 0xFCC8 32 read-write n 0x0 0x0 DLASTSGA Destination last address adjustment or the memory address for the next transfer control descriptor to be loaded into this channel (scatter/gather) 0 32 read-write TCD13_DOFF TCD Signed Destination Address Offset 0xFC8C 16 read-write n 0x0 0x0 DOFF Destination Address Signed offset 0 16 read-write TCD13_NBYTES_MLNO TCD Minor Byte Count (Minor Loop Disabled) DMA 0xFBD8 32 read-write n 0x0 0x0 NBYTES Minor Byte Transfer Count 0 32 read-write TCD13_NBYTES_MLOFFNO TCD Signed Minor Loop Offset (Minor Loop Enabled and Offset Disabled) DMA 0xFBD8 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 NBYTES Minor Byte Transfer Count 0 30 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD13_NBYTES_MLOFFYES TCD Signed Minor Loop Offset (Minor Loop and Offset Enabled) DMA 0xFBD8 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 MLOFF If SMLOE or DMLOE is set, this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes. 10 20 read-write NBYTES Minor Byte Transfer Count 0 10 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD13_SADDR TCD Source Address 0xFB60 32 read-write n 0x0 0x0 SADDR Source Address 0 32 read-write TCD13_SLAST TCD Last Source Address Adjustment 0xFC14 32 read-write n 0x0 0x0 SLAST Last source Address Adjustment 0 32 read-write TCD13_SOFF TCD Signed Source Address Offset 0xFB9C 16 read-write n 0x0 0x0 SOFF Source address signed offset 0 16 read-write TCD14_ATTR TCD Transfer Attributes 0x10D80 16 read-write n 0x0 0x0 DMOD Destination Address Modulo 3 5 read-write DSIZE Destination Data Transfer Size 0 3 read-write SMOD Source Address Modulo. 11 5 read-write 0 Source address modulo feature is disabled #00000 SSIZE Source data transfer size 8 3 read-write 000 8-bit #000 001 16-bit #001 010 32-bit #010 100 16-byte #100 101 32-byte #101 TCD14_BITER_ELINKNO TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x10F00 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 15 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD14_BITER_ELINKYES TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x10F00 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 9 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD14_CITER_ELINKNO TCD Current Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x10E80 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 15 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD14_CITER_ELINKYES TCD Current Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x10E80 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 9 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD14_CSR TCD Control and Status 0x10EE0 16 read-write n 0x0 0x0 ACTIVE Channel Active 6 1 read-write BWC Bandwidth Control 14 2 read-write 00 No eDMA engine stalls #00 10 eDMA engine stalls for 4 cycles after each r/w #10 11 eDMA engine stalls for 8 cycles after each r/w #11 DONE Channel Done 7 1 read-write DREQ Disable Request 3 1 read-write 0 The channel's ERQ bit is not affected #0 1 The channel's ERQ bit is cleared when the major loop is complete #1 ESG Enable Scatter/Gather Processing 4 1 read-write 0 The current channel's TCD is normal format. #0 1 The current channel's TCD specifies a scatter gather format. The DLASTSGA field provides a memory pointer to the next TCD to be loaded into this channel after the major loop completes its execution. #1 INTHALF Enable an interrupt when major counter is half complete. 2 1 read-write 0 The half-point interrupt is disabled #0 1 The half-point interrupt is enabled #1 INTMAJOR Enable an interrupt when major iteration count completes 1 1 read-write 0 The end-of-major loop interrupt is disabled #0 1 The end-of-major loop interrupt is enabled #1 MAJORELINK Enable channel-to-channel linking on major loop complete 5 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 MAJORLINKCH Link Channel Number 8 4 read-write START Channel Start 0 1 read-write 0 The channel is not explicitly started #0 1 The channel is explicitly started via a software initiated service request #1 TCD14_DADDR TCD Destination Address 0x10E20 32 read-write n 0x0 0x0 DADDR Destination Address 0 32 read-write TCD14_DLASTSGA TCD Last Destination Address Adjustment/Scatter Gather Address 0x10EA0 32 read-write n 0x0 0x0 DLASTSGA Destination last address adjustment or the memory address for the next transfer control descriptor to be loaded into this channel (scatter/gather) 0 32 read-write TCD14_DOFF TCD Signed Destination Address Offset 0x10E60 16 read-write n 0x0 0x0 DOFF Destination Address Signed offset 0 16 read-write TCD14_NBYTES_MLNO TCD Minor Byte Count (Minor Loop Disabled) DMA 0x10DA0 32 read-write n 0x0 0x0 NBYTES Minor Byte Transfer Count 0 32 read-write TCD14_NBYTES_MLOFFNO TCD Signed Minor Loop Offset (Minor Loop Enabled and Offset Disabled) DMA 0x10DA0 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 NBYTES Minor Byte Transfer Count 0 30 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD14_NBYTES_MLOFFYES TCD Signed Minor Loop Offset (Minor Loop and Offset Enabled) DMA 0x10DA0 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 MLOFF If SMLOE or DMLOE is set, this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes. 10 20 read-write NBYTES Minor Byte Transfer Count 0 10 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD14_SADDR TCD Source Address 0x10D20 32 read-write n 0x0 0x0 SADDR Source Address 0 32 read-write TCD14_SLAST TCD Last Source Address Adjustment 0x10DE0 32 read-write n 0x0 0x0 SLAST Last source Address Adjustment 0 32 read-write TCD14_SOFF TCD Signed Source Address Offset 0x10D60 16 read-write n 0x0 0x0 SOFF Source address signed offset 0 16 read-write TCD15_ATTR TCD Transfer Attributes 0x11F66 16 read-write n 0x0 0x0 DMOD Destination Address Modulo 3 5 read-write DSIZE Destination Data Transfer Size 0 3 read-write SMOD Source Address Modulo. 11 5 read-write 0 Source address modulo feature is disabled #00000 SSIZE Source data transfer size 8 3 read-write 000 8-bit #000 001 16-bit #001 010 32-bit #010 100 16-byte #100 101 32-byte #101 TCD15_BITER_ELINKNO TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x120FE 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 15 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD15_BITER_ELINKYES TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x120FE 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 9 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD15_CITER_ELINKNO TCD Current Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x12076 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 15 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD15_CITER_ELINKYES TCD Current Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x12076 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 9 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD15_CSR TCD Control and Status 0x120DC 16 read-write n 0x0 0x0 ACTIVE Channel Active 6 1 read-write BWC Bandwidth Control 14 2 read-write 00 No eDMA engine stalls #00 10 eDMA engine stalls for 4 cycles after each r/w #10 11 eDMA engine stalls for 8 cycles after each r/w #11 DONE Channel Done 7 1 read-write DREQ Disable Request 3 1 read-write 0 The channel's ERQ bit is not affected #0 1 The channel's ERQ bit is cleared when the major loop is complete #1 ESG Enable Scatter/Gather Processing 4 1 read-write 0 The current channel's TCD is normal format. #0 1 The current channel's TCD specifies a scatter gather format. The DLASTSGA field provides a memory pointer to the next TCD to be loaded into this channel after the major loop completes its execution. #1 INTHALF Enable an interrupt when major counter is half complete. 2 1 read-write 0 The half-point interrupt is disabled #0 1 The half-point interrupt is enabled #1 INTMAJOR Enable an interrupt when major iteration count completes 1 1 read-write 0 The end-of-major loop interrupt is disabled #0 1 The end-of-major loop interrupt is enabled #1 MAJORELINK Enable channel-to-channel linking on major loop complete 5 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 MAJORLINKCH Link Channel Number 8 4 read-write START Channel Start 0 1 read-write 0 The channel is not explicitly started #0 1 The channel is explicitly started via a software initiated service request #1 TCD15_DADDR TCD Destination Address 0x12010 32 read-write n 0x0 0x0 DADDR Destination Address 0 32 read-write TCD15_DLASTSGA TCD Last Destination Address Adjustment/Scatter Gather Address 0x12098 32 read-write n 0x0 0x0 DLASTSGA Destination last address adjustment or the memory address for the next transfer control descriptor to be loaded into this channel (scatter/gather) 0 32 read-write TCD15_DOFF TCD Signed Destination Address Offset 0x12054 16 read-write n 0x0 0x0 DOFF Destination Address Signed offset 0 16 read-write TCD15_NBYTES_MLNO TCD Minor Byte Count (Minor Loop Disabled) DMA 0x11F88 32 read-write n 0x0 0x0 NBYTES Minor Byte Transfer Count 0 32 read-write TCD15_NBYTES_MLOFFNO TCD Signed Minor Loop Offset (Minor Loop Enabled and Offset Disabled) DMA 0x11F88 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 NBYTES Minor Byte Transfer Count 0 30 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD15_NBYTES_MLOFFYES TCD Signed Minor Loop Offset (Minor Loop and Offset Enabled) DMA 0x11F88 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 MLOFF If SMLOE or DMLOE is set, this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes. 10 20 read-write NBYTES Minor Byte Transfer Count 0 10 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD15_SADDR TCD Source Address 0x11F00 32 read-write n 0x0 0x0 SADDR Source Address 0 32 read-write TCD15_SLAST TCD Last Source Address Adjustment 0x11FCC 32 read-write n 0x0 0x0 SLAST Last source Address Adjustment 0 32 read-write TCD15_SOFF TCD Signed Source Address Offset 0x11F44 16 read-write n 0x0 0x0 SOFF Source address signed offset 0 16 read-write TCD1_ATTR TCD Transfer Attributes 0x3032 16 read-write n 0x0 0x0 DMOD Destination Address Modulo 3 5 read-write DSIZE Destination Data Transfer Size 0 3 read-write SMOD Source Address Modulo. 11 5 read-write 0 Source address modulo feature is disabled #00000 SSIZE Source data transfer size 8 3 read-write 000 8-bit #000 001 16-bit #001 010 32-bit #010 100 16-byte #100 101 32-byte #101 TCD1_BITER_ELINKNO TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x307A 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 15 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD1_BITER_ELINKYES TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x307A 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 9 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD1_CITER_ELINKNO TCD Current Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x3062 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 15 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD1_CITER_ELINKYES TCD Current Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x3062 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 9 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD1_CSR TCD Control and Status 0x3074 16 read-write n 0x0 0x0 ACTIVE Channel Active 6 1 read-write BWC Bandwidth Control 14 2 read-write 00 No eDMA engine stalls #00 10 eDMA engine stalls for 4 cycles after each r/w #10 11 eDMA engine stalls for 8 cycles after each r/w #11 DONE Channel Done 7 1 read-write DREQ Disable Request 3 1 read-write 0 The channel's ERQ bit is not affected #0 1 The channel's ERQ bit is cleared when the major loop is complete #1 ESG Enable Scatter/Gather Processing 4 1 read-write 0 The current channel's TCD is normal format. #0 1 The current channel's TCD specifies a scatter gather format. The DLASTSGA field provides a memory pointer to the next TCD to be loaded into this channel after the major loop completes its execution. #1 INTHALF Enable an interrupt when major counter is half complete. 2 1 read-write 0 The half-point interrupt is disabled #0 1 The half-point interrupt is enabled #1 INTMAJOR Enable an interrupt when major iteration count completes 1 1 read-write 0 The end-of-major loop interrupt is disabled #0 1 The end-of-major loop interrupt is enabled #1 MAJORELINK Enable channel-to-channel linking on major loop complete 5 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 MAJORLINKCH Link Channel Number 8 4 read-write START Channel Start 0 1 read-write 0 The channel is not explicitly started #0 1 The channel is explicitly started via a software initiated service request #1 TCD1_DADDR TCD Destination Address 0x3050 32 read-write n 0x0 0x0 DADDR Destination Address 0 32 read-write TCD1_DLASTSGA TCD Last Destination Address Adjustment/Scatter Gather Address 0x3068 32 read-write n 0x0 0x0 DLASTSGA Destination last address adjustment or the memory address for the next transfer control descriptor to be loaded into this channel (scatter/gather) 0 32 read-write TCD1_DOFF TCD Signed Destination Address Offset 0x305C 16 read-write n 0x0 0x0 DOFF Destination Address Signed offset 0 16 read-write TCD1_NBYTES_MLNO TCD Minor Byte Count (Minor Loop Disabled) DMA 0x3038 32 read-write n 0x0 0x0 NBYTES Minor Byte Transfer Count 0 32 read-write TCD1_NBYTES_MLOFFNO TCD Signed Minor Loop Offset (Minor Loop Enabled and Offset Disabled) DMA 0x3038 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 NBYTES Minor Byte Transfer Count 0 30 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD1_NBYTES_MLOFFYES TCD Signed Minor Loop Offset (Minor Loop and Offset Enabled) DMA 0x3038 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 MLOFF If SMLOE or DMLOE is set, this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes. 10 20 read-write NBYTES Minor Byte Transfer Count 0 10 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD1_SADDR TCD Source Address 0x3020 32 read-write n 0x0 0x0 SADDR Source Address 0 32 read-write TCD1_SLAST TCD Last Source Address Adjustment 0x3044 32 read-write n 0x0 0x0 SLAST Last source Address Adjustment 0 32 read-write TCD1_SOFF TCD Signed Source Address Offset 0x302C 16 read-write n 0x0 0x0 SOFF Source address signed offset 0 16 read-write TCD2_ATTR TCD Transfer Attributes 0x4078 16 read-write n 0x0 0x0 DMOD Destination Address Modulo 3 5 read-write DSIZE Destination Data Transfer Size 0 3 read-write SMOD Source Address Modulo. 11 5 read-write 0 Source address modulo feature is disabled #00000 SSIZE Source data transfer size 8 3 read-write 000 8-bit #000 001 16-bit #001 010 32-bit #010 100 16-byte #100 101 32-byte #101 TCD2_BITER_ELINKNO TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x40D8 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 15 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD2_BITER_ELINKYES TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x40D8 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 9 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD2_CITER_ELINKNO TCD Current Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x40B8 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 15 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD2_CITER_ELINKYES TCD Current Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x40B8 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 9 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD2_CSR TCD Control and Status 0x40D0 16 read-write n 0x0 0x0 ACTIVE Channel Active 6 1 read-write BWC Bandwidth Control 14 2 read-write 00 No eDMA engine stalls #00 10 eDMA engine stalls for 4 cycles after each r/w #10 11 eDMA engine stalls for 8 cycles after each r/w #11 DONE Channel Done 7 1 read-write DREQ Disable Request 3 1 read-write 0 The channel's ERQ bit is not affected #0 1 The channel's ERQ bit is cleared when the major loop is complete #1 ESG Enable Scatter/Gather Processing 4 1 read-write 0 The current channel's TCD is normal format. #0 1 The current channel's TCD specifies a scatter gather format. The DLASTSGA field provides a memory pointer to the next TCD to be loaded into this channel after the major loop completes its execution. #1 INTHALF Enable an interrupt when major counter is half complete. 2 1 read-write 0 The half-point interrupt is disabled #0 1 The half-point interrupt is enabled #1 INTMAJOR Enable an interrupt when major iteration count completes 1 1 read-write 0 The end-of-major loop interrupt is disabled #0 1 The end-of-major loop interrupt is enabled #1 MAJORELINK Enable channel-to-channel linking on major loop complete 5 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 MAJORLINKCH Link Channel Number 8 4 read-write START Channel Start 0 1 read-write 0 The channel is not explicitly started #0 1 The channel is explicitly started via a software initiated service request #1 TCD2_DADDR TCD Destination Address 0x40A0 32 read-write n 0x0 0x0 DADDR Destination Address 0 32 read-write TCD2_DLASTSGA TCD Last Destination Address Adjustment/Scatter Gather Address 0x40C0 32 read-write n 0x0 0x0 DLASTSGA Destination last address adjustment or the memory address for the next transfer control descriptor to be loaded into this channel (scatter/gather) 0 32 read-write TCD2_DOFF TCD Signed Destination Address Offset 0x40B0 16 read-write n 0x0 0x0 DOFF Destination Address Signed offset 0 16 read-write TCD2_NBYTES_MLNO TCD Minor Byte Count (Minor Loop Disabled) DMA 0x4080 32 read-write n 0x0 0x0 NBYTES Minor Byte Transfer Count 0 32 read-write TCD2_NBYTES_MLOFFNO TCD Signed Minor Loop Offset (Minor Loop Enabled and Offset Disabled) DMA 0x4080 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 NBYTES Minor Byte Transfer Count 0 30 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD2_NBYTES_MLOFFYES TCD Signed Minor Loop Offset (Minor Loop and Offset Enabled) DMA 0x4080 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 MLOFF If SMLOE or DMLOE is set, this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes. 10 20 read-write NBYTES Minor Byte Transfer Count 0 10 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD2_SADDR TCD Source Address 0x4060 32 read-write n 0x0 0x0 SADDR Source Address 0 32 read-write TCD2_SLAST TCD Last Source Address Adjustment 0x4090 32 read-write n 0x0 0x0 SLAST Last source Address Adjustment 0 32 read-write TCD2_SOFF TCD Signed Source Address Offset 0x4070 16 read-write n 0x0 0x0 SOFF Source address signed offset 0 16 read-write TCD3_ATTR TCD Transfer Attributes 0x50DE 16 read-write n 0x0 0x0 DMOD Destination Address Modulo 3 5 read-write DSIZE Destination Data Transfer Size 0 3 read-write SMOD Source Address Modulo. 11 5 read-write 0 Source address modulo feature is disabled #00000 SSIZE Source data transfer size 8 3 read-write 000 8-bit #000 001 16-bit #001 010 32-bit #010 100 16-byte #100 101 32-byte #101 TCD3_BITER_ELINKNO TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x5156 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 15 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD3_BITER_ELINKYES TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x5156 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 9 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD3_CITER_ELINKNO TCD Current Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x512E 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 15 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD3_CITER_ELINKYES TCD Current Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x512E 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 9 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD3_CSR TCD Control and Status 0x514C 16 read-write n 0x0 0x0 ACTIVE Channel Active 6 1 read-write BWC Bandwidth Control 14 2 read-write 00 No eDMA engine stalls #00 10 eDMA engine stalls for 4 cycles after each r/w #10 11 eDMA engine stalls for 8 cycles after each r/w #11 DONE Channel Done 7 1 read-write DREQ Disable Request 3 1 read-write 0 The channel's ERQ bit is not affected #0 1 The channel's ERQ bit is cleared when the major loop is complete #1 ESG Enable Scatter/Gather Processing 4 1 read-write 0 The current channel's TCD is normal format. #0 1 The current channel's TCD specifies a scatter gather format. The DLASTSGA field provides a memory pointer to the next TCD to be loaded into this channel after the major loop completes its execution. #1 INTHALF Enable an interrupt when major counter is half complete. 2 1 read-write 0 The half-point interrupt is disabled #0 1 The half-point interrupt is enabled #1 INTMAJOR Enable an interrupt when major iteration count completes 1 1 read-write 0 The end-of-major loop interrupt is disabled #0 1 The end-of-major loop interrupt is enabled #1 MAJORELINK Enable channel-to-channel linking on major loop complete 5 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 MAJORLINKCH Link Channel Number 8 4 read-write START Channel Start 0 1 read-write 0 The channel is not explicitly started #0 1 The channel is explicitly started via a software initiated service request #1 TCD3_DADDR TCD Destination Address 0x5110 32 read-write n 0x0 0x0 DADDR Destination Address 0 32 read-write TCD3_DLASTSGA TCD Last Destination Address Adjustment/Scatter Gather Address 0x5138 32 read-write n 0x0 0x0 DLASTSGA Destination last address adjustment or the memory address for the next transfer control descriptor to be loaded into this channel (scatter/gather) 0 32 read-write TCD3_DOFF TCD Signed Destination Address Offset 0x5124 16 read-write n 0x0 0x0 DOFF Destination Address Signed offset 0 16 read-write TCD3_NBYTES_MLNO TCD Minor Byte Count (Minor Loop Disabled) DMA 0x50E8 32 read-write n 0x0 0x0 NBYTES Minor Byte Transfer Count 0 32 read-write TCD3_NBYTES_MLOFFNO TCD Signed Minor Loop Offset (Minor Loop Enabled and Offset Disabled) DMA 0x50E8 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 NBYTES Minor Byte Transfer Count 0 30 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD3_NBYTES_MLOFFYES TCD Signed Minor Loop Offset (Minor Loop and Offset Enabled) DMA 0x50E8 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 MLOFF If SMLOE or DMLOE is set, this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes. 10 20 read-write NBYTES Minor Byte Transfer Count 0 10 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD3_SADDR TCD Source Address 0x50C0 32 read-write n 0x0 0x0 SADDR Source Address 0 32 read-write TCD3_SLAST TCD Last Source Address Adjustment 0x50FC 32 read-write n 0x0 0x0 SLAST Last source Address Adjustment 0 32 read-write TCD3_SOFF TCD Signed Source Address Offset 0x50D4 16 read-write n 0x0 0x0 SOFF Source address signed offset 0 16 read-write TCD4_ATTR TCD Transfer Attributes 0x6164 16 read-write n 0x0 0x0 DMOD Destination Address Modulo 3 5 read-write DSIZE Destination Data Transfer Size 0 3 read-write SMOD Source Address Modulo. 11 5 read-write 0 Source address modulo feature is disabled #00000 SSIZE Source data transfer size 8 3 read-write 000 8-bit #000 001 16-bit #001 010 32-bit #010 100 16-byte #100 101 32-byte #101 TCD4_BITER_ELINKNO TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x61F4 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 15 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD4_BITER_ELINKYES TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x61F4 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 9 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD4_CITER_ELINKNO TCD Current Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x61C4 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 15 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD4_CITER_ELINKYES TCD Current Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x61C4 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 9 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD4_CSR TCD Control and Status 0x61E8 16 read-write n 0x0 0x0 ACTIVE Channel Active 6 1 read-write BWC Bandwidth Control 14 2 read-write 00 No eDMA engine stalls #00 10 eDMA engine stalls for 4 cycles after each r/w #10 11 eDMA engine stalls for 8 cycles after each r/w #11 DONE Channel Done 7 1 read-write DREQ Disable Request 3 1 read-write 0 The channel's ERQ bit is not affected #0 1 The channel's ERQ bit is cleared when the major loop is complete #1 ESG Enable Scatter/Gather Processing 4 1 read-write 0 The current channel's TCD is normal format. #0 1 The current channel's TCD specifies a scatter gather format. The DLASTSGA field provides a memory pointer to the next TCD to be loaded into this channel after the major loop completes its execution. #1 INTHALF Enable an interrupt when major counter is half complete. 2 1 read-write 0 The half-point interrupt is disabled #0 1 The half-point interrupt is enabled #1 INTMAJOR Enable an interrupt when major iteration count completes 1 1 read-write 0 The end-of-major loop interrupt is disabled #0 1 The end-of-major loop interrupt is enabled #1 MAJORELINK Enable channel-to-channel linking on major loop complete 5 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 MAJORLINKCH Link Channel Number 8 4 read-write START Channel Start 0 1 read-write 0 The channel is not explicitly started #0 1 The channel is explicitly started via a software initiated service request #1 TCD4_DADDR TCD Destination Address 0x61A0 32 read-write n 0x0 0x0 DADDR Destination Address 0 32 read-write TCD4_DLASTSGA TCD Last Destination Address Adjustment/Scatter Gather Address 0x61D0 32 read-write n 0x0 0x0 DLASTSGA Destination last address adjustment or the memory address for the next transfer control descriptor to be loaded into this channel (scatter/gather) 0 32 read-write TCD4_DOFF TCD Signed Destination Address Offset 0x61B8 16 read-write n 0x0 0x0 DOFF Destination Address Signed offset 0 16 read-write TCD4_NBYTES_MLNO TCD Minor Byte Count (Minor Loop Disabled) DMA 0x6170 32 read-write n 0x0 0x0 NBYTES Minor Byte Transfer Count 0 32 read-write TCD4_NBYTES_MLOFFNO TCD Signed Minor Loop Offset (Minor Loop Enabled and Offset Disabled) DMA 0x6170 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 NBYTES Minor Byte Transfer Count 0 30 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD4_NBYTES_MLOFFYES TCD Signed Minor Loop Offset (Minor Loop and Offset Enabled) DMA 0x6170 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 MLOFF If SMLOE or DMLOE is set, this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes. 10 20 read-write NBYTES Minor Byte Transfer Count 0 10 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD4_SADDR TCD Source Address 0x6140 32 read-write n 0x0 0x0 SADDR Source Address 0 32 read-write TCD4_SLAST TCD Last Source Address Adjustment 0x6188 32 read-write n 0x0 0x0 SLAST Last source Address Adjustment 0 32 read-write TCD4_SOFF TCD Signed Source Address Offset 0x6158 16 read-write n 0x0 0x0 SOFF Source address signed offset 0 16 read-write TCD5_ATTR TCD Transfer Attributes 0x720A 16 read-write n 0x0 0x0 DMOD Destination Address Modulo 3 5 read-write DSIZE Destination Data Transfer Size 0 3 read-write SMOD Source Address Modulo. 11 5 read-write 0 Source address modulo feature is disabled #00000 SSIZE Source data transfer size 8 3 read-write 000 8-bit #000 001 16-bit #001 010 32-bit #010 100 16-byte #100 101 32-byte #101 TCD5_BITER_ELINKNO TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x72B2 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 15 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD5_BITER_ELINKYES TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x72B2 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 9 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD5_CITER_ELINKNO TCD Current Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x727A 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 15 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD5_CITER_ELINKYES TCD Current Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x727A 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 9 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD5_CSR TCD Control and Status 0x72A4 16 read-write n 0x0 0x0 ACTIVE Channel Active 6 1 read-write BWC Bandwidth Control 14 2 read-write 00 No eDMA engine stalls #00 10 eDMA engine stalls for 4 cycles after each r/w #10 11 eDMA engine stalls for 8 cycles after each r/w #11 DONE Channel Done 7 1 read-write DREQ Disable Request 3 1 read-write 0 The channel's ERQ bit is not affected #0 1 The channel's ERQ bit is cleared when the major loop is complete #1 ESG Enable Scatter/Gather Processing 4 1 read-write 0 The current channel's TCD is normal format. #0 1 The current channel's TCD specifies a scatter gather format. The DLASTSGA field provides a memory pointer to the next TCD to be loaded into this channel after the major loop completes its execution. #1 INTHALF Enable an interrupt when major counter is half complete. 2 1 read-write 0 The half-point interrupt is disabled #0 1 The half-point interrupt is enabled #1 INTMAJOR Enable an interrupt when major iteration count completes 1 1 read-write 0 The end-of-major loop interrupt is disabled #0 1 The end-of-major loop interrupt is enabled #1 MAJORELINK Enable channel-to-channel linking on major loop complete 5 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 MAJORLINKCH Link Channel Number 8 4 read-write START Channel Start 0 1 read-write 0 The channel is not explicitly started #0 1 The channel is explicitly started via a software initiated service request #1 TCD5_DADDR TCD Destination Address 0x7250 32 read-write n 0x0 0x0 DADDR Destination Address 0 32 read-write TCD5_DLASTSGA TCD Last Destination Address Adjustment/Scatter Gather Address 0x7288 32 read-write n 0x0 0x0 DLASTSGA Destination last address adjustment or the memory address for the next transfer control descriptor to be loaded into this channel (scatter/gather) 0 32 read-write TCD5_DOFF TCD Signed Destination Address Offset 0x726C 16 read-write n 0x0 0x0 DOFF Destination Address Signed offset 0 16 read-write TCD5_NBYTES_MLNO TCD Minor Byte Count (Minor Loop Disabled) DMA 0x7218 32 read-write n 0x0 0x0 NBYTES Minor Byte Transfer Count 0 32 read-write TCD5_NBYTES_MLOFFNO TCD Signed Minor Loop Offset (Minor Loop Enabled and Offset Disabled) DMA 0x7218 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 NBYTES Minor Byte Transfer Count 0 30 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD5_NBYTES_MLOFFYES TCD Signed Minor Loop Offset (Minor Loop and Offset Enabled) DMA 0x7218 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 MLOFF If SMLOE or DMLOE is set, this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes. 10 20 read-write NBYTES Minor Byte Transfer Count 0 10 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD5_SADDR TCD Source Address 0x71E0 32 read-write n 0x0 0x0 SADDR Source Address 0 32 read-write TCD5_SLAST TCD Last Source Address Adjustment 0x7234 32 read-write n 0x0 0x0 SLAST Last source Address Adjustment 0 32 read-write TCD5_SOFF TCD Signed Source Address Offset 0x71FC 16 read-write n 0x0 0x0 SOFF Source address signed offset 0 16 read-write TCD6_ATTR TCD Transfer Attributes 0x82D0 16 read-write n 0x0 0x0 DMOD Destination Address Modulo 3 5 read-write DSIZE Destination Data Transfer Size 0 3 read-write SMOD Source Address Modulo. 11 5 read-write 0 Source address modulo feature is disabled #00000 SSIZE Source data transfer size 8 3 read-write 000 8-bit #000 001 16-bit #001 010 32-bit #010 100 16-byte #100 101 32-byte #101 TCD6_BITER_ELINKNO TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x8390 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 15 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD6_BITER_ELINKYES TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x8390 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 9 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD6_CITER_ELINKNO TCD Current Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x8350 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 15 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD6_CITER_ELINKYES TCD Current Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x8350 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 9 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD6_CSR TCD Control and Status 0x8380 16 read-write n 0x0 0x0 ACTIVE Channel Active 6 1 read-write BWC Bandwidth Control 14 2 read-write 00 No eDMA engine stalls #00 10 eDMA engine stalls for 4 cycles after each r/w #10 11 eDMA engine stalls for 8 cycles after each r/w #11 DONE Channel Done 7 1 read-write DREQ Disable Request 3 1 read-write 0 The channel's ERQ bit is not affected #0 1 The channel's ERQ bit is cleared when the major loop is complete #1 ESG Enable Scatter/Gather Processing 4 1 read-write 0 The current channel's TCD is normal format. #0 1 The current channel's TCD specifies a scatter gather format. The DLASTSGA field provides a memory pointer to the next TCD to be loaded into this channel after the major loop completes its execution. #1 INTHALF Enable an interrupt when major counter is half complete. 2 1 read-write 0 The half-point interrupt is disabled #0 1 The half-point interrupt is enabled #1 INTMAJOR Enable an interrupt when major iteration count completes 1 1 read-write 0 The end-of-major loop interrupt is disabled #0 1 The end-of-major loop interrupt is enabled #1 MAJORELINK Enable channel-to-channel linking on major loop complete 5 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 MAJORLINKCH Link Channel Number 8 4 read-write START Channel Start 0 1 read-write 0 The channel is not explicitly started #0 1 The channel is explicitly started via a software initiated service request #1 TCD6_DADDR TCD Destination Address 0x8320 32 read-write n 0x0 0x0 DADDR Destination Address 0 32 read-write TCD6_DLASTSGA TCD Last Destination Address Adjustment/Scatter Gather Address 0x8360 32 read-write n 0x0 0x0 DLASTSGA Destination last address adjustment or the memory address for the next transfer control descriptor to be loaded into this channel (scatter/gather) 0 32 read-write TCD6_DOFF TCD Signed Destination Address Offset 0x8340 16 read-write n 0x0 0x0 DOFF Destination Address Signed offset 0 16 read-write TCD6_NBYTES_MLNO TCD Minor Byte Count (Minor Loop Disabled) DMA 0x82E0 32 read-write n 0x0 0x0 NBYTES Minor Byte Transfer Count 0 32 read-write TCD6_NBYTES_MLOFFNO TCD Signed Minor Loop Offset (Minor Loop Enabled and Offset Disabled) DMA 0x82E0 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 NBYTES Minor Byte Transfer Count 0 30 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD6_NBYTES_MLOFFYES TCD Signed Minor Loop Offset (Minor Loop and Offset Enabled) DMA 0x82E0 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 MLOFF If SMLOE or DMLOE is set, this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes. 10 20 read-write NBYTES Minor Byte Transfer Count 0 10 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD6_SADDR TCD Source Address 0x82A0 32 read-write n 0x0 0x0 SADDR Source Address 0 32 read-write TCD6_SLAST TCD Last Source Address Adjustment 0x8300 32 read-write n 0x0 0x0 SLAST Last source Address Adjustment 0 32 read-write TCD6_SOFF TCD Signed Source Address Offset 0x82C0 16 read-write n 0x0 0x0 SOFF Source address signed offset 0 16 read-write TCD7_ATTR TCD Transfer Attributes 0x93B6 16 read-write n 0x0 0x0 DMOD Destination Address Modulo 3 5 read-write DSIZE Destination Data Transfer Size 0 3 read-write SMOD Source Address Modulo. 11 5 read-write 0 Source address modulo feature is disabled #00000 SSIZE Source data transfer size 8 3 read-write 000 8-bit #000 001 16-bit #001 010 32-bit #010 100 16-byte #100 101 32-byte #101 TCD7_BITER_ELINKNO TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x948E 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 15 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD7_BITER_ELINKYES TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x948E 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 9 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD7_CITER_ELINKNO TCD Current Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0x9446 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 15 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD7_CITER_ELINKYES TCD Current Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0x9446 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 9 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD7_CSR TCD Control and Status 0x947C 16 read-write n 0x0 0x0 ACTIVE Channel Active 6 1 read-write BWC Bandwidth Control 14 2 read-write 00 No eDMA engine stalls #00 10 eDMA engine stalls for 4 cycles after each r/w #10 11 eDMA engine stalls for 8 cycles after each r/w #11 DONE Channel Done 7 1 read-write DREQ Disable Request 3 1 read-write 0 The channel's ERQ bit is not affected #0 1 The channel's ERQ bit is cleared when the major loop is complete #1 ESG Enable Scatter/Gather Processing 4 1 read-write 0 The current channel's TCD is normal format. #0 1 The current channel's TCD specifies a scatter gather format. The DLASTSGA field provides a memory pointer to the next TCD to be loaded into this channel after the major loop completes its execution. #1 INTHALF Enable an interrupt when major counter is half complete. 2 1 read-write 0 The half-point interrupt is disabled #0 1 The half-point interrupt is enabled #1 INTMAJOR Enable an interrupt when major iteration count completes 1 1 read-write 0 The end-of-major loop interrupt is disabled #0 1 The end-of-major loop interrupt is enabled #1 MAJORELINK Enable channel-to-channel linking on major loop complete 5 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 MAJORLINKCH Link Channel Number 8 4 read-write START Channel Start 0 1 read-write 0 The channel is not explicitly started #0 1 The channel is explicitly started via a software initiated service request #1 TCD7_DADDR TCD Destination Address 0x9410 32 read-write n 0x0 0x0 DADDR Destination Address 0 32 read-write TCD7_DLASTSGA TCD Last Destination Address Adjustment/Scatter Gather Address 0x9458 32 read-write n 0x0 0x0 DLASTSGA Destination last address adjustment or the memory address for the next transfer control descriptor to be loaded into this channel (scatter/gather) 0 32 read-write TCD7_DOFF TCD Signed Destination Address Offset 0x9434 16 read-write n 0x0 0x0 DOFF Destination Address Signed offset 0 16 read-write TCD7_NBYTES_MLNO TCD Minor Byte Count (Minor Loop Disabled) DMA 0x93C8 32 read-write n 0x0 0x0 NBYTES Minor Byte Transfer Count 0 32 read-write TCD7_NBYTES_MLOFFNO TCD Signed Minor Loop Offset (Minor Loop Enabled and Offset Disabled) DMA 0x93C8 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 NBYTES Minor Byte Transfer Count 0 30 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD7_NBYTES_MLOFFYES TCD Signed Minor Loop Offset (Minor Loop and Offset Enabled) DMA 0x93C8 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 MLOFF If SMLOE or DMLOE is set, this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes. 10 20 read-write NBYTES Minor Byte Transfer Count 0 10 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD7_SADDR TCD Source Address 0x9380 32 read-write n 0x0 0x0 SADDR Source Address 0 32 read-write TCD7_SLAST TCD Last Source Address Adjustment 0x93EC 32 read-write n 0x0 0x0 SLAST Last source Address Adjustment 0 32 read-write TCD7_SOFF TCD Signed Source Address Offset 0x93A4 16 read-write n 0x0 0x0 SOFF Source address signed offset 0 16 read-write TCD8_ATTR TCD Transfer Attributes 0xA4BC 16 read-write n 0x0 0x0 DMOD Destination Address Modulo 3 5 read-write DSIZE Destination Data Transfer Size 0 3 read-write SMOD Source Address Modulo. 11 5 read-write 0 Source address modulo feature is disabled #00000 SSIZE Source data transfer size 8 3 read-write 000 8-bit #000 001 16-bit #001 010 32-bit #010 100 16-byte #100 101 32-byte #101 TCD8_BITER_ELINKNO TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0xA5AC 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 15 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD8_BITER_ELINKYES TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0xA5AC 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 9 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD8_CITER_ELINKNO TCD Current Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0xA55C 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 15 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD8_CITER_ELINKYES TCD Current Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0xA55C 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 9 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD8_CSR TCD Control and Status 0xA598 16 read-write n 0x0 0x0 ACTIVE Channel Active 6 1 read-write BWC Bandwidth Control 14 2 read-write 00 No eDMA engine stalls #00 10 eDMA engine stalls for 4 cycles after each r/w #10 11 eDMA engine stalls for 8 cycles after each r/w #11 DONE Channel Done 7 1 read-write DREQ Disable Request 3 1 read-write 0 The channel's ERQ bit is not affected #0 1 The channel's ERQ bit is cleared when the major loop is complete #1 ESG Enable Scatter/Gather Processing 4 1 read-write 0 The current channel's TCD is normal format. #0 1 The current channel's TCD specifies a scatter gather format. The DLASTSGA field provides a memory pointer to the next TCD to be loaded into this channel after the major loop completes its execution. #1 INTHALF Enable an interrupt when major counter is half complete. 2 1 read-write 0 The half-point interrupt is disabled #0 1 The half-point interrupt is enabled #1 INTMAJOR Enable an interrupt when major iteration count completes 1 1 read-write 0 The end-of-major loop interrupt is disabled #0 1 The end-of-major loop interrupt is enabled #1 MAJORELINK Enable channel-to-channel linking on major loop complete 5 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 MAJORLINKCH Link Channel Number 8 4 read-write START Channel Start 0 1 read-write 0 The channel is not explicitly started #0 1 The channel is explicitly started via a software initiated service request #1 TCD8_DADDR TCD Destination Address 0xA520 32 read-write n 0x0 0x0 DADDR Destination Address 0 32 read-write TCD8_DLASTSGA TCD Last Destination Address Adjustment/Scatter Gather Address 0xA570 32 read-write n 0x0 0x0 DLASTSGA Destination last address adjustment or the memory address for the next transfer control descriptor to be loaded into this channel (scatter/gather) 0 32 read-write TCD8_DOFF TCD Signed Destination Address Offset 0xA548 16 read-write n 0x0 0x0 DOFF Destination Address Signed offset 0 16 read-write TCD8_NBYTES_MLNO TCD Minor Byte Count (Minor Loop Disabled) DMA 0xA4D0 32 read-write n 0x0 0x0 NBYTES Minor Byte Transfer Count 0 32 read-write TCD8_NBYTES_MLOFFNO TCD Signed Minor Loop Offset (Minor Loop Enabled and Offset Disabled) DMA 0xA4D0 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 NBYTES Minor Byte Transfer Count 0 30 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD8_NBYTES_MLOFFYES TCD Signed Minor Loop Offset (Minor Loop and Offset Enabled) DMA 0xA4D0 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 MLOFF If SMLOE or DMLOE is set, this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes. 10 20 read-write NBYTES Minor Byte Transfer Count 0 10 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD8_SADDR TCD Source Address 0xA480 32 read-write n 0x0 0x0 SADDR Source Address 0 32 read-write TCD8_SLAST TCD Last Source Address Adjustment 0xA4F8 32 read-write n 0x0 0x0 SLAST Last source Address Adjustment 0 32 read-write TCD8_SOFF TCD Signed Source Address Offset 0xA4A8 16 read-write n 0x0 0x0 SOFF Source address signed offset 0 16 read-write TCD9_ATTR TCD Transfer Attributes 0xB5E2 16 read-write n 0x0 0x0 DMOD Destination Address Modulo 3 5 read-write DSIZE Destination Data Transfer Size 0 3 read-write SMOD Source Address Modulo. 11 5 read-write 0 Source address modulo feature is disabled #00000 SSIZE Source data transfer size 8 3 read-write 000 8-bit #000 001 16-bit #001 010 32-bit #010 100 16-byte #100 101 32-byte #101 TCD9_BITER_ELINKNO TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0xB6EA 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 15 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD9_BITER_ELINKYES TCD Beginning Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0xB6EA 16 read-write n 0x0 0x0 BITER Starting Major Iteration Count 0 9 read-write ELINK Enables channel-to-channel linking on minor loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD9_CITER_ELINKNO TCD Current Minor Loop Link, Major Loop Count (Channel Linking Disabled) DMA 0xB692 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 15 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 TCD9_CITER_ELINKYES TCD Current Minor Loop Link, Major Loop Count (Channel Linking Enabled) DMA 0xB692 16 read-write n 0x0 0x0 CITER Current Major Iteration Count 0 9 read-write ELINK Enable channel-to-channel linking on minor-loop complete 15 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 LINKCH Link Channel Number 9 4 read-write TCD9_CSR TCD Control and Status 0xB6D4 16 read-write n 0x0 0x0 ACTIVE Channel Active 6 1 read-write BWC Bandwidth Control 14 2 read-write 00 No eDMA engine stalls #00 10 eDMA engine stalls for 4 cycles after each r/w #10 11 eDMA engine stalls for 8 cycles after each r/w #11 DONE Channel Done 7 1 read-write DREQ Disable Request 3 1 read-write 0 The channel's ERQ bit is not affected #0 1 The channel's ERQ bit is cleared when the major loop is complete #1 ESG Enable Scatter/Gather Processing 4 1 read-write 0 The current channel's TCD is normal format. #0 1 The current channel's TCD specifies a scatter gather format. The DLASTSGA field provides a memory pointer to the next TCD to be loaded into this channel after the major loop completes its execution. #1 INTHALF Enable an interrupt when major counter is half complete. 2 1 read-write 0 The half-point interrupt is disabled #0 1 The half-point interrupt is enabled #1 INTMAJOR Enable an interrupt when major iteration count completes 1 1 read-write 0 The end-of-major loop interrupt is disabled #0 1 The end-of-major loop interrupt is enabled #1 MAJORELINK Enable channel-to-channel linking on major loop complete 5 1 read-write 0 The channel-to-channel linking is disabled #0 1 The channel-to-channel linking is enabled #1 MAJORLINKCH Link Channel Number 8 4 read-write START Channel Start 0 1 read-write 0 The channel is not explicitly started #0 1 The channel is explicitly started via a software initiated service request #1 TCD9_DADDR TCD Destination Address 0xB650 32 read-write n 0x0 0x0 DADDR Destination Address 0 32 read-write TCD9_DLASTSGA TCD Last Destination Address Adjustment/Scatter Gather Address 0xB6A8 32 read-write n 0x0 0x0 DLASTSGA Destination last address adjustment or the memory address for the next transfer control descriptor to be loaded into this channel (scatter/gather) 0 32 read-write TCD9_DOFF TCD Signed Destination Address Offset 0xB67C 16 read-write n 0x0 0x0 DOFF Destination Address Signed offset 0 16 read-write TCD9_NBYTES_MLNO TCD Minor Byte Count (Minor Loop Disabled) DMA 0xB5F8 32 read-write n 0x0 0x0 NBYTES Minor Byte Transfer Count 0 32 read-write TCD9_NBYTES_MLOFFNO TCD Signed Minor Loop Offset (Minor Loop Enabled and Offset Disabled) DMA 0xB5F8 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 NBYTES Minor Byte Transfer Count 0 30 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD9_NBYTES_MLOFFYES TCD Signed Minor Loop Offset (Minor Loop and Offset Enabled) DMA 0xB5F8 32 read-write n 0x0 0x0 DMLOE Destination Minor Loop Offset enable 30 1 read-write 0 The minor loop offset is not applied to the DADDR #0 1 The minor loop offset is applied to the DADDR #1 MLOFF If SMLOE or DMLOE is set, this field represents a sign-extended offset applied to the source or destination address to form the next-state value after the minor loop completes. 10 20 read-write NBYTES Minor Byte Transfer Count 0 10 read-write SMLOE Source Minor Loop Offset Enable 31 1 read-write 0 The minor loop offset is not applied to the SADDR #0 1 The minor loop offset is applied to the SADDR #1 TCD9_SADDR TCD Source Address 0xB5A0 32 read-write n 0x0 0x0 SADDR Source Address 0 32 read-write TCD9_SLAST TCD Last Source Address Adjustment 0xB624 32 read-write n 0x0 0x0 SLAST Last source Address Adjustment 0 32 read-write TCD9_SOFF TCD Signed Source Address Offset 0xB5CC 16 read-write n 0x0 0x0 SOFF Source address signed offset 0 16 read-write DMAMUX DMA channel multiplexor DMAMUX 0x0 0x0 0x10 registers n CHCFG0 Channel Configuration register 0x0 8 read-write n 0x0 0x0 ENBL DMA Channel Enable 7 1 read-write 0 DMA channel is disabled. This mode is primarily used during configuration of the DMAMux. The DMA has separate channel enables/disables, which should be used to disable or reconfigure a DMA channel. #0 1 DMA channel is enabled #1 SOURCE DMA Channel Source (Slot) 0 6 read-write 0 Disable_Signal #0 2 UART0_Rx_Signal #10 4 UART1_Rx_Signal #100 16 SPI1_Signal #10000 32 FTM3_Channel0_Signal #100000 33 FTM3_Channel1_Signal #100001 34 FTM3_Channel2_Signal #100010 35 FTM3_Channel3_Signal #100011 18 I2C0_Signal #10010 36 FTM3_Channel4_Signal #100100 37 FTM3_Channel5_Signal #100101 19 I2C1_Signal #10011 38 FTM3_Channel6_Signal #100110 39 FTM3_Channel7_Signal #100111 5 UART1_Tx_Signal #101 20 FTM0_Channel0_Signal #10100 40 ADC0_Signal #101000 41 ADC1_Signal #101001 21 FTM0_Channel1_Signal #10101 42 CMP0_Signal #101010 43 CMP1_Signal #101011 22 FTM0_Channel2_Signal #10110 45 DAC0_Signal #101101 23 FTM0_Channel3_Signal #10111 46 DAC1_Signal #101110 3 UART0_Tx_Signal #11 6 UART2_Rx_Signal #110 12 I2S0_Rx_Signal #1100 24 FTM0_Channel4_Signal #11000 48 PDB_Signal #110000 49 PortA_Signal #110001 25 FTM0_Channel5_Signal #11001 50 PortB_Signal #110010 51 PortC_Signal #110011 13 I2S0_Tx_Signal #1101 26 FTM0_Channel6_Signal #11010 52 PortD_Signal #110100 53 PortE_Signal #110101 27 FTM0_Channel7_Signal #11011 7 UART2_Tx_Signal #111 14 SPI0_Rx_Signal #1110 28 FTM1_Channel0_Signal #11100 29 FTM1_Channel1_Signal #11101 58 LPUART0_Rx_Signal #111010 59 LPUART0_Tx_Signal #111011 15 SPI0_Tx_Signal #1111 30 FTM2_Channel0_Signal #11110 60 AlwaysOn60_Signal #111100 61 AlwaysOn61_Signal #111101 31 FTM2_Channel1_Signal #11111 62 AlwaysOn62_Signal #111110 63 AlwaysOn63_Signal #111111 TRIG DMA Channel Trigger Enable 6 1 read-write 0 Triggering is disabled. If triggering is disabled and ENBL is set, the DMA Channel will simply route the specified source to the DMA channel. (Normal mode) #0 1 Triggering is enabled. If triggering is enabled and ENBL is set, the DMAMUX is in Periodic Trigger mode. #1 CHCFG1 Channel Configuration register 0x1 8 read-write n 0x0 0x0 ENBL DMA Channel Enable 7 1 read-write 0 DMA channel is disabled. This mode is primarily used during configuration of the DMAMux. The DMA has separate channel enables/disables, which should be used to disable or reconfigure a DMA channel. #0 1 DMA channel is enabled #1 SOURCE DMA Channel Source (Slot) 0 6 read-write 0 Disable_Signal #0 2 UART0_Rx_Signal #10 4 UART1_Rx_Signal #100 16 SPI1_Signal #10000 32 FTM3_Channel0_Signal #100000 33 FTM3_Channel1_Signal #100001 34 FTM3_Channel2_Signal #100010 35 FTM3_Channel3_Signal #100011 18 I2C0_Signal #10010 36 FTM3_Channel4_Signal #100100 37 FTM3_Channel5_Signal #100101 19 I2C1_Signal #10011 38 FTM3_Channel6_Signal #100110 39 FTM3_Channel7_Signal #100111 5 UART1_Tx_Signal #101 20 FTM0_Channel0_Signal #10100 40 ADC0_Signal #101000 41 ADC1_Signal #101001 21 FTM0_Channel1_Signal #10101 42 CMP0_Signal #101010 43 CMP1_Signal #101011 22 FTM0_Channel2_Signal #10110 45 DAC0_Signal #101101 23 FTM0_Channel3_Signal #10111 46 DAC1_Signal #101110 3 UART0_Tx_Signal #11 6 UART2_Rx_Signal #110 12 I2S0_Rx_Signal #1100 24 FTM0_Channel4_Signal #11000 48 PDB_Signal #110000 49 PortA_Signal #110001 25 FTM0_Channel5_Signal #11001 50 PortB_Signal #110010 51 PortC_Signal #110011 13 I2S0_Tx_Signal #1101 26 FTM0_Channel6_Signal #11010 52 PortD_Signal #110100 53 PortE_Signal #110101 27 FTM0_Channel7_Signal #11011 7 UART2_Tx_Signal #111 14 SPI0_Rx_Signal #1110 28 FTM1_Channel0_Signal #11100 29 FTM1_Channel1_Signal #11101 58 LPUART0_Rx_Signal #111010 59 LPUART0_Tx_Signal #111011 15 SPI0_Tx_Signal #1111 30 FTM2_Channel0_Signal #11110 60 AlwaysOn60_Signal #111100 61 AlwaysOn61_Signal #111101 31 FTM2_Channel1_Signal #11111 62 AlwaysOn62_Signal #111110 63 AlwaysOn63_Signal #111111 TRIG DMA Channel Trigger Enable 6 1 read-write 0 Triggering is disabled. If triggering is disabled and ENBL is set, the DMA Channel will simply route the specified source to the DMA channel. (Normal mode) #0 1 Triggering is enabled. If triggering is enabled and ENBL is set, the DMAMUX is in Periodic Trigger mode. #1 CHCFG10 Channel Configuration register 0x37 8 read-write n 0x0 0x0 ENBL DMA Channel Enable 7 1 read-write 0 DMA channel is disabled. This mode is primarily used during configuration of the DMAMux. The DMA has separate channel enables/disables, which should be used to disable or reconfigure a DMA channel. #0 1 DMA channel is enabled #1 SOURCE DMA Channel Source (Slot) 0 6 read-write 0 Disable_Signal #0 2 UART0_Rx_Signal #10 4 UART1_Rx_Signal #100 16 SPI1_Signal #10000 32 FTM3_Channel0_Signal #100000 33 FTM3_Channel1_Signal #100001 34 FTM3_Channel2_Signal #100010 35 FTM3_Channel3_Signal #100011 18 I2C0_Signal #10010 36 FTM3_Channel4_Signal #100100 37 FTM3_Channel5_Signal #100101 19 I2C1_Signal #10011 38 FTM3_Channel6_Signal #100110 39 FTM3_Channel7_Signal #100111 5 UART1_Tx_Signal #101 20 FTM0_Channel0_Signal #10100 40 ADC0_Signal #101000 41 ADC1_Signal #101001 21 FTM0_Channel1_Signal #10101 42 CMP0_Signal #101010 43 CMP1_Signal #101011 22 FTM0_Channel2_Signal #10110 45 DAC0_Signal #101101 23 FTM0_Channel3_Signal #10111 46 DAC1_Signal #101110 3 UART0_Tx_Signal #11 6 UART2_Rx_Signal #110 12 I2S0_Rx_Signal #1100 24 FTM0_Channel4_Signal #11000 48 PDB_Signal #110000 49 PortA_Signal #110001 25 FTM0_Channel5_Signal #11001 50 PortB_Signal #110010 51 PortC_Signal #110011 13 I2S0_Tx_Signal #1101 26 FTM0_Channel6_Signal #11010 52 PortD_Signal #110100 53 PortE_Signal #110101 27 FTM0_Channel7_Signal #11011 7 UART2_Tx_Signal #111 14 SPI0_Rx_Signal #1110 28 FTM1_Channel0_Signal #11100 29 FTM1_Channel1_Signal #11101 58 LPUART0_Rx_Signal #111010 59 LPUART0_Tx_Signal #111011 15 SPI0_Tx_Signal #1111 30 FTM2_Channel0_Signal #11110 60 AlwaysOn60_Signal #111100 61 AlwaysOn61_Signal #111101 31 FTM2_Channel1_Signal #11111 62 AlwaysOn62_Signal #111110 63 AlwaysOn63_Signal #111111 TRIG DMA Channel Trigger Enable 6 1 read-write 0 Triggering is disabled. If triggering is disabled and ENBL is set, the DMA Channel will simply route the specified source to the DMA channel. (Normal mode) #0 1 Triggering is enabled. If triggering is enabled and ENBL is set, the DMAMUX is in Periodic Trigger mode. #1 CHCFG11 Channel Configuration register 0x42 8 read-write n 0x0 0x0 ENBL DMA Channel Enable 7 1 read-write 0 DMA channel is disabled. This mode is primarily used during configuration of the DMAMux. The DMA has separate channel enables/disables, which should be used to disable or reconfigure a DMA channel. #0 1 DMA channel is enabled #1 SOURCE DMA Channel Source (Slot) 0 6 read-write 0 Disable_Signal #0 2 UART0_Rx_Signal #10 4 UART1_Rx_Signal #100 16 SPI1_Signal #10000 32 FTM3_Channel0_Signal #100000 33 FTM3_Channel1_Signal #100001 34 FTM3_Channel2_Signal #100010 35 FTM3_Channel3_Signal #100011 18 I2C0_Signal #10010 36 FTM3_Channel4_Signal #100100 37 FTM3_Channel5_Signal #100101 19 I2C1_Signal #10011 38 FTM3_Channel6_Signal #100110 39 FTM3_Channel7_Signal #100111 5 UART1_Tx_Signal #101 20 FTM0_Channel0_Signal #10100 40 ADC0_Signal #101000 41 ADC1_Signal #101001 21 FTM0_Channel1_Signal #10101 42 CMP0_Signal #101010 43 CMP1_Signal #101011 22 FTM0_Channel2_Signal #10110 45 DAC0_Signal #101101 23 FTM0_Channel3_Signal #10111 46 DAC1_Signal #101110 3 UART0_Tx_Signal #11 6 UART2_Rx_Signal #110 12 I2S0_Rx_Signal #1100 24 FTM0_Channel4_Signal #11000 48 PDB_Signal #110000 49 PortA_Signal #110001 25 FTM0_Channel5_Signal #11001 50 PortB_Signal #110010 51 PortC_Signal #110011 13 I2S0_Tx_Signal #1101 26 FTM0_Channel6_Signal #11010 52 PortD_Signal #110100 53 PortE_Signal #110101 27 FTM0_Channel7_Signal #11011 7 UART2_Tx_Signal #111 14 SPI0_Rx_Signal #1110 28 FTM1_Channel0_Signal #11100 29 FTM1_Channel1_Signal #11101 58 LPUART0_Rx_Signal #111010 59 LPUART0_Tx_Signal #111011 15 SPI0_Tx_Signal #1111 30 FTM2_Channel0_Signal #11110 60 AlwaysOn60_Signal #111100 61 AlwaysOn61_Signal #111101 31 FTM2_Channel1_Signal #11111 62 AlwaysOn62_Signal #111110 63 AlwaysOn63_Signal #111111 TRIG DMA Channel Trigger Enable 6 1 read-write 0 Triggering is disabled. If triggering is disabled and ENBL is set, the DMA Channel will simply route the specified source to the DMA channel. (Normal mode) #0 1 Triggering is enabled. If triggering is enabled and ENBL is set, the DMAMUX is in Periodic Trigger mode. #1 CHCFG12 Channel Configuration register 0x4E 8 read-write n 0x0 0x0 ENBL DMA Channel Enable 7 1 read-write 0 DMA channel is disabled. This mode is primarily used during configuration of the DMAMux. The DMA has separate channel enables/disables, which should be used to disable or reconfigure a DMA channel. #0 1 DMA channel is enabled #1 SOURCE DMA Channel Source (Slot) 0 6 read-write 0 Disable_Signal #0 2 UART0_Rx_Signal #10 4 UART1_Rx_Signal #100 16 SPI1_Signal #10000 32 FTM3_Channel0_Signal #100000 33 FTM3_Channel1_Signal #100001 34 FTM3_Channel2_Signal #100010 35 FTM3_Channel3_Signal #100011 18 I2C0_Signal #10010 36 FTM3_Channel4_Signal #100100 37 FTM3_Channel5_Signal #100101 19 I2C1_Signal #10011 38 FTM3_Channel6_Signal #100110 39 FTM3_Channel7_Signal #100111 5 UART1_Tx_Signal #101 20 FTM0_Channel0_Signal #10100 40 ADC0_Signal #101000 41 ADC1_Signal #101001 21 FTM0_Channel1_Signal #10101 42 CMP0_Signal #101010 43 CMP1_Signal #101011 22 FTM0_Channel2_Signal #10110 45 DAC0_Signal #101101 23 FTM0_Channel3_Signal #10111 46 DAC1_Signal #101110 3 UART0_Tx_Signal #11 6 UART2_Rx_Signal #110 12 I2S0_Rx_Signal #1100 24 FTM0_Channel4_Signal #11000 48 PDB_Signal #110000 49 PortA_Signal #110001 25 FTM0_Channel5_Signal #11001 50 PortB_Signal #110010 51 PortC_Signal #110011 13 I2S0_Tx_Signal #1101 26 FTM0_Channel6_Signal #11010 52 PortD_Signal #110100 53 PortE_Signal #110101 27 FTM0_Channel7_Signal #11011 7 UART2_Tx_Signal #111 14 SPI0_Rx_Signal #1110 28 FTM1_Channel0_Signal #11100 29 FTM1_Channel1_Signal #11101 58 LPUART0_Rx_Signal #111010 59 LPUART0_Tx_Signal #111011 15 SPI0_Tx_Signal #1111 30 FTM2_Channel0_Signal #11110 60 AlwaysOn60_Signal #111100 61 AlwaysOn61_Signal #111101 31 FTM2_Channel1_Signal #11111 62 AlwaysOn62_Signal #111110 63 AlwaysOn63_Signal #111111 TRIG DMA Channel Trigger Enable 6 1 read-write 0 Triggering is disabled. If triggering is disabled and ENBL is set, the DMA Channel will simply route the specified source to the DMA channel. (Normal mode) #0 1 Triggering is enabled. If triggering is enabled and ENBL is set, the DMAMUX is in Periodic Trigger mode. #1 CHCFG13 Channel Configuration register 0x5B 8 read-write n 0x0 0x0 ENBL DMA Channel Enable 7 1 read-write 0 DMA channel is disabled. This mode is primarily used during configuration of the DMAMux. The DMA has separate channel enables/disables, which should be used to disable or reconfigure a DMA channel. #0 1 DMA channel is enabled #1 SOURCE DMA Channel Source (Slot) 0 6 read-write 0 Disable_Signal #0 2 UART0_Rx_Signal #10 4 UART1_Rx_Signal #100 16 SPI1_Signal #10000 32 FTM3_Channel0_Signal #100000 33 FTM3_Channel1_Signal #100001 34 FTM3_Channel2_Signal #100010 35 FTM3_Channel3_Signal #100011 18 I2C0_Signal #10010 36 FTM3_Channel4_Signal #100100 37 FTM3_Channel5_Signal #100101 19 I2C1_Signal #10011 38 FTM3_Channel6_Signal #100110 39 FTM3_Channel7_Signal #100111 5 UART1_Tx_Signal #101 20 FTM0_Channel0_Signal #10100 40 ADC0_Signal #101000 41 ADC1_Signal #101001 21 FTM0_Channel1_Signal #10101 42 CMP0_Signal #101010 43 CMP1_Signal #101011 22 FTM0_Channel2_Signal #10110 45 DAC0_Signal #101101 23 FTM0_Channel3_Signal #10111 46 DAC1_Signal #101110 3 UART0_Tx_Signal #11 6 UART2_Rx_Signal #110 12 I2S0_Rx_Signal #1100 24 FTM0_Channel4_Signal #11000 48 PDB_Signal #110000 49 PortA_Signal #110001 25 FTM0_Channel5_Signal #11001 50 PortB_Signal #110010 51 PortC_Signal #110011 13 I2S0_Tx_Signal #1101 26 FTM0_Channel6_Signal #11010 52 PortD_Signal #110100 53 PortE_Signal #110101 27 FTM0_Channel7_Signal #11011 7 UART2_Tx_Signal #111 14 SPI0_Rx_Signal #1110 28 FTM1_Channel0_Signal #11100 29 FTM1_Channel1_Signal #11101 58 LPUART0_Rx_Signal #111010 59 LPUART0_Tx_Signal #111011 15 SPI0_Tx_Signal #1111 30 FTM2_Channel0_Signal #11110 60 AlwaysOn60_Signal #111100 61 AlwaysOn61_Signal #111101 31 FTM2_Channel1_Signal #11111 62 AlwaysOn62_Signal #111110 63 AlwaysOn63_Signal #111111 TRIG DMA Channel Trigger Enable 6 1 read-write 0 Triggering is disabled. If triggering is disabled and ENBL is set, the DMA Channel will simply route the specified source to the DMA channel. (Normal mode) #0 1 Triggering is enabled. If triggering is enabled and ENBL is set, the DMAMUX is in Periodic Trigger mode. #1 CHCFG14 Channel Configuration register 0x69 8 read-write n 0x0 0x0 ENBL DMA Channel Enable 7 1 read-write 0 DMA channel is disabled. This mode is primarily used during configuration of the DMAMux. The DMA has separate channel enables/disables, which should be used to disable or reconfigure a DMA channel. #0 1 DMA channel is enabled #1 SOURCE DMA Channel Source (Slot) 0 6 read-write 0 Disable_Signal #0 2 UART0_Rx_Signal #10 4 UART1_Rx_Signal #100 16 SPI1_Signal #10000 32 FTM3_Channel0_Signal #100000 33 FTM3_Channel1_Signal #100001 34 FTM3_Channel2_Signal #100010 35 FTM3_Channel3_Signal #100011 18 I2C0_Signal #10010 36 FTM3_Channel4_Signal #100100 37 FTM3_Channel5_Signal #100101 19 I2C1_Signal #10011 38 FTM3_Channel6_Signal #100110 39 FTM3_Channel7_Signal #100111 5 UART1_Tx_Signal #101 20 FTM0_Channel0_Signal #10100 40 ADC0_Signal #101000 41 ADC1_Signal #101001 21 FTM0_Channel1_Signal #10101 42 CMP0_Signal #101010 43 CMP1_Signal #101011 22 FTM0_Channel2_Signal #10110 45 DAC0_Signal #101101 23 FTM0_Channel3_Signal #10111 46 DAC1_Signal #101110 3 UART0_Tx_Signal #11 6 UART2_Rx_Signal #110 12 I2S0_Rx_Signal #1100 24 FTM0_Channel4_Signal #11000 48 PDB_Signal #110000 49 PortA_Signal #110001 25 FTM0_Channel5_Signal #11001 50 PortB_Signal #110010 51 PortC_Signal #110011 13 I2S0_Tx_Signal #1101 26 FTM0_Channel6_Signal #11010 52 PortD_Signal #110100 53 PortE_Signal #110101 27 FTM0_Channel7_Signal #11011 7 UART2_Tx_Signal #111 14 SPI0_Rx_Signal #1110 28 FTM1_Channel0_Signal #11100 29 FTM1_Channel1_Signal #11101 58 LPUART0_Rx_Signal #111010 59 LPUART0_Tx_Signal #111011 15 SPI0_Tx_Signal #1111 30 FTM2_Channel0_Signal #11110 60 AlwaysOn60_Signal #111100 61 AlwaysOn61_Signal #111101 31 FTM2_Channel1_Signal #11111 62 AlwaysOn62_Signal #111110 63 AlwaysOn63_Signal #111111 TRIG DMA Channel Trigger Enable 6 1 read-write 0 Triggering is disabled. If triggering is disabled and ENBL is set, the DMA Channel will simply route the specified source to the DMA channel. (Normal mode) #0 1 Triggering is enabled. If triggering is enabled and ENBL is set, the DMAMUX is in Periodic Trigger mode. #1 CHCFG15 Channel Configuration register 0x78 8 read-write n 0x0 0x0 ENBL DMA Channel Enable 7 1 read-write 0 DMA channel is disabled. This mode is primarily used during configuration of the DMAMux. The DMA has separate channel enables/disables, which should be used to disable or reconfigure a DMA channel. #0 1 DMA channel is enabled #1 SOURCE DMA Channel Source (Slot) 0 6 read-write 0 Disable_Signal #0 2 UART0_Rx_Signal #10 4 UART1_Rx_Signal #100 16 SPI1_Signal #10000 32 FTM3_Channel0_Signal #100000 33 FTM3_Channel1_Signal #100001 34 FTM3_Channel2_Signal #100010 35 FTM3_Channel3_Signal #100011 18 I2C0_Signal #10010 36 FTM3_Channel4_Signal #100100 37 FTM3_Channel5_Signal #100101 19 I2C1_Signal #10011 38 FTM3_Channel6_Signal #100110 39 FTM3_Channel7_Signal #100111 5 UART1_Tx_Signal #101 20 FTM0_Channel0_Signal #10100 40 ADC0_Signal #101000 41 ADC1_Signal #101001 21 FTM0_Channel1_Signal #10101 42 CMP0_Signal #101010 43 CMP1_Signal #101011 22 FTM0_Channel2_Signal #10110 45 DAC0_Signal #101101 23 FTM0_Channel3_Signal #10111 46 DAC1_Signal #101110 3 UART0_Tx_Signal #11 6 UART2_Rx_Signal #110 12 I2S0_Rx_Signal #1100 24 FTM0_Channel4_Signal #11000 48 PDB_Signal #110000 49 PortA_Signal #110001 25 FTM0_Channel5_Signal #11001 50 PortB_Signal #110010 51 PortC_Signal #110011 13 I2S0_Tx_Signal #1101 26 FTM0_Channel6_Signal #11010 52 PortD_Signal #110100 53 PortE_Signal #110101 27 FTM0_Channel7_Signal #11011 7 UART2_Tx_Signal #111 14 SPI0_Rx_Signal #1110 28 FTM1_Channel0_Signal #11100 29 FTM1_Channel1_Signal #11101 58 LPUART0_Rx_Signal #111010 59 LPUART0_Tx_Signal #111011 15 SPI0_Tx_Signal #1111 30 FTM2_Channel0_Signal #11110 60 AlwaysOn60_Signal #111100 61 AlwaysOn61_Signal #111101 31 FTM2_Channel1_Signal #11111 62 AlwaysOn62_Signal #111110 63 AlwaysOn63_Signal #111111 TRIG DMA Channel Trigger Enable 6 1 read-write 0 Triggering is disabled. If triggering is disabled and ENBL is set, the DMA Channel will simply route the specified source to the DMA channel. (Normal mode) #0 1 Triggering is enabled. If triggering is enabled and ENBL is set, the DMAMUX is in Periodic Trigger mode. #1 CHCFG2 Channel Configuration register 0x3 8 read-write n 0x0 0x0 ENBL DMA Channel Enable 7 1 read-write 0 DMA channel is disabled. This mode is primarily used during configuration of the DMAMux. The DMA has separate channel enables/disables, which should be used to disable or reconfigure a DMA channel. #0 1 DMA channel is enabled #1 SOURCE DMA Channel Source (Slot) 0 6 read-write 0 Disable_Signal #0 2 UART0_Rx_Signal #10 4 UART1_Rx_Signal #100 16 SPI1_Signal #10000 32 FTM3_Channel0_Signal #100000 33 FTM3_Channel1_Signal #100001 34 FTM3_Channel2_Signal #100010 35 FTM3_Channel3_Signal #100011 18 I2C0_Signal #10010 36 FTM3_Channel4_Signal #100100 37 FTM3_Channel5_Signal #100101 19 I2C1_Signal #10011 38 FTM3_Channel6_Signal #100110 39 FTM3_Channel7_Signal #100111 5 UART1_Tx_Signal #101 20 FTM0_Channel0_Signal #10100 40 ADC0_Signal #101000 41 ADC1_Signal #101001 21 FTM0_Channel1_Signal #10101 42 CMP0_Signal #101010 43 CMP1_Signal #101011 22 FTM0_Channel2_Signal #10110 45 DAC0_Signal #101101 23 FTM0_Channel3_Signal #10111 46 DAC1_Signal #101110 3 UART0_Tx_Signal #11 6 UART2_Rx_Signal #110 12 I2S0_Rx_Signal #1100 24 FTM0_Channel4_Signal #11000 48 PDB_Signal #110000 49 PortA_Signal #110001 25 FTM0_Channel5_Signal #11001 50 PortB_Signal #110010 51 PortC_Signal #110011 13 I2S0_Tx_Signal #1101 26 FTM0_Channel6_Signal #11010 52 PortD_Signal #110100 53 PortE_Signal #110101 27 FTM0_Channel7_Signal #11011 7 UART2_Tx_Signal #111 14 SPI0_Rx_Signal #1110 28 FTM1_Channel0_Signal #11100 29 FTM1_Channel1_Signal #11101 58 LPUART0_Rx_Signal #111010 59 LPUART0_Tx_Signal #111011 15 SPI0_Tx_Signal #1111 30 FTM2_Channel0_Signal #11110 60 AlwaysOn60_Signal #111100 61 AlwaysOn61_Signal #111101 31 FTM2_Channel1_Signal #11111 62 AlwaysOn62_Signal #111110 63 AlwaysOn63_Signal #111111 TRIG DMA Channel Trigger Enable 6 1 read-write 0 Triggering is disabled. If triggering is disabled and ENBL is set, the DMA Channel will simply route the specified source to the DMA channel. (Normal mode) #0 1 Triggering is enabled. If triggering is enabled and ENBL is set, the DMAMUX is in Periodic Trigger mode. #1 CHCFG3 Channel Configuration register 0x6 8 read-write n 0x0 0x0 ENBL DMA Channel Enable 7 1 read-write 0 DMA channel is disabled. This mode is primarily used during configuration of the DMAMux. The DMA has separate channel enables/disables, which should be used to disable or reconfigure a DMA channel. #0 1 DMA channel is enabled #1 SOURCE DMA Channel Source (Slot) 0 6 read-write 0 Disable_Signal #0 2 UART0_Rx_Signal #10 4 UART1_Rx_Signal #100 16 SPI1_Signal #10000 32 FTM3_Channel0_Signal #100000 33 FTM3_Channel1_Signal #100001 34 FTM3_Channel2_Signal #100010 35 FTM3_Channel3_Signal #100011 18 I2C0_Signal #10010 36 FTM3_Channel4_Signal #100100 37 FTM3_Channel5_Signal #100101 19 I2C1_Signal #10011 38 FTM3_Channel6_Signal #100110 39 FTM3_Channel7_Signal #100111 5 UART1_Tx_Signal #101 20 FTM0_Channel0_Signal #10100 40 ADC0_Signal #101000 41 ADC1_Signal #101001 21 FTM0_Channel1_Signal #10101 42 CMP0_Signal #101010 43 CMP1_Signal #101011 22 FTM0_Channel2_Signal #10110 45 DAC0_Signal #101101 23 FTM0_Channel3_Signal #10111 46 DAC1_Signal #101110 3 UART0_Tx_Signal #11 6 UART2_Rx_Signal #110 12 I2S0_Rx_Signal #1100 24 FTM0_Channel4_Signal #11000 48 PDB_Signal #110000 49 PortA_Signal #110001 25 FTM0_Channel5_Signal #11001 50 PortB_Signal #110010 51 PortC_Signal #110011 13 I2S0_Tx_Signal #1101 26 FTM0_Channel6_Signal #11010 52 PortD_Signal #110100 53 PortE_Signal #110101 27 FTM0_Channel7_Signal #11011 7 UART2_Tx_Signal #111 14 SPI0_Rx_Signal #1110 28 FTM1_Channel0_Signal #11100 29 FTM1_Channel1_Signal #11101 58 LPUART0_Rx_Signal #111010 59 LPUART0_Tx_Signal #111011 15 SPI0_Tx_Signal #1111 30 FTM2_Channel0_Signal #11110 60 AlwaysOn60_Signal #111100 61 AlwaysOn61_Signal #111101 31 FTM2_Channel1_Signal #11111 62 AlwaysOn62_Signal #111110 63 AlwaysOn63_Signal #111111 TRIG DMA Channel Trigger Enable 6 1 read-write 0 Triggering is disabled. If triggering is disabled and ENBL is set, the DMA Channel will simply route the specified source to the DMA channel. (Normal mode) #0 1 Triggering is enabled. If triggering is enabled and ENBL is set, the DMAMUX is in Periodic Trigger mode. #1 CHCFG4 Channel Configuration register 0xA 8 read-write n 0x0 0x0 ENBL DMA Channel Enable 7 1 read-write 0 DMA channel is disabled. This mode is primarily used during configuration of the DMAMux. The DMA has separate channel enables/disables, which should be used to disable or reconfigure a DMA channel. #0 1 DMA channel is enabled #1 SOURCE DMA Channel Source (Slot) 0 6 read-write 0 Disable_Signal #0 2 UART0_Rx_Signal #10 4 UART1_Rx_Signal #100 16 SPI1_Signal #10000 32 FTM3_Channel0_Signal #100000 33 FTM3_Channel1_Signal #100001 34 FTM3_Channel2_Signal #100010 35 FTM3_Channel3_Signal #100011 18 I2C0_Signal #10010 36 FTM3_Channel4_Signal #100100 37 FTM3_Channel5_Signal #100101 19 I2C1_Signal #10011 38 FTM3_Channel6_Signal #100110 39 FTM3_Channel7_Signal #100111 5 UART1_Tx_Signal #101 20 FTM0_Channel0_Signal #10100 40 ADC0_Signal #101000 41 ADC1_Signal #101001 21 FTM0_Channel1_Signal #10101 42 CMP0_Signal #101010 43 CMP1_Signal #101011 22 FTM0_Channel2_Signal #10110 45 DAC0_Signal #101101 23 FTM0_Channel3_Signal #10111 46 DAC1_Signal #101110 3 UART0_Tx_Signal #11 6 UART2_Rx_Signal #110 12 I2S0_Rx_Signal #1100 24 FTM0_Channel4_Signal #11000 48 PDB_Signal #110000 49 PortA_Signal #110001 25 FTM0_Channel5_Signal #11001 50 PortB_Signal #110010 51 PortC_Signal #110011 13 I2S0_Tx_Signal #1101 26 FTM0_Channel6_Signal #11010 52 PortD_Signal #110100 53 PortE_Signal #110101 27 FTM0_Channel7_Signal #11011 7 UART2_Tx_Signal #111 14 SPI0_Rx_Signal #1110 28 FTM1_Channel0_Signal #11100 29 FTM1_Channel1_Signal #11101 58 LPUART0_Rx_Signal #111010 59 LPUART0_Tx_Signal #111011 15 SPI0_Tx_Signal #1111 30 FTM2_Channel0_Signal #11110 60 AlwaysOn60_Signal #111100 61 AlwaysOn61_Signal #111101 31 FTM2_Channel1_Signal #11111 62 AlwaysOn62_Signal #111110 63 AlwaysOn63_Signal #111111 TRIG DMA Channel Trigger Enable 6 1 read-write 0 Triggering is disabled. If triggering is disabled and ENBL is set, the DMA Channel will simply route the specified source to the DMA channel. (Normal mode) #0 1 Triggering is enabled. If triggering is enabled and ENBL is set, the DMAMUX is in Periodic Trigger mode. #1 CHCFG5 Channel Configuration register 0xF 8 read-write n 0x0 0x0 ENBL DMA Channel Enable 7 1 read-write 0 DMA channel is disabled. This mode is primarily used during configuration of the DMAMux. The DMA has separate channel enables/disables, which should be used to disable or reconfigure a DMA channel. #0 1 DMA channel is enabled #1 SOURCE DMA Channel Source (Slot) 0 6 read-write 0 Disable_Signal #0 2 UART0_Rx_Signal #10 4 UART1_Rx_Signal #100 16 SPI1_Signal #10000 32 FTM3_Channel0_Signal #100000 33 FTM3_Channel1_Signal #100001 34 FTM3_Channel2_Signal #100010 35 FTM3_Channel3_Signal #100011 18 I2C0_Signal #10010 36 FTM3_Channel4_Signal #100100 37 FTM3_Channel5_Signal #100101 19 I2C1_Signal #10011 38 FTM3_Channel6_Signal #100110 39 FTM3_Channel7_Signal #100111 5 UART1_Tx_Signal #101 20 FTM0_Channel0_Signal #10100 40 ADC0_Signal #101000 41 ADC1_Signal #101001 21 FTM0_Channel1_Signal #10101 42 CMP0_Signal #101010 43 CMP1_Signal #101011 22 FTM0_Channel2_Signal #10110 45 DAC0_Signal #101101 23 FTM0_Channel3_Signal #10111 46 DAC1_Signal #101110 3 UART0_Tx_Signal #11 6 UART2_Rx_Signal #110 12 I2S0_Rx_Signal #1100 24 FTM0_Channel4_Signal #11000 48 PDB_Signal #110000 49 PortA_Signal #110001 25 FTM0_Channel5_Signal #11001 50 PortB_Signal #110010 51 PortC_Signal #110011 13 I2S0_Tx_Signal #1101 26 FTM0_Channel6_Signal #11010 52 PortD_Signal #110100 53 PortE_Signal #110101 27 FTM0_Channel7_Signal #11011 7 UART2_Tx_Signal #111 14 SPI0_Rx_Signal #1110 28 FTM1_Channel0_Signal #11100 29 FTM1_Channel1_Signal #11101 58 LPUART0_Rx_Signal #111010 59 LPUART0_Tx_Signal #111011 15 SPI0_Tx_Signal #1111 30 FTM2_Channel0_Signal #11110 60 AlwaysOn60_Signal #111100 61 AlwaysOn61_Signal #111101 31 FTM2_Channel1_Signal #11111 62 AlwaysOn62_Signal #111110 63 AlwaysOn63_Signal #111111 TRIG DMA Channel Trigger Enable 6 1 read-write 0 Triggering is disabled. If triggering is disabled and ENBL is set, the DMA Channel will simply route the specified source to the DMA channel. (Normal mode) #0 1 Triggering is enabled. If triggering is enabled and ENBL is set, the DMAMUX is in Periodic Trigger mode. #1 CHCFG6 Channel Configuration register 0x15 8 read-write n 0x0 0x0 ENBL DMA Channel Enable 7 1 read-write 0 DMA channel is disabled. This mode is primarily used during configuration of the DMAMux. The DMA has separate channel enables/disables, which should be used to disable or reconfigure a DMA channel. #0 1 DMA channel is enabled #1 SOURCE DMA Channel Source (Slot) 0 6 read-write 0 Disable_Signal #0 2 UART0_Rx_Signal #10 4 UART1_Rx_Signal #100 16 SPI1_Signal #10000 32 FTM3_Channel0_Signal #100000 33 FTM3_Channel1_Signal #100001 34 FTM3_Channel2_Signal #100010 35 FTM3_Channel3_Signal #100011 18 I2C0_Signal #10010 36 FTM3_Channel4_Signal #100100 37 FTM3_Channel5_Signal #100101 19 I2C1_Signal #10011 38 FTM3_Channel6_Signal #100110 39 FTM3_Channel7_Signal #100111 5 UART1_Tx_Signal #101 20 FTM0_Channel0_Signal #10100 40 ADC0_Signal #101000 41 ADC1_Signal #101001 21 FTM0_Channel1_Signal #10101 42 CMP0_Signal #101010 43 CMP1_Signal #101011 22 FTM0_Channel2_Signal #10110 45 DAC0_Signal #101101 23 FTM0_Channel3_Signal #10111 46 DAC1_Signal #101110 3 UART0_Tx_Signal #11 6 UART2_Rx_Signal #110 12 I2S0_Rx_Signal #1100 24 FTM0_Channel4_Signal #11000 48 PDB_Signal #110000 49 PortA_Signal #110001 25 FTM0_Channel5_Signal #11001 50 PortB_Signal #110010 51 PortC_Signal #110011 13 I2S0_Tx_Signal #1101 26 FTM0_Channel6_Signal #11010 52 PortD_Signal #110100 53 PortE_Signal #110101 27 FTM0_Channel7_Signal #11011 7 UART2_Tx_Signal #111 14 SPI0_Rx_Signal #1110 28 FTM1_Channel0_Signal #11100 29 FTM1_Channel1_Signal #11101 58 LPUART0_Rx_Signal #111010 59 LPUART0_Tx_Signal #111011 15 SPI0_Tx_Signal #1111 30 FTM2_Channel0_Signal #11110 60 AlwaysOn60_Signal #111100 61 AlwaysOn61_Signal #111101 31 FTM2_Channel1_Signal #11111 62 AlwaysOn62_Signal #111110 63 AlwaysOn63_Signal #111111 TRIG DMA Channel Trigger Enable 6 1 read-write 0 Triggering is disabled. If triggering is disabled and ENBL is set, the DMA Channel will simply route the specified source to the DMA channel. (Normal mode) #0 1 Triggering is enabled. If triggering is enabled and ENBL is set, the DMAMUX is in Periodic Trigger mode. #1 CHCFG7 Channel Configuration register 0x1C 8 read-write n 0x0 0x0 ENBL DMA Channel Enable 7 1 read-write 0 DMA channel is disabled. This mode is primarily used during configuration of the DMAMux. The DMA has separate channel enables/disables, which should be used to disable or reconfigure a DMA channel. #0 1 DMA channel is enabled #1 SOURCE DMA Channel Source (Slot) 0 6 read-write 0 Disable_Signal #0 2 UART0_Rx_Signal #10 4 UART1_Rx_Signal #100 16 SPI1_Signal #10000 32 FTM3_Channel0_Signal #100000 33 FTM3_Channel1_Signal #100001 34 FTM3_Channel2_Signal #100010 35 FTM3_Channel3_Signal #100011 18 I2C0_Signal #10010 36 FTM3_Channel4_Signal #100100 37 FTM3_Channel5_Signal #100101 19 I2C1_Signal #10011 38 FTM3_Channel6_Signal #100110 39 FTM3_Channel7_Signal #100111 5 UART1_Tx_Signal #101 20 FTM0_Channel0_Signal #10100 40 ADC0_Signal #101000 41 ADC1_Signal #101001 21 FTM0_Channel1_Signal #10101 42 CMP0_Signal #101010 43 CMP1_Signal #101011 22 FTM0_Channel2_Signal #10110 45 DAC0_Signal #101101 23 FTM0_Channel3_Signal #10111 46 DAC1_Signal #101110 3 UART0_Tx_Signal #11 6 UART2_Rx_Signal #110 12 I2S0_Rx_Signal #1100 24 FTM0_Channel4_Signal #11000 48 PDB_Signal #110000 49 PortA_Signal #110001 25 FTM0_Channel5_Signal #11001 50 PortB_Signal #110010 51 PortC_Signal #110011 13 I2S0_Tx_Signal #1101 26 FTM0_Channel6_Signal #11010 52 PortD_Signal #110100 53 PortE_Signal #110101 27 FTM0_Channel7_Signal #11011 7 UART2_Tx_Signal #111 14 SPI0_Rx_Signal #1110 28 FTM1_Channel0_Signal #11100 29 FTM1_Channel1_Signal #11101 58 LPUART0_Rx_Signal #111010 59 LPUART0_Tx_Signal #111011 15 SPI0_Tx_Signal #1111 30 FTM2_Channel0_Signal #11110 60 AlwaysOn60_Signal #111100 61 AlwaysOn61_Signal #111101 31 FTM2_Channel1_Signal #11111 62 AlwaysOn62_Signal #111110 63 AlwaysOn63_Signal #111111 TRIG DMA Channel Trigger Enable 6 1 read-write 0 Triggering is disabled. If triggering is disabled and ENBL is set, the DMA Channel will simply route the specified source to the DMA channel. (Normal mode) #0 1 Triggering is enabled. If triggering is enabled and ENBL is set, the DMAMUX is in Periodic Trigger mode. #1 CHCFG8 Channel Configuration register 0x24 8 read-write n 0x0 0x0 ENBL DMA Channel Enable 7 1 read-write 0 DMA channel is disabled. This mode is primarily used during configuration of the DMAMux. The DMA has separate channel enables/disables, which should be used to disable or reconfigure a DMA channel. #0 1 DMA channel is enabled #1 SOURCE DMA Channel Source (Slot) 0 6 read-write 0 Disable_Signal #0 2 UART0_Rx_Signal #10 4 UART1_Rx_Signal #100 16 SPI1_Signal #10000 32 FTM3_Channel0_Signal #100000 33 FTM3_Channel1_Signal #100001 34 FTM3_Channel2_Signal #100010 35 FTM3_Channel3_Signal #100011 18 I2C0_Signal #10010 36 FTM3_Channel4_Signal #100100 37 FTM3_Channel5_Signal #100101 19 I2C1_Signal #10011 38 FTM3_Channel6_Signal #100110 39 FTM3_Channel7_Signal #100111 5 UART1_Tx_Signal #101 20 FTM0_Channel0_Signal #10100 40 ADC0_Signal #101000 41 ADC1_Signal #101001 21 FTM0_Channel1_Signal #10101 42 CMP0_Signal #101010 43 CMP1_Signal #101011 22 FTM0_Channel2_Signal #10110 45 DAC0_Signal #101101 23 FTM0_Channel3_Signal #10111 46 DAC1_Signal #101110 3 UART0_Tx_Signal #11 6 UART2_Rx_Signal #110 12 I2S0_Rx_Signal #1100 24 FTM0_Channel4_Signal #11000 48 PDB_Signal #110000 49 PortA_Signal #110001 25 FTM0_Channel5_Signal #11001 50 PortB_Signal #110010 51 PortC_Signal #110011 13 I2S0_Tx_Signal #1101 26 FTM0_Channel6_Signal #11010 52 PortD_Signal #110100 53 PortE_Signal #110101 27 FTM0_Channel7_Signal #11011 7 UART2_Tx_Signal #111 14 SPI0_Rx_Signal #1110 28 FTM1_Channel0_Signal #11100 29 FTM1_Channel1_Signal #11101 58 LPUART0_Rx_Signal #111010 59 LPUART0_Tx_Signal #111011 15 SPI0_Tx_Signal #1111 30 FTM2_Channel0_Signal #11110 60 AlwaysOn60_Signal #111100 61 AlwaysOn61_Signal #111101 31 FTM2_Channel1_Signal #11111 62 AlwaysOn62_Signal #111110 63 AlwaysOn63_Signal #111111 TRIG DMA Channel Trigger Enable 6 1 read-write 0 Triggering is disabled. If triggering is disabled and ENBL is set, the DMA Channel will simply route the specified source to the DMA channel. (Normal mode) #0 1 Triggering is enabled. If triggering is enabled and ENBL is set, the DMAMUX is in Periodic Trigger mode. #1 CHCFG9 Channel Configuration register 0x2D 8 read-write n 0x0 0x0 ENBL DMA Channel Enable 7 1 read-write 0 DMA channel is disabled. This mode is primarily used during configuration of the DMAMux. The DMA has separate channel enables/disables, which should be used to disable or reconfigure a DMA channel. #0 1 DMA channel is enabled #1 SOURCE DMA Channel Source (Slot) 0 6 read-write 0 Disable_Signal #0 2 UART0_Rx_Signal #10 4 UART1_Rx_Signal #100 16 SPI1_Signal #10000 32 FTM3_Channel0_Signal #100000 33 FTM3_Channel1_Signal #100001 34 FTM3_Channel2_Signal #100010 35 FTM3_Channel3_Signal #100011 18 I2C0_Signal #10010 36 FTM3_Channel4_Signal #100100 37 FTM3_Channel5_Signal #100101 19 I2C1_Signal #10011 38 FTM3_Channel6_Signal #100110 39 FTM3_Channel7_Signal #100111 5 UART1_Tx_Signal #101 20 FTM0_Channel0_Signal #10100 40 ADC0_Signal #101000 41 ADC1_Signal #101001 21 FTM0_Channel1_Signal #10101 42 CMP0_Signal #101010 43 CMP1_Signal #101011 22 FTM0_Channel2_Signal #10110 45 DAC0_Signal #101101 23 FTM0_Channel3_Signal #10111 46 DAC1_Signal #101110 3 UART0_Tx_Signal #11 6 UART2_Rx_Signal #110 12 I2S0_Rx_Signal #1100 24 FTM0_Channel4_Signal #11000 48 PDB_Signal #110000 49 PortA_Signal #110001 25 FTM0_Channel5_Signal #11001 50 PortB_Signal #110010 51 PortC_Signal #110011 13 I2S0_Tx_Signal #1101 26 FTM0_Channel6_Signal #11010 52 PortD_Signal #110100 53 PortE_Signal #110101 27 FTM0_Channel7_Signal #11011 7 UART2_Tx_Signal #111 14 SPI0_Rx_Signal #1110 28 FTM1_Channel0_Signal #11100 29 FTM1_Channel1_Signal #11101 58 LPUART0_Rx_Signal #111010 59 LPUART0_Tx_Signal #111011 15 SPI0_Tx_Signal #1111 30 FTM2_Channel0_Signal #11110 60 AlwaysOn60_Signal #111100 61 AlwaysOn61_Signal #111101 31 FTM2_Channel1_Signal #11111 62 AlwaysOn62_Signal #111110 63 AlwaysOn63_Signal #111111 TRIG DMA Channel Trigger Enable 6 1 read-write 0 Triggering is disabled. If triggering is disabled and ENBL is set, the DMA Channel will simply route the specified source to the DMA channel. (Normal mode) #0 1 Triggering is enabled. If triggering is enabled and ENBL is set, the DMAMUX is in Periodic Trigger mode. #1 EWM External Watchdog Monitor EWM 0x0 0x0 0x6 registers n WDOG_EWM 22 CLKPRESCALER Clock Prescaler Register 0x5 8 read-write n 0x0 0x0 CLK_DIV Selected low power source for running the EWM counter can be prescaled as below 0 8 read-write CMPH Compare High Register 0x3 8 read-write n 0x0 0x0 COMPAREH To prevent runaway code from changing this field, software should write to this field after a CPU reset even if the (default) maximum service time is required 0 8 read-write CMPL Compare Low Register 0x2 8 read-write n 0x0 0x0 COMPAREL To prevent runaway code from changing this field, software should write to this field after a CPU reset even if the (default) minimum service time is required 0 8 read-write CTRL Control Register 0x0 8 read-write n 0x0 0x0 ASSIN EWM_in's Assertion State Select. 1 1 read-write EWMEN EWM enable. 0 1 read-write INEN Input Enable. 2 1 read-write INTEN Interrupt Enable. 3 1 read-write SERV Service Register 0x1 8 write-only n 0x0 0x0 SERVICE The EWM service mechanism requires the CPU to write two values to the SERV register: a first data byte of 0xB4, followed by a second data byte of 0x2C 0 8 write-only FB FlexBus external bus interface FB 0x0 0x0 0x64 registers n CSAR0 Chip Select Address Register 0x0 32 read-write n 0x0 0x0 BA Base Address 16 16 read-write CSAR1 Chip Select Address Register 0xC 32 read-write n 0x0 0x0 BA Base Address 16 16 read-write CSAR2 Chip Select Address Register 0x24 32 read-write n 0x0 0x0 BA Base Address 16 16 read-write CSAR3 Chip Select Address Register 0x48 32 read-write n 0x0 0x0 BA Base Address 16 16 read-write CSAR4 Chip Select Address Register 0x78 32 read-write n 0x0 0x0 BA Base Address 16 16 read-write CSAR5 Chip Select Address Register 0xB4 32 read-write n 0x0 0x0 BA Base Address 16 16 read-write CSCR0 Chip Select Control Register 0x10 32 read-write n 0x0 0x0 AA Auto-Acknowledge Enable 8 1 read-write 0 Disabled. No internal transfer acknowledge is asserted and the cycle is terminated externally. #0 1 Enabled. Internal transfer acknowledge is asserted as specified by WS. #1 ASET Address Setup 20 2 read-write 00 Assert FB_CSn on the first rising clock edge after the address is asserted (default for all but FB_CS0 ). #00 01 Assert FB_CSn on the second rising clock edge after the address is asserted. #01 10 Assert FB_CSn on the third rising clock edge after the address is asserted. #10 11 Assert FB_CSn on the fourth rising clock edge after the address is asserted (default for FB_CS0 ). #11 BEM Byte-Enable Mode 5 1 read-write 0 FB_BE is asserted for data write only. #0 1 FB_BE is asserted for data read and write accesses. #1 BLS Byte-Lane Shift 9 1 read-write 0 Not shifted. Data is left-aligned on FB_AD. #0 1 Shifted. Data is right-aligned on FB_AD. #1 BSTR Burst-Read Enable 4 1 read-write 0 Disabled. Data exceeding the specified port size is broken into individual, port-sized, non-burst reads. For example, a 32-bit read from an 8-bit port is broken into four 8-bit reads. #0 1 Enabled. Enables data burst reads larger than the specified port size, including 32-bit reads from 8- and 16-bit ports, 16-bit reads from 8-bit ports, and line reads from 8-, 16-, and 32-bit ports. #1 BSTW Burst-Write Enable 3 1 read-write 0 Disabled. Data exceeding the specified port size is broken into individual, port-sized, non-burst writes. For example, a 32-bit write to an 8-bit port takes four byte writes. #0 1 Enabled. Enables burst write of data larger than the specified port size, including 32-bit writes to 8- and 16-bit ports, 16-bit writes to 8-bit ports, and line writes to 8-, 16-, and 32-bit ports. #1 EXTS Extended Transfer Start/Extended Address Latch Enable Controls how long FB_TS /FB_ALE is asserted. 22 1 read-write 0 Disabled. FB_TS /FB_ALE asserts for one bus clock cycle. #0 1 Enabled. FB_TS /FB_ALE remains asserted until the first positive clock edge after FB_CSn asserts. #1 PS Port Size 6 2 read-write 00 32-bit port size. Valid data is sampled and driven on FB_D[31:0]. #00 01 8-bit port size. Valid data is sampled and driven on FB_D[31:24] when BLS is 0b, or FB_D[7:0] when BLS is 1b. #01 RDAH Read Address Hold or Deselect 18 2 read-write 00 When AA is 0b, 1 cycle. When AA is 1b, 0 cycles. #00 01 When AA is 0b, 2 cycles. When AA is 1b, 1 cycle. #01 10 When AA is 0b, 3 cycles. When AA is 1b, 2 cycles. #10 11 When AA is 0b, 4 cycles. When AA is 1b, 3 cycles. #11 SWS Secondary Wait States 26 6 read-write SWSEN Secondary Wait State Enable 23 1 read-write 0 Disabled. A number of wait states (specified by WS) are inserted before an internal transfer acknowledge is generated for all transfers. #0 1 Enabled. A number of wait states (specified by SWS) are inserted before an internal transfer acknowledge is generated for burst transfer secondary terminations. #1 WRAH Write Address Hold or Deselect 16 2 read-write 00 1 cycle (default for all but FB_CS0 ) #00 01 2 cycles #01 10 3 cycles #10 11 4 cycles (default for FB_CS0 ) #11 WS Wait States 10 6 read-write CSCR1 Chip Select Control Register 0x24 32 read-write n 0x0 0x0 AA Auto-Acknowledge Enable 8 1 read-write 0 Disabled. No internal transfer acknowledge is asserted and the cycle is terminated externally. #0 1 Enabled. Internal transfer acknowledge is asserted as specified by WS. #1 ASET Address Setup 20 2 read-write 00 Assert FB_CSn on the first rising clock edge after the address is asserted (default for all but FB_CS0 ). #00 01 Assert FB_CSn on the second rising clock edge after the address is asserted. #01 10 Assert FB_CSn on the third rising clock edge after the address is asserted. #10 11 Assert FB_CSn on the fourth rising clock edge after the address is asserted (default for FB_CS0 ). #11 BEM Byte-Enable Mode 5 1 read-write 0 FB_BE is asserted for data write only. #0 1 FB_BE is asserted for data read and write accesses. #1 BLS Byte-Lane Shift 9 1 read-write 0 Not shifted. Data is left-aligned on FB_AD. #0 1 Shifted. Data is right-aligned on FB_AD. #1 BSTR Burst-Read Enable 4 1 read-write 0 Disabled. Data exceeding the specified port size is broken into individual, port-sized, non-burst reads. For example, a 32-bit read from an 8-bit port is broken into four 8-bit reads. #0 1 Enabled. Enables data burst reads larger than the specified port size, including 32-bit reads from 8- and 16-bit ports, 16-bit reads from 8-bit ports, and line reads from 8-, 16-, and 32-bit ports. #1 BSTW Burst-Write Enable 3 1 read-write 0 Disabled. Data exceeding the specified port size is broken into individual, port-sized, non-burst writes. For example, a 32-bit write to an 8-bit port takes four byte writes. #0 1 Enabled. Enables burst write of data larger than the specified port size, including 32-bit writes to 8- and 16-bit ports, 16-bit writes to 8-bit ports, and line writes to 8-, 16-, and 32-bit ports. #1 EXTS Extended Transfer Start/Extended Address Latch Enable Controls how long FB_TS /FB_ALE is asserted. 22 1 read-write 0 Disabled. FB_TS /FB_ALE asserts for one bus clock cycle. #0 1 Enabled. FB_TS /FB_ALE remains asserted until the first positive clock edge after FB_CSn asserts. #1 PS Port Size 6 2 read-write 00 32-bit port size. Valid data is sampled and driven on FB_D[31:0]. #00 01 8-bit port size. Valid data is sampled and driven on FB_D[31:24] when BLS is 0b, or FB_D[7:0] when BLS is 1b. #01 RDAH Read Address Hold or Deselect 18 2 read-write 00 When AA is 0b, 1 cycle. When AA is 1b, 0 cycles. #00 01 When AA is 0b, 2 cycles. When AA is 1b, 1 cycle. #01 10 When AA is 0b, 3 cycles. When AA is 1b, 2 cycles. #10 11 When AA is 0b, 4 cycles. When AA is 1b, 3 cycles. #11 SWS Secondary Wait States 26 6 read-write SWSEN Secondary Wait State Enable 23 1 read-write 0 Disabled. A number of wait states (specified by WS) are inserted before an internal transfer acknowledge is generated for all transfers. #0 1 Enabled. A number of wait states (specified by SWS) are inserted before an internal transfer acknowledge is generated for burst transfer secondary terminations. #1 WRAH Write Address Hold or Deselect 16 2 read-write 00 1 cycle (default for all but FB_CS0 ) #00 01 2 cycles #01 10 3 cycles #10 11 4 cycles (default for FB_CS0 ) #11 WS Wait States 10 6 read-write CSCR2 Chip Select Control Register 0x44 32 read-write n 0x0 0x0 AA Auto-Acknowledge Enable 8 1 read-write 0 Disabled. No internal transfer acknowledge is asserted and the cycle is terminated externally. #0 1 Enabled. Internal transfer acknowledge is asserted as specified by WS. #1 ASET Address Setup 20 2 read-write 00 Assert FB_CSn on the first rising clock edge after the address is asserted (default for all but FB_CS0 ). #00 01 Assert FB_CSn on the second rising clock edge after the address is asserted. #01 10 Assert FB_CSn on the third rising clock edge after the address is asserted. #10 11 Assert FB_CSn on the fourth rising clock edge after the address is asserted (default for FB_CS0 ). #11 BEM Byte-Enable Mode 5 1 read-write 0 FB_BE is asserted for data write only. #0 1 FB_BE is asserted for data read and write accesses. #1 BLS Byte-Lane Shift 9 1 read-write 0 Not shifted. Data is left-aligned on FB_AD. #0 1 Shifted. Data is right-aligned on FB_AD. #1 BSTR Burst-Read Enable 4 1 read-write 0 Disabled. Data exceeding the specified port size is broken into individual, port-sized, non-burst reads. For example, a 32-bit read from an 8-bit port is broken into four 8-bit reads. #0 1 Enabled. Enables data burst reads larger than the specified port size, including 32-bit reads from 8- and 16-bit ports, 16-bit reads from 8-bit ports, and line reads from 8-, 16-, and 32-bit ports. #1 BSTW Burst-Write Enable 3 1 read-write 0 Disabled. Data exceeding the specified port size is broken into individual, port-sized, non-burst writes. For example, a 32-bit write to an 8-bit port takes four byte writes. #0 1 Enabled. Enables burst write of data larger than the specified port size, including 32-bit writes to 8- and 16-bit ports, 16-bit writes to 8-bit ports, and line writes to 8-, 16-, and 32-bit ports. #1 EXTS Extended Transfer Start/Extended Address Latch Enable Controls how long FB_TS /FB_ALE is asserted. 22 1 read-write 0 Disabled. FB_TS /FB_ALE asserts for one bus clock cycle. #0 1 Enabled. FB_TS /FB_ALE remains asserted until the first positive clock edge after FB_CSn asserts. #1 PS Port Size 6 2 read-write 00 32-bit port size. Valid data is sampled and driven on FB_D[31:0]. #00 01 8-bit port size. Valid data is sampled and driven on FB_D[31:24] when BLS is 0b, or FB_D[7:0] when BLS is 1b. #01 RDAH Read Address Hold or Deselect 18 2 read-write 00 When AA is 0b, 1 cycle. When AA is 1b, 0 cycles. #00 01 When AA is 0b, 2 cycles. When AA is 1b, 1 cycle. #01 10 When AA is 0b, 3 cycles. When AA is 1b, 2 cycles. #10 11 When AA is 0b, 4 cycles. When AA is 1b, 3 cycles. #11 SWS Secondary Wait States 26 6 read-write SWSEN Secondary Wait State Enable 23 1 read-write 0 Disabled. A number of wait states (specified by WS) are inserted before an internal transfer acknowledge is generated for all transfers. #0 1 Enabled. A number of wait states (specified by SWS) are inserted before an internal transfer acknowledge is generated for burst transfer secondary terminations. #1 WRAH Write Address Hold or Deselect 16 2 read-write 00 1 cycle (default for all but FB_CS0 ) #00 01 2 cycles #01 10 3 cycles #10 11 4 cycles (default for FB_CS0 ) #11 WS Wait States 10 6 read-write CSCR3 Chip Select Control Register 0x70 32 read-write n 0x0 0x0 AA Auto-Acknowledge Enable 8 1 read-write 0 Disabled. No internal transfer acknowledge is asserted and the cycle is terminated externally. #0 1 Enabled. Internal transfer acknowledge is asserted as specified by WS. #1 ASET Address Setup 20 2 read-write 00 Assert FB_CSn on the first rising clock edge after the address is asserted (default for all but FB_CS0 ). #00 01 Assert FB_CSn on the second rising clock edge after the address is asserted. #01 10 Assert FB_CSn on the third rising clock edge after the address is asserted. #10 11 Assert FB_CSn on the fourth rising clock edge after the address is asserted (default for FB_CS0 ). #11 BEM Byte-Enable Mode 5 1 read-write 0 FB_BE is asserted for data write only. #0 1 FB_BE is asserted for data read and write accesses. #1 BLS Byte-Lane Shift 9 1 read-write 0 Not shifted. Data is left-aligned on FB_AD. #0 1 Shifted. Data is right-aligned on FB_AD. #1 BSTR Burst-Read Enable 4 1 read-write 0 Disabled. Data exceeding the specified port size is broken into individual, port-sized, non-burst reads. For example, a 32-bit read from an 8-bit port is broken into four 8-bit reads. #0 1 Enabled. Enables data burst reads larger than the specified port size, including 32-bit reads from 8- and 16-bit ports, 16-bit reads from 8-bit ports, and line reads from 8-, 16-, and 32-bit ports. #1 BSTW Burst-Write Enable 3 1 read-write 0 Disabled. Data exceeding the specified port size is broken into individual, port-sized, non-burst writes. For example, a 32-bit write to an 8-bit port takes four byte writes. #0 1 Enabled. Enables burst write of data larger than the specified port size, including 32-bit writes to 8- and 16-bit ports, 16-bit writes to 8-bit ports, and line writes to 8-, 16-, and 32-bit ports. #1 EXTS Extended Transfer Start/Extended Address Latch Enable Controls how long FB_TS /FB_ALE is asserted. 22 1 read-write 0 Disabled. FB_TS /FB_ALE asserts for one bus clock cycle. #0 1 Enabled. FB_TS /FB_ALE remains asserted until the first positive clock edge after FB_CSn asserts. #1 PS Port Size 6 2 read-write 00 32-bit port size. Valid data is sampled and driven on FB_D[31:0]. #00 01 8-bit port size. Valid data is sampled and driven on FB_D[31:24] when BLS is 0b, or FB_D[7:0] when BLS is 1b. #01 RDAH Read Address Hold or Deselect 18 2 read-write 00 When AA is 0b, 1 cycle. When AA is 1b, 0 cycles. #00 01 When AA is 0b, 2 cycles. When AA is 1b, 1 cycle. #01 10 When AA is 0b, 3 cycles. When AA is 1b, 2 cycles. #10 11 When AA is 0b, 4 cycles. When AA is 1b, 3 cycles. #11 SWS Secondary Wait States 26 6 read-write SWSEN Secondary Wait State Enable 23 1 read-write 0 Disabled. A number of wait states (specified by WS) are inserted before an internal transfer acknowledge is generated for all transfers. #0 1 Enabled. A number of wait states (specified by SWS) are inserted before an internal transfer acknowledge is generated for burst transfer secondary terminations. #1 WRAH Write Address Hold or Deselect 16 2 read-write 00 1 cycle (default for all but FB_CS0 ) #00 01 2 cycles #01 10 3 cycles #10 11 4 cycles (default for FB_CS0 ) #11 WS Wait States 10 6 read-write CSCR4 Chip Select Control Register 0xA8 32 read-write n 0x0 0x0 AA Auto-Acknowledge Enable 8 1 read-write 0 Disabled. No internal transfer acknowledge is asserted and the cycle is terminated externally. #0 1 Enabled. Internal transfer acknowledge is asserted as specified by WS. #1 ASET Address Setup 20 2 read-write 00 Assert FB_CSn on the first rising clock edge after the address is asserted (default for all but FB_CS0 ). #00 01 Assert FB_CSn on the second rising clock edge after the address is asserted. #01 10 Assert FB_CSn on the third rising clock edge after the address is asserted. #10 11 Assert FB_CSn on the fourth rising clock edge after the address is asserted (default for FB_CS0 ). #11 BEM Byte-Enable Mode 5 1 read-write 0 FB_BE is asserted for data write only. #0 1 FB_BE is asserted for data read and write accesses. #1 BLS Byte-Lane Shift 9 1 read-write 0 Not shifted. Data is left-aligned on FB_AD. #0 1 Shifted. Data is right-aligned on FB_AD. #1 BSTR Burst-Read Enable 4 1 read-write 0 Disabled. Data exceeding the specified port size is broken into individual, port-sized, non-burst reads. For example, a 32-bit read from an 8-bit port is broken into four 8-bit reads. #0 1 Enabled. Enables data burst reads larger than the specified port size, including 32-bit reads from 8- and 16-bit ports, 16-bit reads from 8-bit ports, and line reads from 8-, 16-, and 32-bit ports. #1 BSTW Burst-Write Enable 3 1 read-write 0 Disabled. Data exceeding the specified port size is broken into individual, port-sized, non-burst writes. For example, a 32-bit write to an 8-bit port takes four byte writes. #0 1 Enabled. Enables burst write of data larger than the specified port size, including 32-bit writes to 8- and 16-bit ports, 16-bit writes to 8-bit ports, and line writes to 8-, 16-, and 32-bit ports. #1 EXTS Extended Transfer Start/Extended Address Latch Enable Controls how long FB_TS /FB_ALE is asserted. 22 1 read-write 0 Disabled. FB_TS /FB_ALE asserts for one bus clock cycle. #0 1 Enabled. FB_TS /FB_ALE remains asserted until the first positive clock edge after FB_CSn asserts. #1 PS Port Size 6 2 read-write 00 32-bit port size. Valid data is sampled and driven on FB_D[31:0]. #00 01 8-bit port size. Valid data is sampled and driven on FB_D[31:24] when BLS is 0b, or FB_D[7:0] when BLS is 1b. #01 RDAH Read Address Hold or Deselect 18 2 read-write 00 When AA is 0b, 1 cycle. When AA is 1b, 0 cycles. #00 01 When AA is 0b, 2 cycles. When AA is 1b, 1 cycle. #01 10 When AA is 0b, 3 cycles. When AA is 1b, 2 cycles. #10 11 When AA is 0b, 4 cycles. When AA is 1b, 3 cycles. #11 SWS Secondary Wait States 26 6 read-write SWSEN Secondary Wait State Enable 23 1 read-write 0 Disabled. A number of wait states (specified by WS) are inserted before an internal transfer acknowledge is generated for all transfers. #0 1 Enabled. A number of wait states (specified by SWS) are inserted before an internal transfer acknowledge is generated for burst transfer secondary terminations. #1 WRAH Write Address Hold or Deselect 16 2 read-write 00 1 cycle (default for all but FB_CS0 ) #00 01 2 cycles #01 10 3 cycles #10 11 4 cycles (default for FB_CS0 ) #11 WS Wait States 10 6 read-write CSCR5 Chip Select Control Register 0xEC 32 read-write n 0x0 0x0 AA Auto-Acknowledge Enable 8 1 read-write 0 Disabled. No internal transfer acknowledge is asserted and the cycle is terminated externally. #0 1 Enabled. Internal transfer acknowledge is asserted as specified by WS. #1 ASET Address Setup 20 2 read-write 00 Assert FB_CSn on the first rising clock edge after the address is asserted (default for all but FB_CS0 ). #00 01 Assert FB_CSn on the second rising clock edge after the address is asserted. #01 10 Assert FB_CSn on the third rising clock edge after the address is asserted. #10 11 Assert FB_CSn on the fourth rising clock edge after the address is asserted (default for FB_CS0 ). #11 BEM Byte-Enable Mode 5 1 read-write 0 FB_BE is asserted for data write only. #0 1 FB_BE is asserted for data read and write accesses. #1 BLS Byte-Lane Shift 9 1 read-write 0 Not shifted. Data is left-aligned on FB_AD. #0 1 Shifted. Data is right-aligned on FB_AD. #1 BSTR Burst-Read Enable 4 1 read-write 0 Disabled. Data exceeding the specified port size is broken into individual, port-sized, non-burst reads. For example, a 32-bit read from an 8-bit port is broken into four 8-bit reads. #0 1 Enabled. Enables data burst reads larger than the specified port size, including 32-bit reads from 8- and 16-bit ports, 16-bit reads from 8-bit ports, and line reads from 8-, 16-, and 32-bit ports. #1 BSTW Burst-Write Enable 3 1 read-write 0 Disabled. Data exceeding the specified port size is broken into individual, port-sized, non-burst writes. For example, a 32-bit write to an 8-bit port takes four byte writes. #0 1 Enabled. Enables burst write of data larger than the specified port size, including 32-bit writes to 8- and 16-bit ports, 16-bit writes to 8-bit ports, and line writes to 8-, 16-, and 32-bit ports. #1 EXTS Extended Transfer Start/Extended Address Latch Enable Controls how long FB_TS /FB_ALE is asserted. 22 1 read-write 0 Disabled. FB_TS /FB_ALE asserts for one bus clock cycle. #0 1 Enabled. FB_TS /FB_ALE remains asserted until the first positive clock edge after FB_CSn asserts. #1 PS Port Size 6 2 read-write 00 32-bit port size. Valid data is sampled and driven on FB_D[31:0]. #00 01 8-bit port size. Valid data is sampled and driven on FB_D[31:24] when BLS is 0b, or FB_D[7:0] when BLS is 1b. #01 RDAH Read Address Hold or Deselect 18 2 read-write 00 When AA is 0b, 1 cycle. When AA is 1b, 0 cycles. #00 01 When AA is 0b, 2 cycles. When AA is 1b, 1 cycle. #01 10 When AA is 0b, 3 cycles. When AA is 1b, 2 cycles. #10 11 When AA is 0b, 4 cycles. When AA is 1b, 3 cycles. #11 SWS Secondary Wait States 26 6 read-write SWSEN Secondary Wait State Enable 23 1 read-write 0 Disabled. A number of wait states (specified by WS) are inserted before an internal transfer acknowledge is generated for all transfers. #0 1 Enabled. A number of wait states (specified by SWS) are inserted before an internal transfer acknowledge is generated for burst transfer secondary terminations. #1 WRAH Write Address Hold or Deselect 16 2 read-write 00 1 cycle (default for all but FB_CS0 ) #00 01 2 cycles #01 10 3 cycles #10 11 4 cycles (default for FB_CS0 ) #11 WS Wait States 10 6 read-write CSMR0 Chip Select Mask Register 0x8 32 read-write n 0x0 0x0 BAM Base Address Mask 16 16 read-write 0 The corresponding address bit in CSAR is used in the chip-select decode. #0 1 The corresponding address bit in CSAR is a don't care in the chip-select decode. #1 V Valid 0 1 read-write 0 Chip-select is invalid. #0 1 Chip-select is valid. #1 WP Write Protect 8 1 read-write 0 Write accesses are allowed. #0 1 Write accesses are not allowed. Attempting to write to the range of addresses for which the WP bit is set results in a bus error termination of the internal cycle and no external cycle. #1 CSMR1 Chip Select Mask Register 0x18 32 read-write n 0x0 0x0 BAM Base Address Mask 16 16 read-write 0 The corresponding address bit in CSAR is used in the chip-select decode. #0 1 The corresponding address bit in CSAR is a don't care in the chip-select decode. #1 V Valid 0 1 read-write 0 Chip-select is invalid. #0 1 Chip-select is valid. #1 WP Write Protect 8 1 read-write 0 Write accesses are allowed. #0 1 Write accesses are not allowed. Attempting to write to the range of addresses for which the WP bit is set results in a bus error termination of the internal cycle and no external cycle. #1 CSMR2 Chip Select Mask Register 0x34 32 read-write n 0x0 0x0 BAM Base Address Mask 16 16 read-write 0 The corresponding address bit in CSAR is used in the chip-select decode. #0 1 The corresponding address bit in CSAR is a don't care in the chip-select decode. #1 V Valid 0 1 read-write 0 Chip-select is invalid. #0 1 Chip-select is valid. #1 WP Write Protect 8 1 read-write 0 Write accesses are allowed. #0 1 Write accesses are not allowed. Attempting to write to the range of addresses for which the WP bit is set results in a bus error termination of the internal cycle and no external cycle. #1 CSMR3 Chip Select Mask Register 0x5C 32 read-write n 0x0 0x0 BAM Base Address Mask 16 16 read-write 0 The corresponding address bit in CSAR is used in the chip-select decode. #0 1 The corresponding address bit in CSAR is a don't care in the chip-select decode. #1 V Valid 0 1 read-write 0 Chip-select is invalid. #0 1 Chip-select is valid. #1 WP Write Protect 8 1 read-write 0 Write accesses are allowed. #0 1 Write accesses are not allowed. Attempting to write to the range of addresses for which the WP bit is set results in a bus error termination of the internal cycle and no external cycle. #1 CSMR4 Chip Select Mask Register 0x90 32 read-write n 0x0 0x0 BAM Base Address Mask 16 16 read-write 0 The corresponding address bit in CSAR is used in the chip-select decode. #0 1 The corresponding address bit in CSAR is a don't care in the chip-select decode. #1 V Valid 0 1 read-write 0 Chip-select is invalid. #0 1 Chip-select is valid. #1 WP Write Protect 8 1 read-write 0 Write accesses are allowed. #0 1 Write accesses are not allowed. Attempting to write to the range of addresses for which the WP bit is set results in a bus error termination of the internal cycle and no external cycle. #1 CSMR5 Chip Select Mask Register 0xD0 32 read-write n 0x0 0x0 BAM Base Address Mask 16 16 read-write 0 The corresponding address bit in CSAR is used in the chip-select decode. #0 1 The corresponding address bit in CSAR is a don't care in the chip-select decode. #1 V Valid 0 1 read-write 0 Chip-select is invalid. #0 1 Chip-select is valid. #1 WP Write Protect 8 1 read-write 0 Write accesses are allowed. #0 1 Write accesses are not allowed. Attempting to write to the range of addresses for which the WP bit is set results in a bus error termination of the internal cycle and no external cycle. #1 CSPMCR Chip Select port Multiplexing Control Register 0x60 32 read-write n 0x0 0x0 GROUP1 FlexBus Signal Group 1 Multiplex control 28 4 read-write 0000 FB_ALE #0000 0001 FB_CS1 #0001 0010 FB_TS #0010 GROUP2 FlexBus Signal Group 2 Multiplex control 24 4 read-write 0000 FB_CS4 #0000 0001 FB_TSIZ0 #0001 0010 FB_BE_31_24 #0010 GROUP3 FlexBus Signal Group 3 Multiplex control 20 4 read-write 0000 FB_CS5 #0000 0001 FB_TSIZ1 #0001 0010 FB_BE_23_16 #0010 GROUP4 FlexBus Signal Group 4 Multiplex control 16 4 read-write 0000 FB_TBST #0000 0001 FB_CS2 #0001 0010 FB_BE_15_8 #0010 GROUP5 FlexBus Signal Group 5 Multiplex control 12 4 read-write 0000 FB_TA #0000 0001 FB_CS3 . You must also write 1b to CSCR[AA]. #0001 0010 FB_BE_7_0 . You must also write 1b to CSCR[AA]. #0010 FMC Flash Memory Controller FMC 0x0 0x0 0x300 registers n DATAW0S0L Cache Data Storage (lower word) 0x408 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW0S0U Cache Data Storage (upper word) 0x400 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW0S1L Cache Data Storage (lower word) 0x614 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW0S1U Cache Data Storage (upper word) 0x608 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW0S2L Cache Data Storage (lower word) 0x828 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW0S2U Cache Data Storage (upper word) 0x818 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW0S3L Cache Data Storage (lower word) 0xA44 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW0S3U Cache Data Storage (upper word) 0xA30 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW0S4L Cache Data Storage (lower word) 0xC68 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW0S4U Cache Data Storage (upper word) 0xC50 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW0S5L Cache Data Storage (lower word) 0xE94 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW0S5U Cache Data Storage (upper word) 0xE78 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW0S6L Cache Data Storage (lower word) 0x10C8 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW0S6U Cache Data Storage (upper word) 0x10A8 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW0S7L Cache Data Storage (lower word) 0x1304 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW0S7U Cache Data Storage (upper word) 0x12E0 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW1S0L Cache Data Storage (lower word) 0x488 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW1S0U Cache Data Storage (upper word) 0x480 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW1S1L Cache Data Storage (lower word) 0x6D4 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW1S1U Cache Data Storage (upper word) 0x6C8 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW1S2L Cache Data Storage (lower word) 0x928 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW1S2U Cache Data Storage (upper word) 0x918 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW1S3L Cache Data Storage (lower word) 0xB84 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW1S3U Cache Data Storage (upper word) 0xB70 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW1S4L Cache Data Storage (lower word) 0xDE8 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW1S4U Cache Data Storage (upper word) 0xDD0 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW1S5L Cache Data Storage (lower word) 0x1054 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW1S5U Cache Data Storage (upper word) 0x1038 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW1S6L Cache Data Storage (lower word) 0x12C8 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW1S6U Cache Data Storage (upper word) 0x12A8 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW1S7L Cache Data Storage (lower word) 0x1544 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW1S7U Cache Data Storage (upper word) 0x1520 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW2S0L Cache Data Storage (lower word) 0x508 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW2S0U Cache Data Storage (upper word) 0x500 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW2S1L Cache Data Storage (lower word) 0x794 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW2S1U Cache Data Storage (upper word) 0x788 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW2S2L Cache Data Storage (lower word) 0xA28 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW2S2U Cache Data Storage (upper word) 0xA18 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW2S3L Cache Data Storage (lower word) 0xCC4 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW2S3U Cache Data Storage (upper word) 0xCB0 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW2S4L Cache Data Storage (lower word) 0xF68 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW2S4U Cache Data Storage (upper word) 0xF50 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW2S5L Cache Data Storage (lower word) 0x1214 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW2S5U Cache Data Storage (upper word) 0x11F8 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW2S6L Cache Data Storage (lower word) 0x14C8 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW2S6U Cache Data Storage (upper word) 0x14A8 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW2S7L Cache Data Storage (lower word) 0x1784 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW2S7U Cache Data Storage (upper word) 0x1760 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW3S0L Cache Data Storage (lower word) 0x588 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW3S0U Cache Data Storage (upper word) 0x580 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW3S1L Cache Data Storage (lower word) 0x854 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW3S1U Cache Data Storage (upper word) 0x848 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW3S2L Cache Data Storage (lower word) 0xB28 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW3S2U Cache Data Storage (upper word) 0xB18 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW3S3L Cache Data Storage (lower word) 0xE04 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW3S3U Cache Data Storage (upper word) 0xDF0 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW3S4L Cache Data Storage (lower word) 0x10E8 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW3S4U Cache Data Storage (upper word) 0x10D0 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW3S5L Cache Data Storage (lower word) 0x13D4 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW3S5U Cache Data Storage (upper word) 0x13B8 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW3S6L Cache Data Storage (lower word) 0x16C8 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW3S6U Cache Data Storage (upper word) 0x16A8 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write DATAW3S7L Cache Data Storage (lower word) 0x19C4 32 read-write n 0x0 0x0 data Bits [31:0] of data entry 0 32 read-write DATAW3S7U Cache Data Storage (upper word) 0x19A0 32 read-write n 0x0 0x0 data Bits [63:32] of data entry 0 32 read-write PFAPR Flash Access Protection Register 0x0 32 read-write n 0x0 0x0 M0AP Master 0 Access Protection 0 2 read-write 00 No access may be performed by this master #00 01 Only read accesses may be performed by this master #01 10 Only write accesses may be performed by this master #10 11 Both read and write accesses may be performed by this master #11 M0PFD Master 0 Prefetch Disable 16 1 read-write 0 Prefetching for this master is enabled. #0 1 Prefetching for this master is disabled. #1 M1AP Master 1 Access Protection 2 2 read-write 00 No access may be performed by this master #00 01 Only read accesses may be performed by this master #01 10 Only write accesses may be performed by this master #10 11 Both read and write accesses may be performed by this master #11 M1PFD Master 1 Prefetch Disable 17 1 read-write 0 Prefetching for this master is enabled. #0 1 Prefetching for this master is disabled. #1 M2AP Master 2 Access Protection 4 2 read-write 00 No access may be performed by this master #00 01 Only read accesses may be performed by this master #01 10 Only write accesses may be performed by this master #10 11 Both read and write accesses may be performed by this master #11 M2PFD Master 2 Prefetch Disable 18 1 read-write 0 Prefetching for this master is enabled. #0 1 Prefetching for this master is disabled. #1 M3AP Master 3 Access Protection 6 2 read-write 00 No access may be performed by this master #00 01 Only read accesses may be performed by this master #01 10 Only write accesses may be performed by this master #10 11 Both read and write accesses may be performed by this master #11 M3PFD Master 3 Prefetch Disable 19 1 read-write 0 Prefetching for this master is enabled. #0 1 Prefetching for this master is disabled. #1 M4AP Master 4 Access Protection 8 2 read-write 00 No access may be performed by this master #00 01 Only read accesses may be performed by this master #01 10 Only write accesses may be performed by this master #10 11 Both read and write accesses may be performed by this master #11 M4PFD Master 4 Prefetch Disable 20 1 read-write 0 Prefetching for this master is enabled. #0 1 Prefetching for this master is disabled. #1 M5AP Master 5 Access Protection 10 2 read-write 00 No access may be performed by this master #00 01 Only read accesses may be performed by this master #01 10 Only write accesses may be performed by this master #10 11 Both read and write accesses may be performed by this master #11 M5PFD Master 5 Prefetch Disable 21 1 read-write 0 Prefetching for this master is enabled. #0 1 Prefetching for this master is disabled. #1 M6AP Master 6 Access Protection 12 2 read-write 00 No access may be performed by this master #00 01 Only read accesses may be performed by this master #01 10 Only write accesses may be performed by this master #10 11 Both read and write accesses may be performed by this master #11 M6PFD Master 6 Prefetch Disable 22 1 read-write 0 Prefetching for this master is enabled. #0 1 Prefetching for this master is disabled. #1 M7AP Master 7 Access Protection 14 2 read-write 00 No access may be performed by this master. #00 01 Only read accesses may be performed by this master. #01 10 Only write accesses may be performed by this master. #10 11 Both read and write accesses may be performed by this master. #11 M7PFD Master 7 Prefetch Disable 23 1 read-write 0 Prefetching for this master is enabled. #0 1 Prefetching for this master is disabled. #1 PFB0CR Flash Bank 0 Control Register 0x4 32 read-write n 0x0 0x0 B0DCE Bank 0 Data Cache Enable 4 1 read-write 0 Do not cache data references. #0 1 Cache data references. #1 B0DPE Bank 0 Data Prefetch Enable 2 1 read-write 0 Do not prefetch in response to data references. #0 1 Enable prefetches in response to data references. #1 B0ICE Bank 0 Instruction Cache Enable 3 1 read-write 0 Do not cache instruction fetches. #0 1 Cache instruction fetches. #1 B0IPE Bank 0 Instruction Prefetch Enable 1 1 read-write 0 Do not prefetch in response to instruction fetches. #0 1 Enable prefetches in response to instruction fetches. #1 B0MW Bank 0 Memory Width 17 2 read-only 00 32 bits #00 01 64 bits #01 B0RWSC Bank 0 Read Wait State Control 28 4 read-only B0SEBE Bank 0 Single Entry Buffer Enable 0 1 read-write 0 Single entry buffer is disabled. #0 1 Single entry buffer is enabled. #1 CINV_WAY Cache Invalidate Way x 20 4 write-only 0 No cache way invalidation for the corresponding cache #0000 1 Invalidate cache way for the corresponding cache: clear the tag, data, and vld bits of ways selected #0001 CLCK_WAY Cache Lock Way x 24 4 read-write 0 Cache way is unlocked and may be displaced #0000 1 Cache way is locked and its contents are not displaced #0001 CRC Cache Replacement Control 5 3 read-write 000 LRU replacement algorithm per set across all four ways #000 010 Independent LRU with ways [0-1] for ifetches, [2-3] for data #010 011 Independent LRU with ways [0-2] for ifetches, [3] for data #011 S_B_INV Invalidate Prefetch Speculation Buffer 19 1 write-only 0 Speculation buffer and single entry buffer are not affected. #0 1 Invalidate (clear) speculation buffer and single entry buffer. #1 PFB1CR Flash Bank 1 Control Register 0x8 32 read-write n 0x0 0x0 B1DCE Bank 1 Data Cache Enable 4 1 read-write 0 Do not cache data references. #0 1 Cache data references. #1 B1DPE Bank 1 Data Prefetch Enable 2 1 read-write 0 Do not prefetch in response to data references. #0 1 Enable prefetches in response to data references. #1 B1ICE Bank 1 Instruction Cache Enable 3 1 read-write 0 Do not cache instruction fetches. #0 1 Cache instruction fetches. #1 B1IPE Bank 1 Instruction Prefetch Enable 1 1 read-write 0 Do not prefetch in response to instruction fetches. #0 1 Enable prefetches in response to instruction fetches. #1 B1MW Bank 1 Memory Width 17 2 read-only 00 32 bits #00 01 64 bits #01 B1RWSC Bank 1 Read Wait State Control 28 4 read-only B1SEBE Bank 1 Single Entry Buffer Enable 0 1 read-write 0 Single entry buffer is disabled. #0 1 Single entry buffer is enabled. #1 TAGVDW0S0 Cache Tag Storage 0x200 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW0S1 Cache Tag Storage 0x304 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW0S2 Cache Tag Storage 0x40C 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW0S3 Cache Tag Storage 0x518 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW0S4 Cache Tag Storage 0x628 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW0S5 Cache Tag Storage 0x73C 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW0S6 Cache Tag Storage 0x854 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW0S7 Cache Tag Storage 0x970 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW1S0 Cache Tag Storage 0x240 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW1S1 Cache Tag Storage 0x364 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW1S2 Cache Tag Storage 0x48C 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW1S3 Cache Tag Storage 0x5B8 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW1S4 Cache Tag Storage 0x6E8 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW1S5 Cache Tag Storage 0x81C 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW1S6 Cache Tag Storage 0x954 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW1S7 Cache Tag Storage 0xA90 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW2S0 Cache Tag Storage 0x280 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW2S1 Cache Tag Storage 0x3C4 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW2S2 Cache Tag Storage 0x50C 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW2S3 Cache Tag Storage 0x658 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW2S4 Cache Tag Storage 0x7A8 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW2S5 Cache Tag Storage 0x8FC 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW2S6 Cache Tag Storage 0xA54 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW2S7 Cache Tag Storage 0xBB0 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW3S0 Cache Tag Storage 0x2C0 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW3S1 Cache Tag Storage 0x424 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW3S2 Cache Tag Storage 0x58C 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW3S3 Cache Tag Storage 0x6F8 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW3S4 Cache Tag Storage 0x868 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW3S5 Cache Tag Storage 0x9DC 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW3S6 Cache Tag Storage 0xB54 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write TAGVDW3S7 Cache Tag Storage 0xCD0 32 read-write n 0x0 0x0 tag 14-bit tag for cache entry 5 14 read-write valid 1-bit valid for cache entry 0 1 read-write FTFA Flash Memory Interface FTFA 0x0 0x0 0x2C registers n FTF 18 Read_Collision 19 FACSN Flash Access Segment Number Register 0x2B 8 read-only n 0x0 0x0 NUMSG Number of Segments Indicator 0 8 read-only 100000 Program flash memory is divided into 32 segments (64 Kbytes, 128 Kbytes) #100000 1000000 Program flash memory is divided into 64 segments (256 Kbytes, 512 Kbytes) #1000000 101000 Program flash memory is divided into 40 segments (160 Kbytes) #101000 FACSS Flash Access Segment Size Register 0x28 8 read-only n 0x0 0x0 SGSIZE Segment Size 0 8 read-only FCCOB0 Flash Common Command Object Registers 0x1A 8 read-write n 0x0 0x0 CCOBn The FCCOB register provides a command code and relevant parameters to the memory controller 0 8 read-write FCCOB1 Flash Common Command Object Registers 0x13 8 read-write n 0x0 0x0 CCOBn The FCCOB register provides a command code and relevant parameters to the memory controller 0 8 read-write FCCOB2 Flash Common Command Object Registers 0xD 8 read-write n 0x0 0x0 CCOBn The FCCOB register provides a command code and relevant parameters to the memory controller 0 8 read-write FCCOB3 Flash Common Command Object Registers 0x8 8 read-write n 0x0 0x0 CCOBn The FCCOB register provides a command code and relevant parameters to the memory controller 0 8 read-write FCCOB4 Flash Common Command Object Registers 0x40 8 read-write n 0x0 0x0 CCOBn The FCCOB register provides a command code and relevant parameters to the memory controller 0 8 read-write FCCOB5 Flash Common Command Object Registers 0x35 8 read-write n 0x0 0x0 CCOBn The FCCOB register provides a command code and relevant parameters to the memory controller 0 8 read-write FCCOB6 Flash Common Command Object Registers 0x2B 8 read-write n 0x0 0x0 CCOBn The FCCOB register provides a command code and relevant parameters to the memory controller 0 8 read-write FCCOB7 Flash Common Command Object Registers 0x22 8 read-write n 0x0 0x0 CCOBn The FCCOB register provides a command code and relevant parameters to the memory controller 0 8 read-write FCCOB8 Flash Common Command Object Registers 0x76 8 read-write n 0x0 0x0 CCOBn The FCCOB register provides a command code and relevant parameters to the memory controller 0 8 read-write FCCOB9 Flash Common Command Object Registers 0x67 8 read-write n 0x0 0x0 CCOBn The FCCOB register provides a command code and relevant parameters to the memory controller 0 8 read-write FCCOBA Flash Common Command Object Registers 0x59 8 read-write n 0x0 0x0 CCOBn The FCCOB register provides a command code and relevant parameters to the memory controller 0 8 read-write FCCOBB Flash Common Command Object Registers 0x4C 8 read-write n 0x0 0x0 CCOBn The FCCOB register provides a command code and relevant parameters to the memory controller 0 8 read-write FCNFG Flash Configuration Register 0x1 8 read-write n 0x0 0x0 CCIE Command Complete Interrupt Enable 7 1 read-write 0 Command complete interrupt disabled #0 1 Command complete interrupt enabled. An interrupt request is generated whenever the FSTAT[CCIF] flag is set. #1 ERSAREQ Erase All Request 5 1 read-only 0 No request or request complete #0 1 Request to: run the Erase All Blocks command, verify the erased state, program the security byte in the Flash Configuration Field to the unsecure state, and release MCU security by setting the FSEC[SEC] field to the unsecure state. #1 ERSSUSP Erase Suspend 4 1 read-write 0 No suspend requested #0 1 Suspend the current Erase Flash Sector command execution. #1 RDCOLLIE Read Collision Error Interrupt Enable 6 1 read-write 0 Read collision error interrupt disabled #0 1 Read collision error interrupt enabled. An interrupt request is generated whenever a flash memory read collision error is detected (see the description of FSTAT[RDCOLERR]). #1 FOPT Flash Option Register 0x3 8 read-only n 0x0 0x0 OPT Nonvolatile Option 0 8 read-only FPROT0 Program Flash Protection Registers 0x56 8 read-write n 0x0 0x0 PROT Program Flash Region Protect 0 8 read-write 0 Program flash region is protected. #0 1 Program flash region is not protected #1 FPROT1 Program Flash Protection Registers 0x43 8 read-write n 0x0 0x0 PROT Program Flash Region Protect 0 8 read-write 0 Program flash region is protected. #0 1 Program flash region is not protected #1 FPROT2 Program Flash Protection Registers 0x31 8 read-write n 0x0 0x0 PROT Program Flash Region Protect 0 8 read-write 0 Program flash region is protected. #0 1 Program flash region is not protected #1 FPROT3 Program Flash Protection Registers 0x20 8 read-write n 0x0 0x0 PROT Program Flash Region Protect 0 8 read-write 0 Program flash region is protected. #0 1 Program flash region is not protected #1 FSEC Flash Security Register 0x2 8 read-only n 0x0 0x0 FSLACC Freescale Failure Analysis Access Code 2 2 read-only 00 Freescale factory access granted #00 01 Freescale factory access denied #01 10 Freescale factory access denied #10 11 Freescale factory access granted #11 KEYEN Backdoor Key Security Enable 6 2 read-only 00 Backdoor key access disabled #00 01 Backdoor key access disabled (preferred KEYEN state to disable backdoor key access) #01 10 Backdoor key access enabled #10 11 Backdoor key access disabled #11 MEEN Mass Erase Enable Bits 4 2 read-only 00 Mass erase is enabled #00 01 Mass erase is enabled #01 10 Mass erase is disabled #10 11 Mass erase is enabled #11 SEC Flash Security 0 2 read-only 00 MCU security status is secure. #00 01 MCU security status is secure. #01 10 MCU security status is unsecure. (The standard shipping condition of the flash memory module is unsecure.) #10 11 MCU security status is secure. #11 FSTAT Flash Status Register 0x0 8 read-write n 0x0 0x0 ACCERR Flash Access Error Flag 5 1 read-write 0 No access error detected #0 1 Access error detected #1 CCIF Command Complete Interrupt Flag 7 1 read-write 0 Flash command in progress #0 1 Flash command has completed #1 FPVIOL Flash Protection Violation Flag 4 1 read-write 0 No protection violation detected #0 1 Protection violation detected #1 MGSTAT0 Memory Controller Command Completion Status Flag 0 1 read-only RDCOLERR Flash Read Collision Error Flag 6 1 read-write 0 No collision error detected #0 1 Collision error detected #1 SACCH0 Supervisor-only Access Registers 0xA6 8 read-only n 0x0 0x0 SA Supervisor-only access control 0 8 read-only 0 Associated segment is accessible in supervisor mode only #0 1 Associated segment is accessible in user or supervisor mode #1 SACCH1 Supervisor-only Access Registers 0x83 8 read-only n 0x0 0x0 SA Supervisor-only access control 0 8 read-only 0 Associated segment is accessible in supervisor mode only #0 1 Associated segment is accessible in user or supervisor mode #1 SACCH2 Supervisor-only Access Registers 0x61 8 read-only n 0x0 0x0 SA Supervisor-only access control 0 8 read-only 0 Associated segment is accessible in supervisor mode only #0 1 Associated segment is accessible in user or supervisor mode #1 SACCH3 Supervisor-only Access Registers 0x40 8 read-only n 0x0 0x0 SA Supervisor-only access control 0 8 read-only 0 Associated segment is accessible in supervisor mode only #0 1 Associated segment is accessible in user or supervisor mode #1 SACCL0 Supervisor-only Access Registers 0x13C 8 read-only n 0x0 0x0 SA Supervisor-only access control 0 8 read-only 0 Associated segment is accessible in supervisor mode only #0 1 Associated segment is accessible in user or supervisor mode #1 SACCL1 Supervisor-only Access Registers 0x115 8 read-only n 0x0 0x0 SA Supervisor-only access control 0 8 read-only 0 Associated segment is accessible in supervisor mode only #0 1 Associated segment is accessible in user or supervisor mode #1 SACCL2 Supervisor-only Access Registers 0xEF 8 read-only n 0x0 0x0 SA Supervisor-only access control 0 8 read-only 0 Associated segment is accessible in supervisor mode only #0 1 Associated segment is accessible in user or supervisor mode #1 SACCL3 Supervisor-only Access Registers 0xCA 8 read-only n 0x0 0x0 SA Supervisor-only access control 0 8 read-only 0 Associated segment is accessible in supervisor mode only #0 1 Associated segment is accessible in user or supervisor mode #1 XACCH0 Execute-only Access Registers 0x7E 8 read-only n 0x0 0x0 XA Execute-only access control 0 8 read-only 0 Associated segment is accessible in execute mode only (as an instruction fetch) #0 1 Associated segment is accessible as data or in execute mode #1 XACCH1 Execute-only Access Registers 0x63 8 read-only n 0x0 0x0 XA Execute-only access control 0 8 read-only 0 Associated segment is accessible in execute mode only (as an instruction fetch) #0 1 Associated segment is accessible as data or in execute mode #1 XACCH2 Execute-only Access Registers 0x49 8 read-only n 0x0 0x0 XA Execute-only access control 0 8 read-only 0 Associated segment is accessible in execute mode only (as an instruction fetch) #0 1 Associated segment is accessible as data or in execute mode #1 XACCH3 Execute-only Access Registers 0x30 8 read-only n 0x0 0x0 XA Execute-only access control 0 8 read-only 0 Associated segment is accessible in execute mode only (as an instruction fetch) #0 1 Associated segment is accessible as data or in execute mode #1 XACCL0 Execute-only Access Registers 0xF4 8 read-only n 0x0 0x0 XA Execute-only access control 0 8 read-only 0 Associated segment is accessible in execute mode only (as an instruction fetch) #0 1 Associated segment is accessible as data or in execute mode #1 XACCL1 Execute-only Access Registers 0xD5 8 read-only n 0x0 0x0 XA Execute-only access control 0 8 read-only 0 Associated segment is accessible in execute mode only (as an instruction fetch) #0 1 Associated segment is accessible as data or in execute mode #1 XACCL2 Execute-only Access Registers 0xB7 8 read-only n 0x0 0x0 XA Execute-only access control 0 8 read-only 0 Associated segment is accessible in execute mode only (as an instruction fetch) #0 1 Associated segment is accessible as data or in execute mode #1 XACCL3 Execute-only Access Registers 0x9A 8 read-only n 0x0 0x0 XA Execute-only access control 0 8 read-only 0 Associated segment is accessible in execute mode only (as an instruction fetch) #0 1 Associated segment is accessible as data or in execute mode #1 FTFA_FlashConfig Flash configuration field FTFA_FlashConfig 0x0 0x0 0xE registers n BACKKEY0 Backdoor Comparison Key 0. 0x3 8 read-only n 0x0 0x0 KEY Backdoor Comparison Key. 0 8 read-only BACKKEY1 Backdoor Comparison Key 1. 0x2 8 read-only n 0x0 0x0 KEY Backdoor Comparison Key. 0 8 read-only BACKKEY2 Backdoor Comparison Key 2. 0x1 8 read-only n 0x0 0x0 KEY Backdoor Comparison Key. 0 8 read-only BACKKEY3 Backdoor Comparison Key 3. 0x0 8 read-only n 0x0 0x0 KEY Backdoor Comparison Key. 0 8 read-only BACKKEY4 Backdoor Comparison Key 4. 0x7 8 read-only n 0x0 0x0 KEY Backdoor Comparison Key. 0 8 read-only BACKKEY5 Backdoor Comparison Key 5. 0x6 8 read-only n 0x0 0x0 KEY Backdoor Comparison Key. 0 8 read-only BACKKEY6 Backdoor Comparison Key 6. 0x5 8 read-only n 0x0 0x0 KEY Backdoor Comparison Key. 0 8 read-only BACKKEY7 Backdoor Comparison Key 7. 0x4 8 read-only n 0x0 0x0 KEY Backdoor Comparison Key. 0 8 read-only FOPT Non-volatile Flash Option Register 0xD 8 read-only n 0x0 0x0 EZPORT_DIS no description available 1 1 read-only 00 EzPort operation is disabled #00 01 EzPort operation is enabled #01 FAST_INIT no description available 5 1 read-only 00 Slower initialization #00 01 Fast Initialization #01 LPBOOT no description available 0 1 read-only 00 Low-power boot #00 01 Normal boot #01 NMI_DIS no description available 2 1 read-only 00 NMI interrupts are always blocked #00 01 NMI_b pin/interrupts reset default to enabled #01 FPROT0 Non-volatile P-Flash Protection 0 - High Register 0xB 8 read-only n 0x0 0x0 PROT P-Flash Region Protect 0 8 read-only FPROT1 Non-volatile P-Flash Protection 0 - Low Register 0xA 8 read-only n 0x0 0x0 PROT P-Flash Region Protect 0 8 read-only FPROT2 Non-volatile P-Flash Protection 1 - High Register 0x9 8 read-only n 0x0 0x0 PROT P-Flash Region Protect 0 8 read-only FPROT3 Non-volatile P-Flash Protection 1 - Low Register 0x8 8 read-only n 0x0 0x0 PROT P-Flash Region Protect 0 8 read-only FSEC Non-volatile Flash Security Register 0xC 8 read-only n 0x0 0x0 FSLACC Freescale Failure Analysis Access Code 2 2 read-only 10 Freescale factory access denied #10 11 Freescale factory access granted #11 KEYEN Backdoor Key Security Enable 6 2 read-only 10 Backdoor key access enabled #10 11 Backdoor key access disabled #11 MEEN no description available 4 2 read-only 10 Mass erase is disabled #10 11 Mass erase is enabled #11 SEC Flash Security 0 2 read-only 10 MCU security status is unsecure #10 11 MCU security status is secure #11 NV_BACKKEY0 Backdoor Comparison Key 0. 0x3 8 read-only n 0x0 0x0 KEY Backdoor Comparison Key. 0 8 read-only NV_BACKKEY1 Backdoor Comparison Key 1. 0x2 8 read-only n 0x0 0x0 KEY Backdoor Comparison Key. 0 8 read-only NV_BACKKEY2 Backdoor Comparison Key 2. 0x1 8 read-only n 0x0 0x0 KEY Backdoor Comparison Key. 0 8 read-only NV_BACKKEY3 Backdoor Comparison Key 3. 0x0 8 read-only n 0x0 0x0 KEY Backdoor Comparison Key. 0 8 read-only NV_BACKKEY4 Backdoor Comparison Key 4. 0x7 8 read-only n 0x0 0x0 KEY Backdoor Comparison Key. 0 8 read-only NV_BACKKEY5 Backdoor Comparison Key 5. 0x6 8 read-only n 0x0 0x0 KEY Backdoor Comparison Key. 0 8 read-only NV_BACKKEY6 Backdoor Comparison Key 6. 0x5 8 read-only n 0x0 0x0 KEY Backdoor Comparison Key. 0 8 read-only NV_BACKKEY7 Backdoor Comparison Key 7. 0x4 8 read-only n 0x0 0x0 KEY Backdoor Comparison Key. 0 8 read-only NV_FOPT Non-volatile Flash Option Register 0xD 8 read-only n 0x0 0x0 EZPORT_DIS no description available 1 1 read-only 00 EzPort operation is disabled #0 01 EzPort operation is enabled #1 FAST_INIT no description available 5 1 read-only 00 Slower initialization #0 01 Fast Initialization #1 LPBOOT no description available 0 1 read-only 00 Low-power boot #0 01 Normal boot #1 NMI_DIS no description available 2 1 read-only 00 NMI interrupts are always blocked #0 01 NMI_b pin/interrupts reset default to enabled #1 NV_FPROT0 Non-volatile P-Flash Protection 0 - High Register 0xB 8 read-only n 0x0 0x0 PROT P-Flash Region Protect 0 8 read-only NV_FPROT1 Non-volatile P-Flash Protection 0 - Low Register 0xA 8 read-only n 0x0 0x0 PROT P-Flash Region Protect 0 8 read-only NV_FPROT2 Non-volatile P-Flash Protection 1 - High Register 0x9 8 read-only n 0x0 0x0 PROT P-Flash Region Protect 0 8 read-only NV_FPROT3 Non-volatile P-Flash Protection 1 - Low Register 0x8 8 read-only n 0x0 0x0 PROT P-Flash Region Protect 0 8 read-only NV_FSEC Non-volatile Flash Security Register 0xC 8 read-only n 0x0 0x0 FSLACC Freescale Failure Analysis Access Code 2 2 read-only 10 Freescale factory access denied #10 11 Freescale factory access granted #11 KEYEN Backdoor Key Security Enable 6 2 read-only 10 Backdoor key access enabled #10 11 Backdoor key access disabled #11 MEEN no description available 4 2 read-only 10 Mass erase is disabled #10 11 Mass erase is enabled #11 SEC Flash Security 0 2 read-only 10 MCU security status is unsecure #10 11 MCU security status is secure #11 FTM0 FlexTimer Module FTM 0x0 0x0 0x9C registers n FTM0 42 C0SC Channel (n) Status And Control 0x18 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C0V Channel (n) Value 0x20 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write C1SC Channel (n) Status And Control 0x2C 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C1V Channel (n) Value 0x38 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write C2SC Channel (n) Status And Control 0x48 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C2V Channel (n) Value 0x58 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write C3SC Channel (n) Status And Control 0x6C 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C3V Channel (n) Value 0x80 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write C4SC Channel (n) Status And Control 0x98 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C4V Channel (n) Value 0xB0 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write C5SC Channel (n) Status And Control 0xCC 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C5V Channel (n) Value 0xE8 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write C6SC Channel (n) Status And Control 0x108 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C6V Channel (n) Value 0x128 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write C7SC Channel (n) Status And Control 0x14C 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C7V Channel (n) Value 0x170 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write CNT Counter 0x4 32 read-write n 0x0 0x0 COUNT Counter Value 0 16 read-write CNTIN Counter Initial Value 0x4C 32 read-write n 0x0 0x0 INIT Initial Value Of The FTM Counter 0 16 read-write COMBINE Function For Linked Channels 0x64 32 read-write n 0x0 0x0 COMBINE0 Combine Channels For n = 0 0 1 read-write 0 Channels (n) and (n+1) are independent. #0 1 Channels (n) and (n+1) are combined. #1 COMBINE1 Combine Channels For n = 2 8 1 read-write 0 Channels (n) and (n+1) are independent. #0 1 Channels (n) and (n+1) are combined. #1 COMBINE2 Combine Channels For n = 4 16 1 read-write 0 Channels (n) and (n+1) are independent. #0 1 Channels (n) and (n+1) are combined. #1 COMBINE3 Combine Channels For n = 6 24 1 read-write 0 Channels (n) and (n+1) are independent. #0 1 Channels (n) and (n+1) are combined. #1 COMP0 Complement Of Channel (n) For n = 0 1 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 COMP1 Complement Of Channel (n) For n = 2 9 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 COMP2 Complement Of Channel (n) For n = 4 17 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 COMP3 Complement Of Channel (n) for n = 6 25 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 DECAP0 Dual Edge Capture Mode Captures For n = 0 3 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DECAP1 Dual Edge Capture Mode Captures For n = 2 11 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DECAP2 Dual Edge Capture Mode Captures For n = 4 19 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DECAP3 Dual Edge Capture Mode Captures For n = 6 27 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DECAPEN0 Dual Edge Capture Mode Enable For n = 0 2 1 read-write 0 The Dual Edge Capture mode in this pair of channels is disabled. #0 1 The Dual Edge Capture mode in this pair of channels is enabled. #1 DECAPEN1 Dual Edge Capture Mode Enable For n = 2 10 1 read-write 0 The Dual Edge Capture mode in this pair of channels is disabled. #0 1 The Dual Edge Capture mode in this pair of channels is enabled. #1 DECAPEN2 Dual Edge Capture Mode Enable For n = 4 18 1 read-write 0 The Dual Edge Capture mode in this pair of channels is disabled. #0 1 The Dual Edge Capture mode in this pair of channels is enabled. #1 DECAPEN3 Dual Edge Capture Mode Enable For n = 6 26 1 read-write 0 The Dual Edge Capture mode in this pair of channels is disabled. #0 1 The Dual Edge Capture mode in this pair of channels is enabled. #1 DTEN0 Deadtime Enable For n = 0 4 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 DTEN1 Deadtime Enable For n = 2 12 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 DTEN2 Deadtime Enable For n = 4 20 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 DTEN3 Deadtime Enable For n = 6 28 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 FAULTEN0 Fault Control Enable For n = 0 6 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 FAULTEN1 Fault Control Enable For n = 2 14 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 FAULTEN2 Fault Control Enable For n = 4 22 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 FAULTEN3 Fault Control Enable For n = 6 30 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 SYNCEN0 Synchronization Enable For n = 0 5 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 SYNCEN1 Synchronization Enable For n = 2 13 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 SYNCEN2 Synchronization Enable For n = 4 21 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 SYNCEN3 Synchronization Enable For n = 6 29 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 CONF Configuration 0x84 32 read-write n 0x0 0x0 BDMMODE BDM Mode 6 2 read-write GTBEEN Global Time Base Enable 9 1 read-write 0 Use of an external global time base is disabled. #0 1 Use of an external global time base is enabled. #1 GTBEOUT Global Time Base Output 10 1 read-write 0 A global time base signal generation is disabled. #0 1 A global time base signal generation is enabled. #1 NUMTOF TOF Frequency 0 5 read-write DEADTIME Deadtime Insertion Control 0x68 32 read-write n 0x0 0x0 DTPS Deadtime Prescaler Value 6 2 read-write 10 Divide the system clock by 4. #10 11 Divide the system clock by 16. #11 DTVAL Deadtime Value 0 6 read-write EXTTRIG FTM External Trigger 0x6C 32 read-write n 0x0 0x0 CH0TRIG Channel 0 Trigger Enable 4 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH1TRIG Channel 1 Trigger Enable 5 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH2TRIG Channel 2 Trigger Enable 0 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH3TRIG Channel 3 Trigger Enable 1 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH4TRIG Channel 4 Trigger Enable 2 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH5TRIG Channel 5 Trigger Enable 3 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 INITTRIGEN Initialization Trigger Enable 6 1 read-write 0 The generation of initialization trigger is disabled. #0 1 The generation of initialization trigger is enabled. #1 TRIGF Channel Trigger Flag 7 1 read-write 0 No channel trigger was generated. #0 1 A channel trigger was generated. #1 FILTER Input Capture Filter Control 0x78 32 read-write n 0x0 0x0 CH0FVAL Channel 0 Input Filter 0 4 read-write CH1FVAL Channel 1 Input Filter 4 4 read-write CH2FVAL Channel 2 Input Filter 8 4 read-write CH3FVAL Channel 3 Input Filter 12 4 read-write FLTCTRL Fault Control 0x7C 32 read-write n 0x0 0x0 FAULT0EN Fault Input 0 Enable 0 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT1EN Fault Input 1 Enable 1 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT2EN Fault Input 2 Enable 2 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT3EN Fault Input 3 Enable 3 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FFLTR0EN Fault Input 0 Filter Enable 4 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR1EN Fault Input 1 Filter Enable 5 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR2EN Fault Input 2 Filter Enable 6 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR3EN Fault Input 3 Filter Enable 7 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFVAL Fault Input Filter 8 4 read-write FLTPOL FTM Fault Input Polarity 0x88 32 read-write n 0x0 0x0 FLT0POL Fault Input 0 Polarity 0 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT1POL Fault Input 1 Polarity 1 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT2POL Fault Input 2 Polarity 2 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT3POL Fault Input 3 Polarity 3 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FMS Fault Mode Status 0x74 32 read-write n 0x0 0x0 FAULTF Fault Detection Flag 7 1 read-write 0 No fault condition was detected. #0 1 A fault condition was detected. #1 FAULTF0 Fault Detection Flag 0 0 1 read-write 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF1 Fault Detection Flag 1 1 1 read-write 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF2 Fault Detection Flag 2 2 1 read-write 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF3 Fault Detection Flag 3 3 1 read-write 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTIN Fault Inputs 5 1 read-only 0 The logic OR of the enabled fault inputs is 0. #0 1 The logic OR of the enabled fault inputs is 1. #1 WPEN Write Protection Enable 6 1 read-write 0 Write protection is disabled. Write protected bits can be written. #0 1 Write protection is enabled. Write protected bits cannot be written. #1 INVCTRL FTM Inverting Control 0x90 32 read-write n 0x0 0x0 INV0EN Pair Channels 0 Inverting Enable 0 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV1EN Pair Channels 1 Inverting Enable 1 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV2EN Pair Channels 2 Inverting Enable 2 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV3EN Pair Channels 3 Inverting Enable 3 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 MOD Modulo 0x8 32 read-write n 0x0 0x0 MOD Modulo Value 0 16 read-write MODE Features Mode Selection 0x54 32 read-write n 0x0 0x0 CAPTEST Capture Test Mode Enable 4 1 read-write 0 Capture test mode is disabled. #0 1 Capture test mode is enabled. #1 FAULTIE Fault Interrupt Enable 7 1 read-write 0 Fault control interrupt is disabled. #0 1 Fault control interrupt is enabled. #1 FAULTM Fault Control Mode 5 2 read-write 00 Fault control is disabled for all channels. #00 01 Fault control is enabled for even channels only (channels 0, 2, 4, and 6), and the selected mode is the manual fault clearing. #01 10 Fault control is enabled for all channels, and the selected mode is the manual fault clearing. #10 11 Fault control is enabled for all channels, and the selected mode is the automatic fault clearing. #11 FTMEN FTM Enable 0 1 read-write 0 Only the TPM-compatible registers (first set of registers) can be used without any restriction. Do not use the FTM-specific registers. #0 1 All registers including the FTM-specific registers (second set of registers) are available for use with no restrictions. #1 INIT Initialize The Channels Output 1 1 read-write PWMSYNC PWM Synchronization Mode 3 1 read-write 0 No restrictions. Software and hardware triggers can be used by MOD, CnV, OUTMASK, and FTM counter synchronization. #0 1 Software trigger can only be used by MOD and CnV synchronization, and hardware triggers can only be used by OUTMASK and FTM counter synchronization. #1 WPDIS Write Protection Disable 2 1 read-write 0 Write protection is enabled. #0 1 Write protection is disabled. #1 OUTINIT Initial State For Channels Output 0x5C 32 read-write n 0x0 0x0 CH0OI Channel 0 Output Initialization Value 0 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH1OI Channel 1 Output Initialization Value 1 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH2OI Channel 2 Output Initialization Value 2 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH3OI Channel 3 Output Initialization Value 3 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH4OI Channel 4 Output Initialization Value 4 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH5OI Channel 5 Output Initialization Value 5 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH6OI Channel 6 Output Initialization Value 6 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH7OI Channel 7 Output Initialization Value 7 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 OUTMASK Output Mask 0x60 32 read-write n 0x0 0x0 CH0OM Channel 0 Output Mask 0 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH1OM Channel 1 Output Mask 1 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH2OM Channel 2 Output Mask 2 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH3OM Channel 3 Output Mask 3 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH4OM Channel 4 Output Mask 4 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH5OM Channel 5 Output Mask 5 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH6OM Channel 6 Output Mask 6 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH7OM Channel 7 Output Mask 7 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 POL Channels Polarity 0x70 32 read-write n 0x0 0x0 POL0 Channel 0 Polarity 0 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL1 Channel 1 Polarity 1 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL2 Channel 2 Polarity 2 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL3 Channel 3 Polarity 3 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL4 Channel 4 Polarity 4 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL5 Channel 5 Polarity 5 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL6 Channel 6 Polarity 6 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL7 Channel 7 Polarity 7 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 PWMLOAD FTM PWM Load 0x98 32 read-write n 0x0 0x0 CH0SEL Channel 0 Select 0 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH1SEL Channel 1 Select 1 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH2SEL Channel 2 Select 2 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH3SEL Channel 3 Select 3 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH4SEL Channel 4 Select 4 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH5SEL Channel 5 Select 5 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH6SEL Channel 6 Select 6 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH7SEL Channel 7 Select 7 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 LDOK Load Enable 9 1 read-write 0 Loading updated values is disabled. #0 1 Loading updated values is enabled. #1 QDCTRL Quadrature Decoder Control And Status 0x80 32 read-write n 0x0 0x0 PHAFLTREN Phase A Input Filter Enable 7 1 read-write 0 Phase A input filter is disabled. #0 1 Phase A input filter is enabled. #1 PHAPOL Phase A Input Polarity 5 1 read-write 0 Normal polarity. Phase A input signal is not inverted before identifying the rising and falling edges of this signal. #0 1 Inverted polarity. Phase A input signal is inverted before identifying the rising and falling edges of this signal. #1 PHBFLTREN Phase B Input Filter Enable 6 1 read-write 0 Phase B input filter is disabled. #0 1 Phase B input filter is enabled. #1 PHBPOL Phase B Input Polarity 4 1 read-write 0 Normal polarity. Phase B input signal is not inverted before identifying the rising and falling edges of this signal. #0 1 Inverted polarity. Phase B input signal is inverted before identifying the rising and falling edges of this signal. #1 QUADEN Quadrature Decoder Mode Enable 0 1 read-write 0 Quadrature Decoder mode is disabled. #0 1 Quadrature Decoder mode is enabled. #1 QUADIR FTM Counter Direction In Quadrature Decoder Mode 2 1 read-only 0 Counting direction is decreasing (FTM counter decrement). #0 1 Counting direction is increasing (FTM counter increment). #1 QUADMODE Quadrature Decoder Mode 3 1 read-write 0 Phase A and phase B encoding mode. #0 1 Count and direction encoding mode. #1 TOFDIR Timer Overflow Direction In Quadrature Decoder Mode 1 1 read-only 0 TOF bit was set on the bottom of counting. There was an FTM counter decrement and FTM counter changes from its minimum value (CNTIN register) to its maximum value (MOD register). #0 1 TOF bit was set on the top of counting. There was an FTM counter increment and FTM counter changes from its maximum value (MOD register) to its minimum value (CNTIN register). #1 SC Status And Control 0x0 32 read-write n 0x0 0x0 CLKS Clock Source Selection 3 2 read-write 00 No clock selected. This in effect disables the FTM counter. #00 01 System clock #01 10 Fixed frequency clock #10 11 External clock #11 CPWMS Center-Aligned PWM Select 5 1 read-write 0 FTM counter operates in Up Counting mode. #0 1 FTM counter operates in Up-Down Counting mode. #1 PS Prescale Factor Selection 0 3 read-write 000 Divide by 1 #000 001 Divide by 2 #001 010 Divide by 4 #010 011 Divide by 8 #011 100 Divide by 16 #100 101 Divide by 32 #101 110 Divide by 64 #110 111 Divide by 128 #111 TOF Timer Overflow Flag 7 1 read-write 0 FTM counter has not overflowed. #0 1 FTM counter has overflowed. #1 TOIE Timer Overflow Interrupt Enable 6 1 read-write 0 Disable TOF interrupts. Use software polling. #0 1 Enable TOF interrupts. An interrupt is generated when TOF equals one. #1 STATUS Capture And Compare Status 0x50 32 read-write n 0x0 0x0 CH0F Channel 0 Flag 0 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH1F Channel 1 Flag 1 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH2F Channel 2 Flag 2 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH3F Channel 3 Flag 3 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH4F Channel 4 Flag 4 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH5F Channel 5 Flag 5 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH6F Channel 6 Flag 6 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH7F Channel 7 Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 SWOCTRL FTM Software Output Control 0x94 32 read-write n 0x0 0x0 CH0OC Channel 0 Software Output Control Enable 0 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH0OCV Channel 0 Software Output Control Value 8 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH1OC Channel 1 Software Output Control Enable 1 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH1OCV Channel 1 Software Output Control Value 9 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH2OC Channel 2 Software Output Control Enable 2 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH2OCV Channel 2 Software Output Control Value 10 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH3OC Channel 3 Software Output Control Enable 3 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH3OCV Channel 3 Software Output Control Value 11 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH4OC Channel 4 Software Output Control Enable 4 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH4OCV Channel 4 Software Output Control Value 12 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH5OC Channel 5 Software Output Control Enable 5 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH5OCV Channel 5 Software Output Control Value 13 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH6OC Channel 6 Software Output Control Enable 6 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH6OCV Channel 6 Software Output Control Value 14 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH7OC Channel 7 Software Output Control Enable 7 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH7OCV Channel 7 Software Output Control Value 15 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 SYNC Synchronization 0x58 32 read-write n 0x0 0x0 CNTMAX Maximum Loading Point Enable 1 1 read-write 0 The maximum loading point is disabled. #0 1 The maximum loading point is enabled. #1 CNTMIN Minimum Loading Point Enable 0 1 read-write 0 The minimum loading point is disabled. #0 1 The minimum loading point is enabled. #1 REINIT FTM Counter Reinitialization By Synchronization (FTM counter synchronization) 2 1 read-write 0 FTM counter continues to count normally. #0 1 FTM counter is updated with its initial value when the selected trigger is detected. #1 SWSYNC PWM Synchronization Software Trigger 7 1 read-write 0 Software trigger is not selected. #0 1 Software trigger is selected. #1 SYNCHOM Output Mask Synchronization 3 1 read-write 0 OUTMASK register is updated with the value of its buffer in all rising edges of the system clock. #0 1 OUTMASK register is updated with the value of its buffer only by the PWM synchronization. #1 TRIG0 PWM Synchronization Hardware Trigger 0 4 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 TRIG1 PWM Synchronization Hardware Trigger 1 5 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 TRIG2 PWM Synchronization Hardware Trigger 2 6 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 SYNCONF Synchronization Configuration 0x8C 32 read-write n 0x0 0x0 CNTINC CNTIN Register Synchronization 2 1 read-write 0 CNTIN register is updated with its buffer value at all rising edges of system clock. #0 1 CNTIN register is updated with its buffer value by the PWM synchronization. #1 HWINVC Inverting control synchronization is activated by a hardware trigger. 19 1 read-write 0 A hardware trigger does not activate the INVCTRL register synchronization. #0 1 A hardware trigger activates the INVCTRL register synchronization. #1 HWOM Output mask synchronization is activated by a hardware trigger. 18 1 read-write 0 A hardware trigger does not activate the OUTMASK register synchronization. #0 1 A hardware trigger activates the OUTMASK register synchronization. #1 HWRSTCNT FTM counter synchronization is activated by a hardware trigger. 16 1 read-write 0 A hardware trigger does not activate the FTM counter synchronization. #0 1 A hardware trigger activates the FTM counter synchronization. #1 HWSOC Software output control synchronization is activated by a hardware trigger. 20 1 read-write 0 A hardware trigger does not activate the SWOCTRL register synchronization. #0 1 A hardware trigger activates the SWOCTRL register synchronization. #1 HWTRIGMODE Hardware Trigger Mode 0 1 read-write 0 FTM clears the TRIGj bit when the hardware trigger j is detected, where j = 0, 1,2. #0 1 FTM does not clear the TRIGj bit when the hardware trigger j is detected, where j = 0, 1,2. #1 HWWRBUF MOD, CNTIN, and CV registers synchronization is activated by a hardware trigger. 17 1 read-write 0 A hardware trigger does not activate MOD, CNTIN, and CV registers synchronization. #0 1 A hardware trigger activates MOD, CNTIN, and CV registers synchronization. #1 INVC INVCTRL Register Synchronization 4 1 read-write 0 INVCTRL register is updated with its buffer value at all rising edges of system clock. #0 1 INVCTRL register is updated with its buffer value by the PWM synchronization. #1 SWINVC Inverting control synchronization is activated by the software trigger. 11 1 read-write 0 The software trigger does not activate the INVCTRL register synchronization. #0 1 The software trigger activates the INVCTRL register synchronization. #1 SWOC SWOCTRL Register Synchronization 5 1 read-write 0 SWOCTRL register is updated with its buffer value at all rising edges of system clock. #0 1 SWOCTRL register is updated with its buffer value by the PWM synchronization. #1 SWOM Output mask synchronization is activated by the software trigger. 10 1 read-write 0 The software trigger does not activate the OUTMASK register synchronization. #0 1 The software trigger activates the OUTMASK register synchronization. #1 SWRSTCNT FTM counter synchronization is activated by the software trigger. 8 1 read-write 0 The software trigger does not activate the FTM counter synchronization. #0 1 The software trigger activates the FTM counter synchronization. #1 SWSOC Software output control synchronization is activated by the software trigger. 12 1 read-write 0 The software trigger does not activate the SWOCTRL register synchronization. #0 1 The software trigger activates the SWOCTRL register synchronization. #1 SWWRBUF MOD, CNTIN, and CV registers synchronization is activated by the software trigger. 9 1 read-write 0 The software trigger does not activate MOD, CNTIN, and CV registers synchronization. #0 1 The software trigger activates MOD, CNTIN, and CV registers synchronization. #1 SYNCMODE Synchronization Mode 7 1 read-write 0 Legacy PWM synchronization is selected. #0 1 Enhanced PWM synchronization is selected. #1 FTM1 FlexTimer Module FTM 0x0 0x0 0x9C registers n FTM1 43 C0SC Channel (n) Status And Control 0x18 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C0V Channel (n) Value 0x20 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write C1SC Channel (n) Status And Control 0x2C 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C1V Channel (n) Value 0x38 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write CNT Counter 0x4 32 read-write n 0x0 0x0 COUNT Counter Value 0 16 read-write CNTIN Counter Initial Value 0x4C 32 read-write n 0x0 0x0 INIT Initial Value Of The FTM Counter 0 16 read-write COMBINE Function For Linked Channels 0x64 32 read-write n 0x0 0x0 COMBINE0 Combine Channels For n = 0 0 1 read-write 0 Channels (n) and (n+1) are independent. #0 1 Channels (n) and (n+1) are combined. #1 COMBINE1 Combine Channels For n = 2 8 1 read-write 0 Channels (n) and (n+1) are independent. #0 1 Channels (n) and (n+1) are combined. #1 COMBINE2 Combine Channels For n = 4 16 1 read-write 0 Channels (n) and (n+1) are independent. #0 1 Channels (n) and (n+1) are combined. #1 COMBINE3 Combine Channels For n = 6 24 1 read-write 0 Channels (n) and (n+1) are independent. #0 1 Channels (n) and (n+1) are combined. #1 COMP0 Complement Of Channel (n) For n = 0 1 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 COMP1 Complement Of Channel (n) For n = 2 9 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 COMP2 Complement Of Channel (n) For n = 4 17 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 COMP3 Complement Of Channel (n) for n = 6 25 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 DECAP0 Dual Edge Capture Mode Captures For n = 0 3 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DECAP1 Dual Edge Capture Mode Captures For n = 2 11 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DECAP2 Dual Edge Capture Mode Captures For n = 4 19 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DECAP3 Dual Edge Capture Mode Captures For n = 6 27 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DECAPEN0 Dual Edge Capture Mode Enable For n = 0 2 1 read-write 0 The Dual Edge Capture mode in this pair of channels is disabled. #0 1 The Dual Edge Capture mode in this pair of channels is enabled. #1 DECAPEN1 Dual Edge Capture Mode Enable For n = 2 10 1 read-write 0 The Dual Edge Capture mode in this pair of channels is disabled. #0 1 The Dual Edge Capture mode in this pair of channels is enabled. #1 DECAPEN2 Dual Edge Capture Mode Enable For n = 4 18 1 read-write 0 The Dual Edge Capture mode in this pair of channels is disabled. #0 1 The Dual Edge Capture mode in this pair of channels is enabled. #1 DECAPEN3 Dual Edge Capture Mode Enable For n = 6 26 1 read-write 0 The Dual Edge Capture mode in this pair of channels is disabled. #0 1 The Dual Edge Capture mode in this pair of channels is enabled. #1 DTEN0 Deadtime Enable For n = 0 4 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 DTEN1 Deadtime Enable For n = 2 12 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 DTEN2 Deadtime Enable For n = 4 20 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 DTEN3 Deadtime Enable For n = 6 28 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 FAULTEN0 Fault Control Enable For n = 0 6 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 FAULTEN1 Fault Control Enable For n = 2 14 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 FAULTEN2 Fault Control Enable For n = 4 22 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 FAULTEN3 Fault Control Enable For n = 6 30 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 SYNCEN0 Synchronization Enable For n = 0 5 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 SYNCEN1 Synchronization Enable For n = 2 13 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 SYNCEN2 Synchronization Enable For n = 4 21 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 SYNCEN3 Synchronization Enable For n = 6 29 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 CONF Configuration 0x84 32 read-write n 0x0 0x0 BDMMODE BDM Mode 6 2 read-write GTBEEN Global Time Base Enable 9 1 read-write 0 Use of an external global time base is disabled. #0 1 Use of an external global time base is enabled. #1 GTBEOUT Global Time Base Output 10 1 read-write 0 A global time base signal generation is disabled. #0 1 A global time base signal generation is enabled. #1 NUMTOF TOF Frequency 0 5 read-write DEADTIME Deadtime Insertion Control 0x68 32 read-write n 0x0 0x0 DTPS Deadtime Prescaler Value 6 2 read-write 10 Divide the system clock by 4. #10 11 Divide the system clock by 16. #11 DTVAL Deadtime Value 0 6 read-write EXTTRIG FTM External Trigger 0x6C 32 read-write n 0x0 0x0 CH0TRIG Channel 0 Trigger Enable 4 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH1TRIG Channel 1 Trigger Enable 5 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH2TRIG Channel 2 Trigger Enable 0 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH3TRIG Channel 3 Trigger Enable 1 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH4TRIG Channel 4 Trigger Enable 2 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH5TRIG Channel 5 Trigger Enable 3 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 INITTRIGEN Initialization Trigger Enable 6 1 read-write 0 The generation of initialization trigger is disabled. #0 1 The generation of initialization trigger is enabled. #1 TRIGF Channel Trigger Flag 7 1 read-write 0 No channel trigger was generated. #0 1 A channel trigger was generated. #1 FILTER Input Capture Filter Control 0x78 32 read-write n 0x0 0x0 CH0FVAL Channel 0 Input Filter 0 4 read-write CH1FVAL Channel 1 Input Filter 4 4 read-write CH2FVAL Channel 2 Input Filter 8 4 read-write CH3FVAL Channel 3 Input Filter 12 4 read-write FLTCTRL Fault Control 0x7C 32 read-write n 0x0 0x0 FAULT0EN Fault Input 0 Enable 0 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT1EN Fault Input 1 Enable 1 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT2EN Fault Input 2 Enable 2 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT3EN Fault Input 3 Enable 3 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FFLTR0EN Fault Input 0 Filter Enable 4 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR1EN Fault Input 1 Filter Enable 5 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR2EN Fault Input 2 Filter Enable 6 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR3EN Fault Input 3 Filter Enable 7 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFVAL Fault Input Filter 8 4 read-write FLTPOL FTM Fault Input Polarity 0x88 32 read-write n 0x0 0x0 FLT0POL Fault Input 0 Polarity 0 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT1POL Fault Input 1 Polarity 1 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT2POL Fault Input 2 Polarity 2 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT3POL Fault Input 3 Polarity 3 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FMS Fault Mode Status 0x74 32 read-write n 0x0 0x0 FAULTF Fault Detection Flag 7 1 read-write 0 No fault condition was detected. #0 1 A fault condition was detected. #1 FAULTF0 Fault Detection Flag 0 0 1 read-write 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF1 Fault Detection Flag 1 1 1 read-write 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF2 Fault Detection Flag 2 2 1 read-write 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF3 Fault Detection Flag 3 3 1 read-write 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTIN Fault Inputs 5 1 read-only 0 The logic OR of the enabled fault inputs is 0. #0 1 The logic OR of the enabled fault inputs is 1. #1 WPEN Write Protection Enable 6 1 read-write 0 Write protection is disabled. Write protected bits can be written. #0 1 Write protection is enabled. Write protected bits cannot be written. #1 INVCTRL FTM Inverting Control 0x90 32 read-write n 0x0 0x0 INV0EN Pair Channels 0 Inverting Enable 0 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV1EN Pair Channels 1 Inverting Enable 1 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV2EN Pair Channels 2 Inverting Enable 2 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV3EN Pair Channels 3 Inverting Enable 3 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 MOD Modulo 0x8 32 read-write n 0x0 0x0 MOD Modulo Value 0 16 read-write MODE Features Mode Selection 0x54 32 read-write n 0x0 0x0 CAPTEST Capture Test Mode Enable 4 1 read-write 0 Capture test mode is disabled. #0 1 Capture test mode is enabled. #1 FAULTIE Fault Interrupt Enable 7 1 read-write 0 Fault control interrupt is disabled. #0 1 Fault control interrupt is enabled. #1 FAULTM Fault Control Mode 5 2 read-write 00 Fault control is disabled for all channels. #00 01 Fault control is enabled for even channels only (channels 0, 2, 4, and 6), and the selected mode is the manual fault clearing. #01 10 Fault control is enabled for all channels, and the selected mode is the manual fault clearing. #10 11 Fault control is enabled for all channels, and the selected mode is the automatic fault clearing. #11 FTMEN FTM Enable 0 1 read-write 0 Only the TPM-compatible registers (first set of registers) can be used without any restriction. Do not use the FTM-specific registers. #0 1 All registers including the FTM-specific registers (second set of registers) are available for use with no restrictions. #1 INIT Initialize The Channels Output 1 1 read-write PWMSYNC PWM Synchronization Mode 3 1 read-write 0 No restrictions. Software and hardware triggers can be used by MOD, CnV, OUTMASK, and FTM counter synchronization. #0 1 Software trigger can only be used by MOD and CnV synchronization, and hardware triggers can only be used by OUTMASK and FTM counter synchronization. #1 WPDIS Write Protection Disable 2 1 read-write 0 Write protection is enabled. #0 1 Write protection is disabled. #1 OUTINIT Initial State For Channels Output 0x5C 32 read-write n 0x0 0x0 CH0OI Channel 0 Output Initialization Value 0 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH1OI Channel 1 Output Initialization Value 1 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH2OI Channel 2 Output Initialization Value 2 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH3OI Channel 3 Output Initialization Value 3 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH4OI Channel 4 Output Initialization Value 4 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH5OI Channel 5 Output Initialization Value 5 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH6OI Channel 6 Output Initialization Value 6 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH7OI Channel 7 Output Initialization Value 7 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 OUTMASK Output Mask 0x60 32 read-write n 0x0 0x0 CH0OM Channel 0 Output Mask 0 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH1OM Channel 1 Output Mask 1 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH2OM Channel 2 Output Mask 2 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH3OM Channel 3 Output Mask 3 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH4OM Channel 4 Output Mask 4 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH5OM Channel 5 Output Mask 5 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH6OM Channel 6 Output Mask 6 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH7OM Channel 7 Output Mask 7 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 POL Channels Polarity 0x70 32 read-write n 0x0 0x0 POL0 Channel 0 Polarity 0 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL1 Channel 1 Polarity 1 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL2 Channel 2 Polarity 2 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL3 Channel 3 Polarity 3 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL4 Channel 4 Polarity 4 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL5 Channel 5 Polarity 5 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL6 Channel 6 Polarity 6 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL7 Channel 7 Polarity 7 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 PWMLOAD FTM PWM Load 0x98 32 read-write n 0x0 0x0 CH0SEL Channel 0 Select 0 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH1SEL Channel 1 Select 1 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH2SEL Channel 2 Select 2 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH3SEL Channel 3 Select 3 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH4SEL Channel 4 Select 4 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH5SEL Channel 5 Select 5 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH6SEL Channel 6 Select 6 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH7SEL Channel 7 Select 7 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 LDOK Load Enable 9 1 read-write 0 Loading updated values is disabled. #0 1 Loading updated values is enabled. #1 QDCTRL Quadrature Decoder Control And Status 0x80 32 read-write n 0x0 0x0 PHAFLTREN Phase A Input Filter Enable 7 1 read-write 0 Phase A input filter is disabled. #0 1 Phase A input filter is enabled. #1 PHAPOL Phase A Input Polarity 5 1 read-write 0 Normal polarity. Phase A input signal is not inverted before identifying the rising and falling edges of this signal. #0 1 Inverted polarity. Phase A input signal is inverted before identifying the rising and falling edges of this signal. #1 PHBFLTREN Phase B Input Filter Enable 6 1 read-write 0 Phase B input filter is disabled. #0 1 Phase B input filter is enabled. #1 PHBPOL Phase B Input Polarity 4 1 read-write 0 Normal polarity. Phase B input signal is not inverted before identifying the rising and falling edges of this signal. #0 1 Inverted polarity. Phase B input signal is inverted before identifying the rising and falling edges of this signal. #1 QUADEN Quadrature Decoder Mode Enable 0 1 read-write 0 Quadrature Decoder mode is disabled. #0 1 Quadrature Decoder mode is enabled. #1 QUADIR FTM Counter Direction In Quadrature Decoder Mode 2 1 read-only 0 Counting direction is decreasing (FTM counter decrement). #0 1 Counting direction is increasing (FTM counter increment). #1 QUADMODE Quadrature Decoder Mode 3 1 read-write 0 Phase A and phase B encoding mode. #0 1 Count and direction encoding mode. #1 TOFDIR Timer Overflow Direction In Quadrature Decoder Mode 1 1 read-only 0 TOF bit was set on the bottom of counting. There was an FTM counter decrement and FTM counter changes from its minimum value (CNTIN register) to its maximum value (MOD register). #0 1 TOF bit was set on the top of counting. There was an FTM counter increment and FTM counter changes from its maximum value (MOD register) to its minimum value (CNTIN register). #1 SC Status And Control 0x0 32 read-write n 0x0 0x0 CLKS Clock Source Selection 3 2 read-write 00 No clock selected. This in effect disables the FTM counter. #00 01 System clock #01 10 Fixed frequency clock #10 11 External clock #11 CPWMS Center-Aligned PWM Select 5 1 read-write 0 FTM counter operates in Up Counting mode. #0 1 FTM counter operates in Up-Down Counting mode. #1 PS Prescale Factor Selection 0 3 read-write 000 Divide by 1 #000 001 Divide by 2 #001 010 Divide by 4 #010 011 Divide by 8 #011 100 Divide by 16 #100 101 Divide by 32 #101 110 Divide by 64 #110 111 Divide by 128 #111 TOF Timer Overflow Flag 7 1 read-write 0 FTM counter has not overflowed. #0 1 FTM counter has overflowed. #1 TOIE Timer Overflow Interrupt Enable 6 1 read-write 0 Disable TOF interrupts. Use software polling. #0 1 Enable TOF interrupts. An interrupt is generated when TOF equals one. #1 STATUS Capture And Compare Status 0x50 32 read-write n 0x0 0x0 CH0F Channel 0 Flag 0 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH1F Channel 1 Flag 1 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH2F Channel 2 Flag 2 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH3F Channel 3 Flag 3 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH4F Channel 4 Flag 4 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH5F Channel 5 Flag 5 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH6F Channel 6 Flag 6 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH7F Channel 7 Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 SWOCTRL FTM Software Output Control 0x94 32 read-write n 0x0 0x0 CH0OC Channel 0 Software Output Control Enable 0 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH0OCV Channel 0 Software Output Control Value 8 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH1OC Channel 1 Software Output Control Enable 1 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH1OCV Channel 1 Software Output Control Value 9 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH2OC Channel 2 Software Output Control Enable 2 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH2OCV Channel 2 Software Output Control Value 10 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH3OC Channel 3 Software Output Control Enable 3 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH3OCV Channel 3 Software Output Control Value 11 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH4OC Channel 4 Software Output Control Enable 4 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH4OCV Channel 4 Software Output Control Value 12 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH5OC Channel 5 Software Output Control Enable 5 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH5OCV Channel 5 Software Output Control Value 13 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH6OC Channel 6 Software Output Control Enable 6 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH6OCV Channel 6 Software Output Control Value 14 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH7OC Channel 7 Software Output Control Enable 7 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH7OCV Channel 7 Software Output Control Value 15 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 SYNC Synchronization 0x58 32 read-write n 0x0 0x0 CNTMAX Maximum Loading Point Enable 1 1 read-write 0 The maximum loading point is disabled. #0 1 The maximum loading point is enabled. #1 CNTMIN Minimum Loading Point Enable 0 1 read-write 0 The minimum loading point is disabled. #0 1 The minimum loading point is enabled. #1 REINIT FTM Counter Reinitialization By Synchronization (FTM counter synchronization) 2 1 read-write 0 FTM counter continues to count normally. #0 1 FTM counter is updated with its initial value when the selected trigger is detected. #1 SWSYNC PWM Synchronization Software Trigger 7 1 read-write 0 Software trigger is not selected. #0 1 Software trigger is selected. #1 SYNCHOM Output Mask Synchronization 3 1 read-write 0 OUTMASK register is updated with the value of its buffer in all rising edges of the system clock. #0 1 OUTMASK register is updated with the value of its buffer only by the PWM synchronization. #1 TRIG0 PWM Synchronization Hardware Trigger 0 4 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 TRIG1 PWM Synchronization Hardware Trigger 1 5 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 TRIG2 PWM Synchronization Hardware Trigger 2 6 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 SYNCONF Synchronization Configuration 0x8C 32 read-write n 0x0 0x0 CNTINC CNTIN Register Synchronization 2 1 read-write 0 CNTIN register is updated with its buffer value at all rising edges of system clock. #0 1 CNTIN register is updated with its buffer value by the PWM synchronization. #1 HWINVC Inverting control synchronization is activated by a hardware trigger. 19 1 read-write 0 A hardware trigger does not activate the INVCTRL register synchronization. #0 1 A hardware trigger activates the INVCTRL register synchronization. #1 HWOM Output mask synchronization is activated by a hardware trigger. 18 1 read-write 0 A hardware trigger does not activate the OUTMASK register synchronization. #0 1 A hardware trigger activates the OUTMASK register synchronization. #1 HWRSTCNT FTM counter synchronization is activated by a hardware trigger. 16 1 read-write 0 A hardware trigger does not activate the FTM counter synchronization. #0 1 A hardware trigger activates the FTM counter synchronization. #1 HWSOC Software output control synchronization is activated by a hardware trigger. 20 1 read-write 0 A hardware trigger does not activate the SWOCTRL register synchronization. #0 1 A hardware trigger activates the SWOCTRL register synchronization. #1 HWTRIGMODE Hardware Trigger Mode 0 1 read-write 0 FTM clears the TRIGj bit when the hardware trigger j is detected, where j = 0, 1,2. #0 1 FTM does not clear the TRIGj bit when the hardware trigger j is detected, where j = 0, 1,2. #1 HWWRBUF MOD, CNTIN, and CV registers synchronization is activated by a hardware trigger. 17 1 read-write 0 A hardware trigger does not activate MOD, CNTIN, and CV registers synchronization. #0 1 A hardware trigger activates MOD, CNTIN, and CV registers synchronization. #1 INVC INVCTRL Register Synchronization 4 1 read-write 0 INVCTRL register is updated with its buffer value at all rising edges of system clock. #0 1 INVCTRL register is updated with its buffer value by the PWM synchronization. #1 SWINVC Inverting control synchronization is activated by the software trigger. 11 1 read-write 0 The software trigger does not activate the INVCTRL register synchronization. #0 1 The software trigger activates the INVCTRL register synchronization. #1 SWOC SWOCTRL Register Synchronization 5 1 read-write 0 SWOCTRL register is updated with its buffer value at all rising edges of system clock. #0 1 SWOCTRL register is updated with its buffer value by the PWM synchronization. #1 SWOM Output mask synchronization is activated by the software trigger. 10 1 read-write 0 The software trigger does not activate the OUTMASK register synchronization. #0 1 The software trigger activates the OUTMASK register synchronization. #1 SWRSTCNT FTM counter synchronization is activated by the software trigger. 8 1 read-write 0 The software trigger does not activate the FTM counter synchronization. #0 1 The software trigger activates the FTM counter synchronization. #1 SWSOC Software output control synchronization is activated by the software trigger. 12 1 read-write 0 The software trigger does not activate the SWOCTRL register synchronization. #0 1 The software trigger activates the SWOCTRL register synchronization. #1 SWWRBUF MOD, CNTIN, and CV registers synchronization is activated by the software trigger. 9 1 read-write 0 The software trigger does not activate MOD, CNTIN, and CV registers synchronization. #0 1 The software trigger activates MOD, CNTIN, and CV registers synchronization. #1 SYNCMODE Synchronization Mode 7 1 read-write 0 Legacy PWM synchronization is selected. #0 1 Enhanced PWM synchronization is selected. #1 FTM2 FlexTimer Module FTM 0x0 0x0 0x9C registers n FTM2 44 C0SC Channel (n) Status And Control 0x18 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C0V Channel (n) Value 0x20 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write C1SC Channel (n) Status And Control 0x2C 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C1V Channel (n) Value 0x38 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write CNT Counter 0x4 32 read-write n 0x0 0x0 COUNT Counter Value 0 16 read-write CNTIN Counter Initial Value 0x4C 32 read-write n 0x0 0x0 INIT Initial Value Of The FTM Counter 0 16 read-write COMBINE Function For Linked Channels 0x64 32 read-write n 0x0 0x0 COMBINE0 Combine Channels For n = 0 0 1 read-write 0 Channels (n) and (n+1) are independent. #0 1 Channels (n) and (n+1) are combined. #1 COMBINE1 Combine Channels For n = 2 8 1 read-write 0 Channels (n) and (n+1) are independent. #0 1 Channels (n) and (n+1) are combined. #1 COMBINE2 Combine Channels For n = 4 16 1 read-write 0 Channels (n) and (n+1) are independent. #0 1 Channels (n) and (n+1) are combined. #1 COMBINE3 Combine Channels For n = 6 24 1 read-write 0 Channels (n) and (n+1) are independent. #0 1 Channels (n) and (n+1) are combined. #1 COMP0 Complement Of Channel (n) For n = 0 1 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 COMP1 Complement Of Channel (n) For n = 2 9 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 COMP2 Complement Of Channel (n) For n = 4 17 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 COMP3 Complement Of Channel (n) for n = 6 25 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 DECAP0 Dual Edge Capture Mode Captures For n = 0 3 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DECAP1 Dual Edge Capture Mode Captures For n = 2 11 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DECAP2 Dual Edge Capture Mode Captures For n = 4 19 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DECAP3 Dual Edge Capture Mode Captures For n = 6 27 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DECAPEN0 Dual Edge Capture Mode Enable For n = 0 2 1 read-write 0 The Dual Edge Capture mode in this pair of channels is disabled. #0 1 The Dual Edge Capture mode in this pair of channels is enabled. #1 DECAPEN1 Dual Edge Capture Mode Enable For n = 2 10 1 read-write 0 The Dual Edge Capture mode in this pair of channels is disabled. #0 1 The Dual Edge Capture mode in this pair of channels is enabled. #1 DECAPEN2 Dual Edge Capture Mode Enable For n = 4 18 1 read-write 0 The Dual Edge Capture mode in this pair of channels is disabled. #0 1 The Dual Edge Capture mode in this pair of channels is enabled. #1 DECAPEN3 Dual Edge Capture Mode Enable For n = 6 26 1 read-write 0 The Dual Edge Capture mode in this pair of channels is disabled. #0 1 The Dual Edge Capture mode in this pair of channels is enabled. #1 DTEN0 Deadtime Enable For n = 0 4 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 DTEN1 Deadtime Enable For n = 2 12 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 DTEN2 Deadtime Enable For n = 4 20 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 DTEN3 Deadtime Enable For n = 6 28 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 FAULTEN0 Fault Control Enable For n = 0 6 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 FAULTEN1 Fault Control Enable For n = 2 14 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 FAULTEN2 Fault Control Enable For n = 4 22 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 FAULTEN3 Fault Control Enable For n = 6 30 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 SYNCEN0 Synchronization Enable For n = 0 5 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 SYNCEN1 Synchronization Enable For n = 2 13 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 SYNCEN2 Synchronization Enable For n = 4 21 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 SYNCEN3 Synchronization Enable For n = 6 29 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 CONF Configuration 0x84 32 read-write n 0x0 0x0 BDMMODE BDM Mode 6 2 read-write GTBEEN Global Time Base Enable 9 1 read-write 0 Use of an external global time base is disabled. #0 1 Use of an external global time base is enabled. #1 GTBEOUT Global Time Base Output 10 1 read-write 0 A global time base signal generation is disabled. #0 1 A global time base signal generation is enabled. #1 NUMTOF TOF Frequency 0 5 read-write DEADTIME Deadtime Insertion Control 0x68 32 read-write n 0x0 0x0 DTPS Deadtime Prescaler Value 6 2 read-write 10 Divide the system clock by 4. #10 11 Divide the system clock by 16. #11 DTVAL Deadtime Value 0 6 read-write EXTTRIG FTM External Trigger 0x6C 32 read-write n 0x0 0x0 CH0TRIG Channel 0 Trigger Enable 4 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH1TRIG Channel 1 Trigger Enable 5 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH2TRIG Channel 2 Trigger Enable 0 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH3TRIG Channel 3 Trigger Enable 1 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH4TRIG Channel 4 Trigger Enable 2 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH5TRIG Channel 5 Trigger Enable 3 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 INITTRIGEN Initialization Trigger Enable 6 1 read-write 0 The generation of initialization trigger is disabled. #0 1 The generation of initialization trigger is enabled. #1 TRIGF Channel Trigger Flag 7 1 read-write 0 No channel trigger was generated. #0 1 A channel trigger was generated. #1 FILTER Input Capture Filter Control 0x78 32 read-write n 0x0 0x0 CH0FVAL Channel 0 Input Filter 0 4 read-write CH1FVAL Channel 1 Input Filter 4 4 read-write CH2FVAL Channel 2 Input Filter 8 4 read-write CH3FVAL Channel 3 Input Filter 12 4 read-write FLTCTRL Fault Control 0x7C 32 read-write n 0x0 0x0 FAULT0EN Fault Input 0 Enable 0 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT1EN Fault Input 1 Enable 1 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT2EN Fault Input 2 Enable 2 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT3EN Fault Input 3 Enable 3 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FFLTR0EN Fault Input 0 Filter Enable 4 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR1EN Fault Input 1 Filter Enable 5 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR2EN Fault Input 2 Filter Enable 6 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR3EN Fault Input 3 Filter Enable 7 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFVAL Fault Input Filter 8 4 read-write FLTPOL FTM Fault Input Polarity 0x88 32 read-write n 0x0 0x0 FLT0POL Fault Input 0 Polarity 0 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT1POL Fault Input 1 Polarity 1 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT2POL Fault Input 2 Polarity 2 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT3POL Fault Input 3 Polarity 3 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FMS Fault Mode Status 0x74 32 read-write n 0x0 0x0 FAULTF Fault Detection Flag 7 1 read-write 0 No fault condition was detected. #0 1 A fault condition was detected. #1 FAULTF0 Fault Detection Flag 0 0 1 read-write 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF1 Fault Detection Flag 1 1 1 read-write 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF2 Fault Detection Flag 2 2 1 read-write 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF3 Fault Detection Flag 3 3 1 read-write 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTIN Fault Inputs 5 1 read-only 0 The logic OR of the enabled fault inputs is 0. #0 1 The logic OR of the enabled fault inputs is 1. #1 WPEN Write Protection Enable 6 1 read-write 0 Write protection is disabled. Write protected bits can be written. #0 1 Write protection is enabled. Write protected bits cannot be written. #1 INVCTRL FTM Inverting Control 0x90 32 read-write n 0x0 0x0 INV0EN Pair Channels 0 Inverting Enable 0 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV1EN Pair Channels 1 Inverting Enable 1 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV2EN Pair Channels 2 Inverting Enable 2 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV3EN Pair Channels 3 Inverting Enable 3 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 MOD Modulo 0x8 32 read-write n 0x0 0x0 MOD Modulo Value 0 16 read-write MODE Features Mode Selection 0x54 32 read-write n 0x0 0x0 CAPTEST Capture Test Mode Enable 4 1 read-write 0 Capture test mode is disabled. #0 1 Capture test mode is enabled. #1 FAULTIE Fault Interrupt Enable 7 1 read-write 0 Fault control interrupt is disabled. #0 1 Fault control interrupt is enabled. #1 FAULTM Fault Control Mode 5 2 read-write 00 Fault control is disabled for all channels. #00 01 Fault control is enabled for even channels only (channels 0, 2, 4, and 6), and the selected mode is the manual fault clearing. #01 10 Fault control is enabled for all channels, and the selected mode is the manual fault clearing. #10 11 Fault control is enabled for all channels, and the selected mode is the automatic fault clearing. #11 FTMEN FTM Enable 0 1 read-write 0 Only the TPM-compatible registers (first set of registers) can be used without any restriction. Do not use the FTM-specific registers. #0 1 All registers including the FTM-specific registers (second set of registers) are available for use with no restrictions. #1 INIT Initialize The Channels Output 1 1 read-write PWMSYNC PWM Synchronization Mode 3 1 read-write 0 No restrictions. Software and hardware triggers can be used by MOD, CnV, OUTMASK, and FTM counter synchronization. #0 1 Software trigger can only be used by MOD and CnV synchronization, and hardware triggers can only be used by OUTMASK and FTM counter synchronization. #1 WPDIS Write Protection Disable 2 1 read-write 0 Write protection is enabled. #0 1 Write protection is disabled. #1 OUTINIT Initial State For Channels Output 0x5C 32 read-write n 0x0 0x0 CH0OI Channel 0 Output Initialization Value 0 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH1OI Channel 1 Output Initialization Value 1 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH2OI Channel 2 Output Initialization Value 2 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH3OI Channel 3 Output Initialization Value 3 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH4OI Channel 4 Output Initialization Value 4 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH5OI Channel 5 Output Initialization Value 5 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH6OI Channel 6 Output Initialization Value 6 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH7OI Channel 7 Output Initialization Value 7 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 OUTMASK Output Mask 0x60 32 read-write n 0x0 0x0 CH0OM Channel 0 Output Mask 0 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH1OM Channel 1 Output Mask 1 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH2OM Channel 2 Output Mask 2 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH3OM Channel 3 Output Mask 3 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH4OM Channel 4 Output Mask 4 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH5OM Channel 5 Output Mask 5 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH6OM Channel 6 Output Mask 6 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH7OM Channel 7 Output Mask 7 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 POL Channels Polarity 0x70 32 read-write n 0x0 0x0 POL0 Channel 0 Polarity 0 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL1 Channel 1 Polarity 1 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL2 Channel 2 Polarity 2 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL3 Channel 3 Polarity 3 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL4 Channel 4 Polarity 4 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL5 Channel 5 Polarity 5 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL6 Channel 6 Polarity 6 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL7 Channel 7 Polarity 7 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 PWMLOAD FTM PWM Load 0x98 32 read-write n 0x0 0x0 CH0SEL Channel 0 Select 0 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH1SEL Channel 1 Select 1 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH2SEL Channel 2 Select 2 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH3SEL Channel 3 Select 3 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH4SEL Channel 4 Select 4 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH5SEL Channel 5 Select 5 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH6SEL Channel 6 Select 6 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH7SEL Channel 7 Select 7 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 LDOK Load Enable 9 1 read-write 0 Loading updated values is disabled. #0 1 Loading updated values is enabled. #1 QDCTRL Quadrature Decoder Control And Status 0x80 32 read-write n 0x0 0x0 PHAFLTREN Phase A Input Filter Enable 7 1 read-write 0 Phase A input filter is disabled. #0 1 Phase A input filter is enabled. #1 PHAPOL Phase A Input Polarity 5 1 read-write 0 Normal polarity. Phase A input signal is not inverted before identifying the rising and falling edges of this signal. #0 1 Inverted polarity. Phase A input signal is inverted before identifying the rising and falling edges of this signal. #1 PHBFLTREN Phase B Input Filter Enable 6 1 read-write 0 Phase B input filter is disabled. #0 1 Phase B input filter is enabled. #1 PHBPOL Phase B Input Polarity 4 1 read-write 0 Normal polarity. Phase B input signal is not inverted before identifying the rising and falling edges of this signal. #0 1 Inverted polarity. Phase B input signal is inverted before identifying the rising and falling edges of this signal. #1 QUADEN Quadrature Decoder Mode Enable 0 1 read-write 0 Quadrature Decoder mode is disabled. #0 1 Quadrature Decoder mode is enabled. #1 QUADIR FTM Counter Direction In Quadrature Decoder Mode 2 1 read-only 0 Counting direction is decreasing (FTM counter decrement). #0 1 Counting direction is increasing (FTM counter increment). #1 QUADMODE Quadrature Decoder Mode 3 1 read-write 0 Phase A and phase B encoding mode. #0 1 Count and direction encoding mode. #1 TOFDIR Timer Overflow Direction In Quadrature Decoder Mode 1 1 read-only 0 TOF bit was set on the bottom of counting. There was an FTM counter decrement and FTM counter changes from its minimum value (CNTIN register) to its maximum value (MOD register). #0 1 TOF bit was set on the top of counting. There was an FTM counter increment and FTM counter changes from its maximum value (MOD register) to its minimum value (CNTIN register). #1 SC Status And Control 0x0 32 read-write n 0x0 0x0 CLKS Clock Source Selection 3 2 read-write 00 No clock selected. This in effect disables the FTM counter. #00 01 System clock #01 10 Fixed frequency clock #10 11 External clock #11 CPWMS Center-Aligned PWM Select 5 1 read-write 0 FTM counter operates in Up Counting mode. #0 1 FTM counter operates in Up-Down Counting mode. #1 PS Prescale Factor Selection 0 3 read-write 000 Divide by 1 #000 001 Divide by 2 #001 010 Divide by 4 #010 011 Divide by 8 #011 100 Divide by 16 #100 101 Divide by 32 #101 110 Divide by 64 #110 111 Divide by 128 #111 TOF Timer Overflow Flag 7 1 read-write 0 FTM counter has not overflowed. #0 1 FTM counter has overflowed. #1 TOIE Timer Overflow Interrupt Enable 6 1 read-write 0 Disable TOF interrupts. Use software polling. #0 1 Enable TOF interrupts. An interrupt is generated when TOF equals one. #1 STATUS Capture And Compare Status 0x50 32 read-write n 0x0 0x0 CH0F Channel 0 Flag 0 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH1F Channel 1 Flag 1 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH2F Channel 2 Flag 2 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH3F Channel 3 Flag 3 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH4F Channel 4 Flag 4 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH5F Channel 5 Flag 5 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH6F Channel 6 Flag 6 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH7F Channel 7 Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 SWOCTRL FTM Software Output Control 0x94 32 read-write n 0x0 0x0 CH0OC Channel 0 Software Output Control Enable 0 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH0OCV Channel 0 Software Output Control Value 8 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH1OC Channel 1 Software Output Control Enable 1 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH1OCV Channel 1 Software Output Control Value 9 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH2OC Channel 2 Software Output Control Enable 2 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH2OCV Channel 2 Software Output Control Value 10 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH3OC Channel 3 Software Output Control Enable 3 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH3OCV Channel 3 Software Output Control Value 11 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH4OC Channel 4 Software Output Control Enable 4 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH4OCV Channel 4 Software Output Control Value 12 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH5OC Channel 5 Software Output Control Enable 5 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH5OCV Channel 5 Software Output Control Value 13 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH6OC Channel 6 Software Output Control Enable 6 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH6OCV Channel 6 Software Output Control Value 14 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH7OC Channel 7 Software Output Control Enable 7 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH7OCV Channel 7 Software Output Control Value 15 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 SYNC Synchronization 0x58 32 read-write n 0x0 0x0 CNTMAX Maximum Loading Point Enable 1 1 read-write 0 The maximum loading point is disabled. #0 1 The maximum loading point is enabled. #1 CNTMIN Minimum Loading Point Enable 0 1 read-write 0 The minimum loading point is disabled. #0 1 The minimum loading point is enabled. #1 REINIT FTM Counter Reinitialization By Synchronization (FTM counter synchronization) 2 1 read-write 0 FTM counter continues to count normally. #0 1 FTM counter is updated with its initial value when the selected trigger is detected. #1 SWSYNC PWM Synchronization Software Trigger 7 1 read-write 0 Software trigger is not selected. #0 1 Software trigger is selected. #1 SYNCHOM Output Mask Synchronization 3 1 read-write 0 OUTMASK register is updated with the value of its buffer in all rising edges of the system clock. #0 1 OUTMASK register is updated with the value of its buffer only by the PWM synchronization. #1 TRIG0 PWM Synchronization Hardware Trigger 0 4 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 TRIG1 PWM Synchronization Hardware Trigger 1 5 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 TRIG2 PWM Synchronization Hardware Trigger 2 6 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 SYNCONF Synchronization Configuration 0x8C 32 read-write n 0x0 0x0 CNTINC CNTIN Register Synchronization 2 1 read-write 0 CNTIN register is updated with its buffer value at all rising edges of system clock. #0 1 CNTIN register is updated with its buffer value by the PWM synchronization. #1 HWINVC Inverting control synchronization is activated by a hardware trigger. 19 1 read-write 0 A hardware trigger does not activate the INVCTRL register synchronization. #0 1 A hardware trigger activates the INVCTRL register synchronization. #1 HWOM Output mask synchronization is activated by a hardware trigger. 18 1 read-write 0 A hardware trigger does not activate the OUTMASK register synchronization. #0 1 A hardware trigger activates the OUTMASK register synchronization. #1 HWRSTCNT FTM counter synchronization is activated by a hardware trigger. 16 1 read-write 0 A hardware trigger does not activate the FTM counter synchronization. #0 1 A hardware trigger activates the FTM counter synchronization. #1 HWSOC Software output control synchronization is activated by a hardware trigger. 20 1 read-write 0 A hardware trigger does not activate the SWOCTRL register synchronization. #0 1 A hardware trigger activates the SWOCTRL register synchronization. #1 HWTRIGMODE Hardware Trigger Mode 0 1 read-write 0 FTM clears the TRIGj bit when the hardware trigger j is detected, where j = 0, 1,2. #0 1 FTM does not clear the TRIGj bit when the hardware trigger j is detected, where j = 0, 1,2. #1 HWWRBUF MOD, CNTIN, and CV registers synchronization is activated by a hardware trigger. 17 1 read-write 0 A hardware trigger does not activate MOD, CNTIN, and CV registers synchronization. #0 1 A hardware trigger activates MOD, CNTIN, and CV registers synchronization. #1 INVC INVCTRL Register Synchronization 4 1 read-write 0 INVCTRL register is updated with its buffer value at all rising edges of system clock. #0 1 INVCTRL register is updated with its buffer value by the PWM synchronization. #1 SWINVC Inverting control synchronization is activated by the software trigger. 11 1 read-write 0 The software trigger does not activate the INVCTRL register synchronization. #0 1 The software trigger activates the INVCTRL register synchronization. #1 SWOC SWOCTRL Register Synchronization 5 1 read-write 0 SWOCTRL register is updated with its buffer value at all rising edges of system clock. #0 1 SWOCTRL register is updated with its buffer value by the PWM synchronization. #1 SWOM Output mask synchronization is activated by the software trigger. 10 1 read-write 0 The software trigger does not activate the OUTMASK register synchronization. #0 1 The software trigger activates the OUTMASK register synchronization. #1 SWRSTCNT FTM counter synchronization is activated by the software trigger. 8 1 read-write 0 The software trigger does not activate the FTM counter synchronization. #0 1 The software trigger activates the FTM counter synchronization. #1 SWSOC Software output control synchronization is activated by the software trigger. 12 1 read-write 0 The software trigger does not activate the SWOCTRL register synchronization. #0 1 The software trigger activates the SWOCTRL register synchronization. #1 SWWRBUF MOD, CNTIN, and CV registers synchronization is activated by the software trigger. 9 1 read-write 0 The software trigger does not activate MOD, CNTIN, and CV registers synchronization. #0 1 The software trigger activates MOD, CNTIN, and CV registers synchronization. #1 SYNCMODE Synchronization Mode 7 1 read-write 0 Legacy PWM synchronization is selected. #0 1 Enhanced PWM synchronization is selected. #1 FTM3 FlexTimer Module FTM 0x0 0x0 0x9C registers n FTM3 71 C0SC Channel (n) Status And Control 0x18 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C0V Channel (n) Value 0x20 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write C1SC Channel (n) Status And Control 0x2C 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C1V Channel (n) Value 0x38 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write C2SC Channel (n) Status And Control 0x48 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C2V Channel (n) Value 0x58 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write C3SC Channel (n) Status And Control 0x6C 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C3V Channel (n) Value 0x80 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write C4SC Channel (n) Status And Control 0x98 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C4V Channel (n) Value 0xB0 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write C5SC Channel (n) Status And Control 0xCC 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C5V Channel (n) Value 0xE8 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write C6SC Channel (n) Status And Control 0x108 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C6V Channel (n) Value 0x128 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write C7SC Channel (n) Status And Control 0x14C 32 read-write n 0x0 0x0 CHF Channel Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CHIE Channel Interrupt Enable 6 1 read-write 0 Disable channel interrupts. Use software polling. #0 1 Enable channel interrupts. #1 DMA DMA Enable 0 1 read-write 0 Disable DMA transfers. #0 1 Enable DMA transfers. #1 ELSA Edge or Level Select 2 1 read-write ELSB Edge or Level Select 3 1 read-write ICRST FTM counter reset by the selected input capture event. 1 1 read-write 0 FTM counter is not reset when the selected channel (n) input event is detected. #0 1 FTM counter is reset when the selected channel (n) input event is detected. #1 MSA Channel Mode Select 4 1 read-write MSB Channel Mode Select 5 1 read-write C7V Channel (n) Value 0x170 32 read-write n 0x0 0x0 VAL Channel Value 0 16 read-write CNT Counter 0x4 32 read-write n 0x0 0x0 COUNT Counter Value 0 16 read-write CNTIN Counter Initial Value 0x4C 32 read-write n 0x0 0x0 INIT Initial Value Of The FTM Counter 0 16 read-write COMBINE Function For Linked Channels 0x64 32 read-write n 0x0 0x0 COMBINE0 Combine Channels For n = 0 0 1 read-write 0 Channels (n) and (n+1) are independent. #0 1 Channels (n) and (n+1) are combined. #1 COMBINE1 Combine Channels For n = 2 8 1 read-write 0 Channels (n) and (n+1) are independent. #0 1 Channels (n) and (n+1) are combined. #1 COMBINE2 Combine Channels For n = 4 16 1 read-write 0 Channels (n) and (n+1) are independent. #0 1 Channels (n) and (n+1) are combined. #1 COMBINE3 Combine Channels For n = 6 24 1 read-write 0 Channels (n) and (n+1) are independent. #0 1 Channels (n) and (n+1) are combined. #1 COMP0 Complement Of Channel (n) For n = 0 1 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 COMP1 Complement Of Channel (n) For n = 2 9 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 COMP2 Complement Of Channel (n) For n = 4 17 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 COMP3 Complement Of Channel (n) for n = 6 25 1 read-write 0 The channel (n+1) output is the same as the channel (n) output. #0 1 The channel (n+1) output is the complement of the channel (n) output. #1 DECAP0 Dual Edge Capture Mode Captures For n = 0 3 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DECAP1 Dual Edge Capture Mode Captures For n = 2 11 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DECAP2 Dual Edge Capture Mode Captures For n = 4 19 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DECAP3 Dual Edge Capture Mode Captures For n = 6 27 1 read-write 0 The dual edge captures are inactive. #0 1 The dual edge captures are active. #1 DECAPEN0 Dual Edge Capture Mode Enable For n = 0 2 1 read-write 0 The Dual Edge Capture mode in this pair of channels is disabled. #0 1 The Dual Edge Capture mode in this pair of channels is enabled. #1 DECAPEN1 Dual Edge Capture Mode Enable For n = 2 10 1 read-write 0 The Dual Edge Capture mode in this pair of channels is disabled. #0 1 The Dual Edge Capture mode in this pair of channels is enabled. #1 DECAPEN2 Dual Edge Capture Mode Enable For n = 4 18 1 read-write 0 The Dual Edge Capture mode in this pair of channels is disabled. #0 1 The Dual Edge Capture mode in this pair of channels is enabled. #1 DECAPEN3 Dual Edge Capture Mode Enable For n = 6 26 1 read-write 0 The Dual Edge Capture mode in this pair of channels is disabled. #0 1 The Dual Edge Capture mode in this pair of channels is enabled. #1 DTEN0 Deadtime Enable For n = 0 4 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 DTEN1 Deadtime Enable For n = 2 12 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 DTEN2 Deadtime Enable For n = 4 20 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 DTEN3 Deadtime Enable For n = 6 28 1 read-write 0 The deadtime insertion in this pair of channels is disabled. #0 1 The deadtime insertion in this pair of channels is enabled. #1 FAULTEN0 Fault Control Enable For n = 0 6 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 FAULTEN1 Fault Control Enable For n = 2 14 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 FAULTEN2 Fault Control Enable For n = 4 22 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 FAULTEN3 Fault Control Enable For n = 6 30 1 read-write 0 The fault control in this pair of channels is disabled. #0 1 The fault control in this pair of channels is enabled. #1 SYNCEN0 Synchronization Enable For n = 0 5 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 SYNCEN1 Synchronization Enable For n = 2 13 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 SYNCEN2 Synchronization Enable For n = 4 21 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 SYNCEN3 Synchronization Enable For n = 6 29 1 read-write 0 The PWM synchronization in this pair of channels is disabled. #0 1 The PWM synchronization in this pair of channels is enabled. #1 CONF Configuration 0x84 32 read-write n 0x0 0x0 BDMMODE BDM Mode 6 2 read-write GTBEEN Global Time Base Enable 9 1 read-write 0 Use of an external global time base is disabled. #0 1 Use of an external global time base is enabled. #1 GTBEOUT Global Time Base Output 10 1 read-write 0 A global time base signal generation is disabled. #0 1 A global time base signal generation is enabled. #1 NUMTOF TOF Frequency 0 5 read-write DEADTIME Deadtime Insertion Control 0x68 32 read-write n 0x0 0x0 DTPS Deadtime Prescaler Value 6 2 read-write 10 Divide the system clock by 4. #10 11 Divide the system clock by 16. #11 DTVAL Deadtime Value 0 6 read-write EXTTRIG FTM External Trigger 0x6C 32 read-write n 0x0 0x0 CH0TRIG Channel 0 Trigger Enable 4 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH1TRIG Channel 1 Trigger Enable 5 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH2TRIG Channel 2 Trigger Enable 0 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH3TRIG Channel 3 Trigger Enable 1 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH4TRIG Channel 4 Trigger Enable 2 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 CH5TRIG Channel 5 Trigger Enable 3 1 read-write 0 The generation of the channel trigger is disabled. #0 1 The generation of the channel trigger is enabled. #1 INITTRIGEN Initialization Trigger Enable 6 1 read-write 0 The generation of initialization trigger is disabled. #0 1 The generation of initialization trigger is enabled. #1 TRIGF Channel Trigger Flag 7 1 read-write 0 No channel trigger was generated. #0 1 A channel trigger was generated. #1 FILTER Input Capture Filter Control 0x78 32 read-write n 0x0 0x0 CH0FVAL Channel 0 Input Filter 0 4 read-write CH1FVAL Channel 1 Input Filter 4 4 read-write CH2FVAL Channel 2 Input Filter 8 4 read-write CH3FVAL Channel 3 Input Filter 12 4 read-write FLTCTRL Fault Control 0x7C 32 read-write n 0x0 0x0 FAULT0EN Fault Input 0 Enable 0 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT1EN Fault Input 1 Enable 1 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT2EN Fault Input 2 Enable 2 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FAULT3EN Fault Input 3 Enable 3 1 read-write 0 Fault input is disabled. #0 1 Fault input is enabled. #1 FFLTR0EN Fault Input 0 Filter Enable 4 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR1EN Fault Input 1 Filter Enable 5 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR2EN Fault Input 2 Filter Enable 6 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFLTR3EN Fault Input 3 Filter Enable 7 1 read-write 0 Fault input filter is disabled. #0 1 Fault input filter is enabled. #1 FFVAL Fault Input Filter 8 4 read-write FLTPOL FTM Fault Input Polarity 0x88 32 read-write n 0x0 0x0 FLT0POL Fault Input 0 Polarity 0 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT1POL Fault Input 1 Polarity 1 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT2POL Fault Input 2 Polarity 2 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FLT3POL Fault Input 3 Polarity 3 1 read-write 0 The fault input polarity is active high. A 1 at the fault input indicates a fault. #0 1 The fault input polarity is active low. A 0 at the fault input indicates a fault. #1 FMS Fault Mode Status 0x74 32 read-write n 0x0 0x0 FAULTF Fault Detection Flag 7 1 read-write 0 No fault condition was detected. #0 1 A fault condition was detected. #1 FAULTF0 Fault Detection Flag 0 0 1 read-write 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF1 Fault Detection Flag 1 1 1 read-write 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF2 Fault Detection Flag 2 2 1 read-write 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTF3 Fault Detection Flag 3 3 1 read-write 0 No fault condition was detected at the fault input. #0 1 A fault condition was detected at the fault input. #1 FAULTIN Fault Inputs 5 1 read-only 0 The logic OR of the enabled fault inputs is 0. #0 1 The logic OR of the enabled fault inputs is 1. #1 WPEN Write Protection Enable 6 1 read-write 0 Write protection is disabled. Write protected bits can be written. #0 1 Write protection is enabled. Write protected bits cannot be written. #1 INVCTRL FTM Inverting Control 0x90 32 read-write n 0x0 0x0 INV0EN Pair Channels 0 Inverting Enable 0 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV1EN Pair Channels 1 Inverting Enable 1 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV2EN Pair Channels 2 Inverting Enable 2 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 INV3EN Pair Channels 3 Inverting Enable 3 1 read-write 0 Inverting is disabled. #0 1 Inverting is enabled. #1 MOD Modulo 0x8 32 read-write n 0x0 0x0 MOD Modulo Value 0 16 read-write MODE Features Mode Selection 0x54 32 read-write n 0x0 0x0 CAPTEST Capture Test Mode Enable 4 1 read-write 0 Capture test mode is disabled. #0 1 Capture test mode is enabled. #1 FAULTIE Fault Interrupt Enable 7 1 read-write 0 Fault control interrupt is disabled. #0 1 Fault control interrupt is enabled. #1 FAULTM Fault Control Mode 5 2 read-write 00 Fault control is disabled for all channels. #00 01 Fault control is enabled for even channels only (channels 0, 2, 4, and 6), and the selected mode is the manual fault clearing. #01 10 Fault control is enabled for all channels, and the selected mode is the manual fault clearing. #10 11 Fault control is enabled for all channels, and the selected mode is the automatic fault clearing. #11 FTMEN FTM Enable 0 1 read-write 0 Only the TPM-compatible registers (first set of registers) can be used without any restriction. Do not use the FTM-specific registers. #0 1 All registers including the FTM-specific registers (second set of registers) are available for use with no restrictions. #1 INIT Initialize The Channels Output 1 1 read-write PWMSYNC PWM Synchronization Mode 3 1 read-write 0 No restrictions. Software and hardware triggers can be used by MOD, CnV, OUTMASK, and FTM counter synchronization. #0 1 Software trigger can only be used by MOD and CnV synchronization, and hardware triggers can only be used by OUTMASK and FTM counter synchronization. #1 WPDIS Write Protection Disable 2 1 read-write 0 Write protection is enabled. #0 1 Write protection is disabled. #1 OUTINIT Initial State For Channels Output 0x5C 32 read-write n 0x0 0x0 CH0OI Channel 0 Output Initialization Value 0 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH1OI Channel 1 Output Initialization Value 1 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH2OI Channel 2 Output Initialization Value 2 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH3OI Channel 3 Output Initialization Value 3 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH4OI Channel 4 Output Initialization Value 4 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH5OI Channel 5 Output Initialization Value 5 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH6OI Channel 6 Output Initialization Value 6 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 CH7OI Channel 7 Output Initialization Value 7 1 read-write 0 The initialization value is 0. #0 1 The initialization value is 1. #1 OUTMASK Output Mask 0x60 32 read-write n 0x0 0x0 CH0OM Channel 0 Output Mask 0 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH1OM Channel 1 Output Mask 1 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH2OM Channel 2 Output Mask 2 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH3OM Channel 3 Output Mask 3 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH4OM Channel 4 Output Mask 4 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH5OM Channel 5 Output Mask 5 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH6OM Channel 6 Output Mask 6 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 CH7OM Channel 7 Output Mask 7 1 read-write 0 Channel output is not masked. It continues to operate normally. #0 1 Channel output is masked. It is forced to its inactive state. #1 POL Channels Polarity 0x70 32 read-write n 0x0 0x0 POL0 Channel 0 Polarity 0 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL1 Channel 1 Polarity 1 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL2 Channel 2 Polarity 2 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL3 Channel 3 Polarity 3 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL4 Channel 4 Polarity 4 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL5 Channel 5 Polarity 5 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL6 Channel 6 Polarity 6 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 POL7 Channel 7 Polarity 7 1 read-write 0 The channel polarity is active high. #0 1 The channel polarity is active low. #1 PWMLOAD FTM PWM Load 0x98 32 read-write n 0x0 0x0 CH0SEL Channel 0 Select 0 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH1SEL Channel 1 Select 1 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH2SEL Channel 2 Select 2 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH3SEL Channel 3 Select 3 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH4SEL Channel 4 Select 4 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH5SEL Channel 5 Select 5 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH6SEL Channel 6 Select 6 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 CH7SEL Channel 7 Select 7 1 read-write 0 Do not include the channel in the matching process. #0 1 Include the channel in the matching process. #1 LDOK Load Enable 9 1 read-write 0 Loading updated values is disabled. #0 1 Loading updated values is enabled. #1 QDCTRL Quadrature Decoder Control And Status 0x80 32 read-write n 0x0 0x0 PHAFLTREN Phase A Input Filter Enable 7 1 read-write 0 Phase A input filter is disabled. #0 1 Phase A input filter is enabled. #1 PHAPOL Phase A Input Polarity 5 1 read-write 0 Normal polarity. Phase A input signal is not inverted before identifying the rising and falling edges of this signal. #0 1 Inverted polarity. Phase A input signal is inverted before identifying the rising and falling edges of this signal. #1 PHBFLTREN Phase B Input Filter Enable 6 1 read-write 0 Phase B input filter is disabled. #0 1 Phase B input filter is enabled. #1 PHBPOL Phase B Input Polarity 4 1 read-write 0 Normal polarity. Phase B input signal is not inverted before identifying the rising and falling edges of this signal. #0 1 Inverted polarity. Phase B input signal is inverted before identifying the rising and falling edges of this signal. #1 QUADEN Quadrature Decoder Mode Enable 0 1 read-write 0 Quadrature Decoder mode is disabled. #0 1 Quadrature Decoder mode is enabled. #1 QUADIR FTM Counter Direction In Quadrature Decoder Mode 2 1 read-only 0 Counting direction is decreasing (FTM counter decrement). #0 1 Counting direction is increasing (FTM counter increment). #1 QUADMODE Quadrature Decoder Mode 3 1 read-write 0 Phase A and phase B encoding mode. #0 1 Count and direction encoding mode. #1 TOFDIR Timer Overflow Direction In Quadrature Decoder Mode 1 1 read-only 0 TOF bit was set on the bottom of counting. There was an FTM counter decrement and FTM counter changes from its minimum value (CNTIN register) to its maximum value (MOD register). #0 1 TOF bit was set on the top of counting. There was an FTM counter increment and FTM counter changes from its maximum value (MOD register) to its minimum value (CNTIN register). #1 SC Status And Control 0x0 32 read-write n 0x0 0x0 CLKS Clock Source Selection 3 2 read-write 00 No clock selected. This in effect disables the FTM counter. #00 01 System clock #01 10 Fixed frequency clock #10 11 External clock #11 CPWMS Center-Aligned PWM Select 5 1 read-write 0 FTM counter operates in Up Counting mode. #0 1 FTM counter operates in Up-Down Counting mode. #1 PS Prescale Factor Selection 0 3 read-write 000 Divide by 1 #000 001 Divide by 2 #001 010 Divide by 4 #010 011 Divide by 8 #011 100 Divide by 16 #100 101 Divide by 32 #101 110 Divide by 64 #110 111 Divide by 128 #111 TOF Timer Overflow Flag 7 1 read-write 0 FTM counter has not overflowed. #0 1 FTM counter has overflowed. #1 TOIE Timer Overflow Interrupt Enable 6 1 read-write 0 Disable TOF interrupts. Use software polling. #0 1 Enable TOF interrupts. An interrupt is generated when TOF equals one. #1 STATUS Capture And Compare Status 0x50 32 read-write n 0x0 0x0 CH0F Channel 0 Flag 0 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH1F Channel 1 Flag 1 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH2F Channel 2 Flag 2 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH3F Channel 3 Flag 3 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH4F Channel 4 Flag 4 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH5F Channel 5 Flag 5 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH6F Channel 6 Flag 6 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 CH7F Channel 7 Flag 7 1 read-write 0 No channel event has occurred. #0 1 A channel event has occurred. #1 SWOCTRL FTM Software Output Control 0x94 32 read-write n 0x0 0x0 CH0OC Channel 0 Software Output Control Enable 0 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH0OCV Channel 0 Software Output Control Value 8 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH1OC Channel 1 Software Output Control Enable 1 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH1OCV Channel 1 Software Output Control Value 9 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH2OC Channel 2 Software Output Control Enable 2 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH2OCV Channel 2 Software Output Control Value 10 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH3OC Channel 3 Software Output Control Enable 3 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH3OCV Channel 3 Software Output Control Value 11 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH4OC Channel 4 Software Output Control Enable 4 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH4OCV Channel 4 Software Output Control Value 12 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH5OC Channel 5 Software Output Control Enable 5 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH5OCV Channel 5 Software Output Control Value 13 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH6OC Channel 6 Software Output Control Enable 6 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH6OCV Channel 6 Software Output Control Value 14 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 CH7OC Channel 7 Software Output Control Enable 7 1 read-write 0 The channel output is not affected by software output control. #0 1 The channel output is affected by software output control. #1 CH7OCV Channel 7 Software Output Control Value 15 1 read-write 0 The software output control forces 0 to the channel output. #0 1 The software output control forces 1 to the channel output. #1 SYNC Synchronization 0x58 32 read-write n 0x0 0x0 CNTMAX Maximum Loading Point Enable 1 1 read-write 0 The maximum loading point is disabled. #0 1 The maximum loading point is enabled. #1 CNTMIN Minimum Loading Point Enable 0 1 read-write 0 The minimum loading point is disabled. #0 1 The minimum loading point is enabled. #1 REINIT FTM Counter Reinitialization By Synchronization (FTM counter synchronization) 2 1 read-write 0 FTM counter continues to count normally. #0 1 FTM counter is updated with its initial value when the selected trigger is detected. #1 SWSYNC PWM Synchronization Software Trigger 7 1 read-write 0 Software trigger is not selected. #0 1 Software trigger is selected. #1 SYNCHOM Output Mask Synchronization 3 1 read-write 0 OUTMASK register is updated with the value of its buffer in all rising edges of the system clock. #0 1 OUTMASK register is updated with the value of its buffer only by the PWM synchronization. #1 TRIG0 PWM Synchronization Hardware Trigger 0 4 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 TRIG1 PWM Synchronization Hardware Trigger 1 5 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 TRIG2 PWM Synchronization Hardware Trigger 2 6 1 read-write 0 Trigger is disabled. #0 1 Trigger is enabled. #1 SYNCONF Synchronization Configuration 0x8C 32 read-write n 0x0 0x0 CNTINC CNTIN Register Synchronization 2 1 read-write 0 CNTIN register is updated with its buffer value at all rising edges of system clock. #0 1 CNTIN register is updated with its buffer value by the PWM synchronization. #1 HWINVC Inverting control synchronization is activated by a hardware trigger. 19 1 read-write 0 A hardware trigger does not activate the INVCTRL register synchronization. #0 1 A hardware trigger activates the INVCTRL register synchronization. #1 HWOM Output mask synchronization is activated by a hardware trigger. 18 1 read-write 0 A hardware trigger does not activate the OUTMASK register synchronization. #0 1 A hardware trigger activates the OUTMASK register synchronization. #1 HWRSTCNT FTM counter synchronization is activated by a hardware trigger. 16 1 read-write 0 A hardware trigger does not activate the FTM counter synchronization. #0 1 A hardware trigger activates the FTM counter synchronization. #1 HWSOC Software output control synchronization is activated by a hardware trigger. 20 1 read-write 0 A hardware trigger does not activate the SWOCTRL register synchronization. #0 1 A hardware trigger activates the SWOCTRL register synchronization. #1 HWTRIGMODE Hardware Trigger Mode 0 1 read-write 0 FTM clears the TRIGj bit when the hardware trigger j is detected, where j = 0, 1,2. #0 1 FTM does not clear the TRIGj bit when the hardware trigger j is detected, where j = 0, 1,2. #1 HWWRBUF MOD, CNTIN, and CV registers synchronization is activated by a hardware trigger. 17 1 read-write 0 A hardware trigger does not activate MOD, CNTIN, and CV registers synchronization. #0 1 A hardware trigger activates MOD, CNTIN, and CV registers synchronization. #1 INVC INVCTRL Register Synchronization 4 1 read-write 0 INVCTRL register is updated with its buffer value at all rising edges of system clock. #0 1 INVCTRL register is updated with its buffer value by the PWM synchronization. #1 SWINVC Inverting control synchronization is activated by the software trigger. 11 1 read-write 0 The software trigger does not activate the INVCTRL register synchronization. #0 1 The software trigger activates the INVCTRL register synchronization. #1 SWOC SWOCTRL Register Synchronization 5 1 read-write 0 SWOCTRL register is updated with its buffer value at all rising edges of system clock. #0 1 SWOCTRL register is updated with its buffer value by the PWM synchronization. #1 SWOM Output mask synchronization is activated by the software trigger. 10 1 read-write 0 The software trigger does not activate the OUTMASK register synchronization. #0 1 The software trigger activates the OUTMASK register synchronization. #1 SWRSTCNT FTM counter synchronization is activated by the software trigger. 8 1 read-write 0 The software trigger does not activate the FTM counter synchronization. #0 1 The software trigger activates the FTM counter synchronization. #1 SWSOC Software output control synchronization is activated by the software trigger. 12 1 read-write 0 The software trigger does not activate the SWOCTRL register synchronization. #0 1 The software trigger activates the SWOCTRL register synchronization. #1 SWWRBUF MOD, CNTIN, and CV registers synchronization is activated by the software trigger. 9 1 read-write 0 The software trigger does not activate MOD, CNTIN, and CV registers synchronization. #0 1 The software trigger activates MOD, CNTIN, and CV registers synchronization. #1 SYNCMODE Synchronization Mode 7 1 read-write 0 Legacy PWM synchronization is selected. #0 1 Enhanced PWM synchronization is selected. #1 GPIOA General Purpose Input/Output GPIO 0x0 0x0 0x18 registers n PORTA 59 PCOR Port Clear Output Register 0x8 32 write-only n 0x0 0x0 PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO0 Port Clear Output 0 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO1 Port Clear Output 1 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO10 Port Clear Output 10 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO11 Port Clear Output 11 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO12 Port Clear Output 12 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO13 Port Clear Output 13 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO14 Port Clear Output 14 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO15 Port Clear Output 15 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO16 Port Clear Output 16 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO17 Port Clear Output 17 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO18 Port Clear Output 18 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO19 Port Clear Output 19 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO2 Port Clear Output 2 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO20 Port Clear Output 20 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO21 Port Clear Output 21 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO22 Port Clear Output 22 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO23 Port Clear Output 23 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO24 Port Clear Output 24 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO25 Port Clear Output 25 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO26 Port Clear Output 26 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO27 Port Clear Output 27 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO28 Port Clear Output 28 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO29 Port Clear Output 29 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO3 Port Clear Output 3 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO30 Port Clear Output 30 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO31 Port Clear Output 31 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO4 Port Clear Output 4 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO5 Port Clear Output 5 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO6 Port Clear Output 6 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO7 Port Clear Output 7 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO8 Port Clear Output 8 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO9 Port Clear Output 9 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PDDR Port Data Direction Register 0x14 32 read-write n 0x0 0x0 PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD0 Port Data Direction 0 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD1 Port Data Direction 1 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD10 Port Data Direction 10 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD11 Port Data Direction 11 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD12 Port Data Direction 12 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD13 Port Data Direction 13 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD14 Port Data Direction 14 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD15 Port Data Direction 15 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD16 Port Data Direction 16 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD17 Port Data Direction 17 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD18 Port Data Direction 18 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD19 Port Data Direction 19 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD2 Port Data Direction 2 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD20 Port Data Direction 20 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD21 Port Data Direction 21 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD22 Port Data Direction 22 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD23 Port Data Direction 23 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD24 Port Data Direction 24 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD25 Port Data Direction 25 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD26 Port Data Direction 26 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD27 Port Data Direction 27 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD28 Port Data Direction 28 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD29 Port Data Direction 29 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD3 Port Data Direction 3 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD30 Port Data Direction 30 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD31 Port Data Direction 31 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD4 Port Data Direction 4 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD5 Port Data Direction 5 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD6 Port Data Direction 6 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD7 Port Data Direction 7 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD8 Port Data Direction 8 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD9 Port Data Direction 9 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDIR Port Data Input Register 0x10 32 read-only n 0x0 0x0 PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI0 Port Data Input 0 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI1 Port Data Input 1 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI10 Port Data Input 10 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI11 Port Data Input 11 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI12 Port Data Input 12 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI13 Port Data Input 13 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI14 Port Data Input 14 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI15 Port Data Input 15 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI16 Port Data Input 16 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI17 Port Data Input 17 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI18 Port Data Input 18 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI19 Port Data Input 19 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI2 Port Data Input 2 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI20 Port Data Input 20 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI21 Port Data Input 21 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI22 Port Data Input 22 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI23 Port Data Input 23 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI24 Port Data Input 24 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI25 Port Data Input 25 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI26 Port Data Input 26 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI27 Port Data Input 27 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI28 Port Data Input 28 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI29 Port Data Input 29 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI3 Port Data Input 3 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI30 Port Data Input 30 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI31 Port Data Input 31 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI4 Port Data Input 4 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI5 Port Data Input 5 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI6 Port Data Input 6 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI7 Port Data Input 7 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI8 Port Data Input 8 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI9 Port Data Input 9 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDOR Port Data Output Register 0x0 32 read-write n 0x0 0x0 PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO0 Port Data Output 0 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO1 Port Data Output 1 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO10 Port Data Output 10 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO11 Port Data Output 11 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO12 Port Data Output 12 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO13 Port Data Output 13 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO14 Port Data Output 14 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO15 Port Data Output 15 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO16 Port Data Output 16 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO17 Port Data Output 17 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO18 Port Data Output 18 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO19 Port Data Output 19 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO2 Port Data Output 2 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO20 Port Data Output 20 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO21 Port Data Output 21 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO22 Port Data Output 22 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO23 Port Data Output 23 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO24 Port Data Output 24 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO25 Port Data Output 25 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO26 Port Data Output 26 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO27 Port Data Output 27 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO28 Port Data Output 28 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO29 Port Data Output 29 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO3 Port Data Output 3 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO30 Port Data Output 30 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO31 Port Data Output 31 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO4 Port Data Output 4 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO5 Port Data Output 5 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO6 Port Data Output 6 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO7 Port Data Output 7 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO8 Port Data Output 8 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO9 Port Data Output 9 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only n 0x0 0x0 PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO0 Port Set Output 0 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO1 Port Set Output 1 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO10 Port Set Output 10 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO11 Port Set Output 11 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO12 Port Set Output 12 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO13 Port Set Output 13 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO14 Port Set Output 14 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO15 Port Set Output 15 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO16 Port Set Output 16 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO17 Port Set Output 17 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO18 Port Set Output 18 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO19 Port Set Output 19 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO2 Port Set Output 2 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO20 Port Set Output 20 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO21 Port Set Output 21 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO22 Port Set Output 22 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO23 Port Set Output 23 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO24 Port Set Output 24 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO25 Port Set Output 25 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO26 Port Set Output 26 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO27 Port Set Output 27 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO28 Port Set Output 28 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO29 Port Set Output 29 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO3 Port Set Output 3 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO30 Port Set Output 30 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO31 Port Set Output 31 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO4 Port Set Output 4 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO5 Port Set Output 5 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO6 Port Set Output 6 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO7 Port Set Output 7 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO8 Port Set Output 8 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO9 Port Set Output 9 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTOR Port Toggle Output Register 0xC 32 write-only n 0x0 0x0 PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO0 Port Toggle Output 0 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO1 Port Toggle Output 1 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO10 Port Toggle Output 10 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO11 Port Toggle Output 11 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO12 Port Toggle Output 12 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO13 Port Toggle Output 13 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO14 Port Toggle Output 14 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO15 Port Toggle Output 15 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO16 Port Toggle Output 16 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO17 Port Toggle Output 17 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO18 Port Toggle Output 18 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO19 Port Toggle Output 19 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO2 Port Toggle Output 2 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO20 Port Toggle Output 20 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO21 Port Toggle Output 21 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO22 Port Toggle Output 22 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO23 Port Toggle Output 23 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO24 Port Toggle Output 24 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO25 Port Toggle Output 25 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO26 Port Toggle Output 26 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO27 Port Toggle Output 27 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO28 Port Toggle Output 28 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO29 Port Toggle Output 29 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO3 Port Toggle Output 3 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO30 Port Toggle Output 30 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO31 Port Toggle Output 31 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO4 Port Toggle Output 4 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO5 Port Toggle Output 5 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO6 Port Toggle Output 6 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO7 Port Toggle Output 7 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO8 Port Toggle Output 8 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO9 Port Toggle Output 9 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 GPIOB General Purpose Input/Output GPIO 0x0 0x0 0x18 registers n PORTB 60 PCOR Port Clear Output Register 0x8 32 write-only n 0x0 0x0 PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO0 Port Clear Output 0 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO1 Port Clear Output 1 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO10 Port Clear Output 10 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO11 Port Clear Output 11 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO12 Port Clear Output 12 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO13 Port Clear Output 13 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO14 Port Clear Output 14 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO15 Port Clear Output 15 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO16 Port Clear Output 16 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO17 Port Clear Output 17 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO18 Port Clear Output 18 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO19 Port Clear Output 19 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO2 Port Clear Output 2 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO20 Port Clear Output 20 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO21 Port Clear Output 21 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO22 Port Clear Output 22 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO23 Port Clear Output 23 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO24 Port Clear Output 24 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO25 Port Clear Output 25 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO26 Port Clear Output 26 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO27 Port Clear Output 27 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO28 Port Clear Output 28 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO29 Port Clear Output 29 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO3 Port Clear Output 3 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO30 Port Clear Output 30 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO31 Port Clear Output 31 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO4 Port Clear Output 4 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO5 Port Clear Output 5 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO6 Port Clear Output 6 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO7 Port Clear Output 7 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO8 Port Clear Output 8 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO9 Port Clear Output 9 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PDDR Port Data Direction Register 0x14 32 read-write n 0x0 0x0 PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD0 Port Data Direction 0 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD1 Port Data Direction 1 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD10 Port Data Direction 10 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD11 Port Data Direction 11 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD12 Port Data Direction 12 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD13 Port Data Direction 13 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD14 Port Data Direction 14 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD15 Port Data Direction 15 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD16 Port Data Direction 16 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD17 Port Data Direction 17 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD18 Port Data Direction 18 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD19 Port Data Direction 19 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD2 Port Data Direction 2 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD20 Port Data Direction 20 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD21 Port Data Direction 21 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD22 Port Data Direction 22 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD23 Port Data Direction 23 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD24 Port Data Direction 24 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD25 Port Data Direction 25 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD26 Port Data Direction 26 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD27 Port Data Direction 27 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD28 Port Data Direction 28 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD29 Port Data Direction 29 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD3 Port Data Direction 3 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD30 Port Data Direction 30 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD31 Port Data Direction 31 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD4 Port Data Direction 4 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD5 Port Data Direction 5 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD6 Port Data Direction 6 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD7 Port Data Direction 7 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD8 Port Data Direction 8 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD9 Port Data Direction 9 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDIR Port Data Input Register 0x10 32 read-only n 0x0 0x0 PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI0 Port Data Input 0 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI1 Port Data Input 1 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI10 Port Data Input 10 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI11 Port Data Input 11 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI12 Port Data Input 12 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI13 Port Data Input 13 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI14 Port Data Input 14 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI15 Port Data Input 15 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI16 Port Data Input 16 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI17 Port Data Input 17 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI18 Port Data Input 18 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI19 Port Data Input 19 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI2 Port Data Input 2 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI20 Port Data Input 20 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI21 Port Data Input 21 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI22 Port Data Input 22 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI23 Port Data Input 23 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI24 Port Data Input 24 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI25 Port Data Input 25 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI26 Port Data Input 26 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI27 Port Data Input 27 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI28 Port Data Input 28 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI29 Port Data Input 29 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI3 Port Data Input 3 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI30 Port Data Input 30 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI31 Port Data Input 31 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI4 Port Data Input 4 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI5 Port Data Input 5 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI6 Port Data Input 6 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI7 Port Data Input 7 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI8 Port Data Input 8 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI9 Port Data Input 9 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDOR Port Data Output Register 0x0 32 read-write n 0x0 0x0 PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO0 Port Data Output 0 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO1 Port Data Output 1 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO10 Port Data Output 10 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO11 Port Data Output 11 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO12 Port Data Output 12 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO13 Port Data Output 13 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO14 Port Data Output 14 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO15 Port Data Output 15 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO16 Port Data Output 16 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO17 Port Data Output 17 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO18 Port Data Output 18 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO19 Port Data Output 19 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO2 Port Data Output 2 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO20 Port Data Output 20 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO21 Port Data Output 21 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO22 Port Data Output 22 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO23 Port Data Output 23 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO24 Port Data Output 24 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO25 Port Data Output 25 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO26 Port Data Output 26 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO27 Port Data Output 27 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO28 Port Data Output 28 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO29 Port Data Output 29 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO3 Port Data Output 3 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO30 Port Data Output 30 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO31 Port Data Output 31 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO4 Port Data Output 4 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO5 Port Data Output 5 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO6 Port Data Output 6 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO7 Port Data Output 7 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO8 Port Data Output 8 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO9 Port Data Output 9 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only n 0x0 0x0 PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO0 Port Set Output 0 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO1 Port Set Output 1 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO10 Port Set Output 10 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO11 Port Set Output 11 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO12 Port Set Output 12 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO13 Port Set Output 13 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO14 Port Set Output 14 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO15 Port Set Output 15 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO16 Port Set Output 16 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO17 Port Set Output 17 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO18 Port Set Output 18 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO19 Port Set Output 19 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO2 Port Set Output 2 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO20 Port Set Output 20 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO21 Port Set Output 21 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO22 Port Set Output 22 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO23 Port Set Output 23 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO24 Port Set Output 24 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO25 Port Set Output 25 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO26 Port Set Output 26 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO27 Port Set Output 27 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO28 Port Set Output 28 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO29 Port Set Output 29 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO3 Port Set Output 3 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO30 Port Set Output 30 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO31 Port Set Output 31 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO4 Port Set Output 4 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO5 Port Set Output 5 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO6 Port Set Output 6 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO7 Port Set Output 7 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO8 Port Set Output 8 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO9 Port Set Output 9 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTOR Port Toggle Output Register 0xC 32 write-only n 0x0 0x0 PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO0 Port Toggle Output 0 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO1 Port Toggle Output 1 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO10 Port Toggle Output 10 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO11 Port Toggle Output 11 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO12 Port Toggle Output 12 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO13 Port Toggle Output 13 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO14 Port Toggle Output 14 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO15 Port Toggle Output 15 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO16 Port Toggle Output 16 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO17 Port Toggle Output 17 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO18 Port Toggle Output 18 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO19 Port Toggle Output 19 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO2 Port Toggle Output 2 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO20 Port Toggle Output 20 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO21 Port Toggle Output 21 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO22 Port Toggle Output 22 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO23 Port Toggle Output 23 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO24 Port Toggle Output 24 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO25 Port Toggle Output 25 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO26 Port Toggle Output 26 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO27 Port Toggle Output 27 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO28 Port Toggle Output 28 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO29 Port Toggle Output 29 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO3 Port Toggle Output 3 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO30 Port Toggle Output 30 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO31 Port Toggle Output 31 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO4 Port Toggle Output 4 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO5 Port Toggle Output 5 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO6 Port Toggle Output 6 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO7 Port Toggle Output 7 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO8 Port Toggle Output 8 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO9 Port Toggle Output 9 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 GPIOC General Purpose Input/Output GPIO 0x0 0x0 0x18 registers n PORTC 61 PCOR Port Clear Output Register 0x8 32 write-only n 0x0 0x0 PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO0 Port Clear Output 0 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO1 Port Clear Output 1 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO10 Port Clear Output 10 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO11 Port Clear Output 11 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO12 Port Clear Output 12 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO13 Port Clear Output 13 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO14 Port Clear Output 14 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO15 Port Clear Output 15 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO16 Port Clear Output 16 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO17 Port Clear Output 17 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO18 Port Clear Output 18 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO19 Port Clear Output 19 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO2 Port Clear Output 2 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO20 Port Clear Output 20 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO21 Port Clear Output 21 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO22 Port Clear Output 22 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO23 Port Clear Output 23 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO24 Port Clear Output 24 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO25 Port Clear Output 25 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO26 Port Clear Output 26 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO27 Port Clear Output 27 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO28 Port Clear Output 28 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO29 Port Clear Output 29 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO3 Port Clear Output 3 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO30 Port Clear Output 30 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO31 Port Clear Output 31 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO4 Port Clear Output 4 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO5 Port Clear Output 5 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO6 Port Clear Output 6 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO7 Port Clear Output 7 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO8 Port Clear Output 8 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO9 Port Clear Output 9 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PDDR Port Data Direction Register 0x14 32 read-write n 0x0 0x0 PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD0 Port Data Direction 0 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD1 Port Data Direction 1 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD10 Port Data Direction 10 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD11 Port Data Direction 11 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD12 Port Data Direction 12 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD13 Port Data Direction 13 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD14 Port Data Direction 14 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD15 Port Data Direction 15 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD16 Port Data Direction 16 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD17 Port Data Direction 17 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD18 Port Data Direction 18 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD19 Port Data Direction 19 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD2 Port Data Direction 2 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD20 Port Data Direction 20 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD21 Port Data Direction 21 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD22 Port Data Direction 22 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD23 Port Data Direction 23 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD24 Port Data Direction 24 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD25 Port Data Direction 25 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD26 Port Data Direction 26 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD27 Port Data Direction 27 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD28 Port Data Direction 28 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD29 Port Data Direction 29 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD3 Port Data Direction 3 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD30 Port Data Direction 30 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD31 Port Data Direction 31 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD4 Port Data Direction 4 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD5 Port Data Direction 5 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD6 Port Data Direction 6 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD7 Port Data Direction 7 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD8 Port Data Direction 8 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD9 Port Data Direction 9 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDIR Port Data Input Register 0x10 32 read-only n 0x0 0x0 PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI0 Port Data Input 0 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI1 Port Data Input 1 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI10 Port Data Input 10 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI11 Port Data Input 11 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI12 Port Data Input 12 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI13 Port Data Input 13 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI14 Port Data Input 14 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI15 Port Data Input 15 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI16 Port Data Input 16 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI17 Port Data Input 17 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI18 Port Data Input 18 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI19 Port Data Input 19 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI2 Port Data Input 2 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI20 Port Data Input 20 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI21 Port Data Input 21 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI22 Port Data Input 22 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI23 Port Data Input 23 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI24 Port Data Input 24 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI25 Port Data Input 25 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI26 Port Data Input 26 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI27 Port Data Input 27 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI28 Port Data Input 28 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI29 Port Data Input 29 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI3 Port Data Input 3 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI30 Port Data Input 30 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI31 Port Data Input 31 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI4 Port Data Input 4 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI5 Port Data Input 5 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI6 Port Data Input 6 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI7 Port Data Input 7 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI8 Port Data Input 8 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI9 Port Data Input 9 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDOR Port Data Output Register 0x0 32 read-write n 0x0 0x0 PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO0 Port Data Output 0 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO1 Port Data Output 1 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO10 Port Data Output 10 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO11 Port Data Output 11 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO12 Port Data Output 12 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO13 Port Data Output 13 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO14 Port Data Output 14 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO15 Port Data Output 15 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO16 Port Data Output 16 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO17 Port Data Output 17 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO18 Port Data Output 18 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO19 Port Data Output 19 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO2 Port Data Output 2 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO20 Port Data Output 20 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO21 Port Data Output 21 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO22 Port Data Output 22 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO23 Port Data Output 23 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO24 Port Data Output 24 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO25 Port Data Output 25 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO26 Port Data Output 26 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO27 Port Data Output 27 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO28 Port Data Output 28 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO29 Port Data Output 29 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO3 Port Data Output 3 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO30 Port Data Output 30 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO31 Port Data Output 31 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO4 Port Data Output 4 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO5 Port Data Output 5 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO6 Port Data Output 6 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO7 Port Data Output 7 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO8 Port Data Output 8 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO9 Port Data Output 9 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only n 0x0 0x0 PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO0 Port Set Output 0 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO1 Port Set Output 1 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO10 Port Set Output 10 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO11 Port Set Output 11 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO12 Port Set Output 12 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO13 Port Set Output 13 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO14 Port Set Output 14 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO15 Port Set Output 15 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO16 Port Set Output 16 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO17 Port Set Output 17 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO18 Port Set Output 18 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO19 Port Set Output 19 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO2 Port Set Output 2 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO20 Port Set Output 20 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO21 Port Set Output 21 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO22 Port Set Output 22 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO23 Port Set Output 23 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO24 Port Set Output 24 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO25 Port Set Output 25 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO26 Port Set Output 26 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO27 Port Set Output 27 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO28 Port Set Output 28 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO29 Port Set Output 29 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO3 Port Set Output 3 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO30 Port Set Output 30 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO31 Port Set Output 31 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO4 Port Set Output 4 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO5 Port Set Output 5 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO6 Port Set Output 6 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO7 Port Set Output 7 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO8 Port Set Output 8 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO9 Port Set Output 9 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTOR Port Toggle Output Register 0xC 32 write-only n 0x0 0x0 PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO0 Port Toggle Output 0 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO1 Port Toggle Output 1 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO10 Port Toggle Output 10 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO11 Port Toggle Output 11 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO12 Port Toggle Output 12 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO13 Port Toggle Output 13 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO14 Port Toggle Output 14 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO15 Port Toggle Output 15 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO16 Port Toggle Output 16 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO17 Port Toggle Output 17 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO18 Port Toggle Output 18 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO19 Port Toggle Output 19 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO2 Port Toggle Output 2 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO20 Port Toggle Output 20 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO21 Port Toggle Output 21 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO22 Port Toggle Output 22 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO23 Port Toggle Output 23 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO24 Port Toggle Output 24 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO25 Port Toggle Output 25 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO26 Port Toggle Output 26 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO27 Port Toggle Output 27 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO28 Port Toggle Output 28 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO29 Port Toggle Output 29 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO3 Port Toggle Output 3 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO30 Port Toggle Output 30 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO31 Port Toggle Output 31 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO4 Port Toggle Output 4 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO5 Port Toggle Output 5 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO6 Port Toggle Output 6 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO7 Port Toggle Output 7 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO8 Port Toggle Output 8 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO9 Port Toggle Output 9 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 GPIOD General Purpose Input/Output GPIO 0x0 0x0 0x18 registers n PORTD 62 PCOR Port Clear Output Register 0x8 32 write-only n 0x0 0x0 PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO0 Port Clear Output 0 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO1 Port Clear Output 1 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO10 Port Clear Output 10 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO11 Port Clear Output 11 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO12 Port Clear Output 12 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO13 Port Clear Output 13 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO14 Port Clear Output 14 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO15 Port Clear Output 15 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO16 Port Clear Output 16 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO17 Port Clear Output 17 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO18 Port Clear Output 18 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO19 Port Clear Output 19 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO2 Port Clear Output 2 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO20 Port Clear Output 20 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO21 Port Clear Output 21 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO22 Port Clear Output 22 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO23 Port Clear Output 23 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO24 Port Clear Output 24 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO25 Port Clear Output 25 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO26 Port Clear Output 26 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO27 Port Clear Output 27 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO28 Port Clear Output 28 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO29 Port Clear Output 29 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO3 Port Clear Output 3 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO30 Port Clear Output 30 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO31 Port Clear Output 31 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO4 Port Clear Output 4 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO5 Port Clear Output 5 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO6 Port Clear Output 6 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO7 Port Clear Output 7 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO8 Port Clear Output 8 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO9 Port Clear Output 9 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PDDR Port Data Direction Register 0x14 32 read-write n 0x0 0x0 PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD0 Port Data Direction 0 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD1 Port Data Direction 1 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD10 Port Data Direction 10 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD11 Port Data Direction 11 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD12 Port Data Direction 12 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD13 Port Data Direction 13 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD14 Port Data Direction 14 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD15 Port Data Direction 15 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD16 Port Data Direction 16 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD17 Port Data Direction 17 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD18 Port Data Direction 18 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD19 Port Data Direction 19 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD2 Port Data Direction 2 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD20 Port Data Direction 20 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD21 Port Data Direction 21 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD22 Port Data Direction 22 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD23 Port Data Direction 23 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD24 Port Data Direction 24 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD25 Port Data Direction 25 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD26 Port Data Direction 26 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD27 Port Data Direction 27 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD28 Port Data Direction 28 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD29 Port Data Direction 29 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD3 Port Data Direction 3 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD30 Port Data Direction 30 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD31 Port Data Direction 31 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD4 Port Data Direction 4 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD5 Port Data Direction 5 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD6 Port Data Direction 6 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD7 Port Data Direction 7 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD8 Port Data Direction 8 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD9 Port Data Direction 9 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDIR Port Data Input Register 0x10 32 read-only n 0x0 0x0 PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI0 Port Data Input 0 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI1 Port Data Input 1 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI10 Port Data Input 10 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI11 Port Data Input 11 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI12 Port Data Input 12 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI13 Port Data Input 13 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI14 Port Data Input 14 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI15 Port Data Input 15 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI16 Port Data Input 16 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI17 Port Data Input 17 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI18 Port Data Input 18 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI19 Port Data Input 19 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI2 Port Data Input 2 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI20 Port Data Input 20 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI21 Port Data Input 21 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI22 Port Data Input 22 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI23 Port Data Input 23 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI24 Port Data Input 24 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI25 Port Data Input 25 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI26 Port Data Input 26 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI27 Port Data Input 27 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI28 Port Data Input 28 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI29 Port Data Input 29 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI3 Port Data Input 3 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI30 Port Data Input 30 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI31 Port Data Input 31 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI4 Port Data Input 4 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI5 Port Data Input 5 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI6 Port Data Input 6 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI7 Port Data Input 7 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI8 Port Data Input 8 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI9 Port Data Input 9 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDOR Port Data Output Register 0x0 32 read-write n 0x0 0x0 PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO0 Port Data Output 0 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO1 Port Data Output 1 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO10 Port Data Output 10 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO11 Port Data Output 11 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO12 Port Data Output 12 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO13 Port Data Output 13 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO14 Port Data Output 14 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO15 Port Data Output 15 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO16 Port Data Output 16 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO17 Port Data Output 17 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO18 Port Data Output 18 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO19 Port Data Output 19 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO2 Port Data Output 2 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO20 Port Data Output 20 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO21 Port Data Output 21 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO22 Port Data Output 22 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO23 Port Data Output 23 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO24 Port Data Output 24 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO25 Port Data Output 25 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO26 Port Data Output 26 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO27 Port Data Output 27 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO28 Port Data Output 28 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO29 Port Data Output 29 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO3 Port Data Output 3 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO30 Port Data Output 30 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO31 Port Data Output 31 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO4 Port Data Output 4 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO5 Port Data Output 5 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO6 Port Data Output 6 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO7 Port Data Output 7 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO8 Port Data Output 8 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO9 Port Data Output 9 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only n 0x0 0x0 PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO0 Port Set Output 0 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO1 Port Set Output 1 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO10 Port Set Output 10 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO11 Port Set Output 11 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO12 Port Set Output 12 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO13 Port Set Output 13 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO14 Port Set Output 14 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO15 Port Set Output 15 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO16 Port Set Output 16 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO17 Port Set Output 17 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO18 Port Set Output 18 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO19 Port Set Output 19 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO2 Port Set Output 2 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO20 Port Set Output 20 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO21 Port Set Output 21 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO22 Port Set Output 22 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO23 Port Set Output 23 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO24 Port Set Output 24 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO25 Port Set Output 25 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO26 Port Set Output 26 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO27 Port Set Output 27 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO28 Port Set Output 28 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO29 Port Set Output 29 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO3 Port Set Output 3 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO30 Port Set Output 30 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO31 Port Set Output 31 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO4 Port Set Output 4 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO5 Port Set Output 5 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO6 Port Set Output 6 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO7 Port Set Output 7 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO8 Port Set Output 8 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO9 Port Set Output 9 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTOR Port Toggle Output Register 0xC 32 write-only n 0x0 0x0 PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO0 Port Toggle Output 0 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO1 Port Toggle Output 1 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO10 Port Toggle Output 10 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO11 Port Toggle Output 11 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO12 Port Toggle Output 12 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO13 Port Toggle Output 13 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO14 Port Toggle Output 14 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO15 Port Toggle Output 15 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO16 Port Toggle Output 16 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO17 Port Toggle Output 17 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO18 Port Toggle Output 18 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO19 Port Toggle Output 19 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO2 Port Toggle Output 2 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO20 Port Toggle Output 20 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO21 Port Toggle Output 21 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO22 Port Toggle Output 22 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO23 Port Toggle Output 23 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO24 Port Toggle Output 24 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO25 Port Toggle Output 25 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO26 Port Toggle Output 26 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO27 Port Toggle Output 27 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO28 Port Toggle Output 28 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO29 Port Toggle Output 29 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO3 Port Toggle Output 3 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO30 Port Toggle Output 30 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO31 Port Toggle Output 31 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO4 Port Toggle Output 4 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO5 Port Toggle Output 5 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO6 Port Toggle Output 6 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO7 Port Toggle Output 7 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO8 Port Toggle Output 8 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO9 Port Toggle Output 9 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 GPIOE General Purpose Input/Output GPIO 0x0 0x0 0x18 registers n PORTE 63 PCOR Port Clear Output Register 0x8 32 write-only n 0x0 0x0 PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO0 Port Clear Output 0 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO1 Port Clear Output 1 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO10 Port Clear Output 10 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO11 Port Clear Output 11 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO12 Port Clear Output 12 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO13 Port Clear Output 13 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO14 Port Clear Output 14 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO15 Port Clear Output 15 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO16 Port Clear Output 16 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO17 Port Clear Output 17 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO18 Port Clear Output 18 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO19 Port Clear Output 19 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO2 Port Clear Output 2 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO20 Port Clear Output 20 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO21 Port Clear Output 21 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO22 Port Clear Output 22 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO23 Port Clear Output 23 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO24 Port Clear Output 24 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO25 Port Clear Output 25 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO26 Port Clear Output 26 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO27 Port Clear Output 27 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO28 Port Clear Output 28 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO29 Port Clear Output 29 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO3 Port Clear Output 3 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO30 Port Clear Output 30 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO31 Port Clear Output 31 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO4 Port Clear Output 4 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO5 Port Clear Output 5 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO6 Port Clear Output 6 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO7 Port Clear Output 7 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO8 Port Clear Output 8 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PTCO9 Port Clear Output 9 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PDDR Port Data Direction Register 0x14 32 read-write n 0x0 0x0 PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD0 Port Data Direction 0 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD1 Port Data Direction 1 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD10 Port Data Direction 10 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD11 Port Data Direction 11 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD12 Port Data Direction 12 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD13 Port Data Direction 13 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD14 Port Data Direction 14 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD15 Port Data Direction 15 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD16 Port Data Direction 16 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD17 Port Data Direction 17 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD18 Port Data Direction 18 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD19 Port Data Direction 19 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD2 Port Data Direction 2 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD20 Port Data Direction 20 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD21 Port Data Direction 21 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD22 Port Data Direction 22 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD23 Port Data Direction 23 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD24 Port Data Direction 24 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD25 Port Data Direction 25 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD26 Port Data Direction 26 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD27 Port Data Direction 27 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD28 Port Data Direction 28 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD29 Port Data Direction 29 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD3 Port Data Direction 3 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD30 Port Data Direction 30 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD31 Port Data Direction 31 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD4 Port Data Direction 4 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD5 Port Data Direction 5 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD6 Port Data Direction 6 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD7 Port Data Direction 7 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD8 Port Data Direction 8 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDD9 Port Data Direction 9 1 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDIR Port Data Input Register 0x10 32 read-only n 0x0 0x0 PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI0 Port Data Input 0 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI1 Port Data Input 1 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI10 Port Data Input 10 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI11 Port Data Input 11 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI12 Port Data Input 12 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI13 Port Data Input 13 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI14 Port Data Input 14 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI15 Port Data Input 15 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI16 Port Data Input 16 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI17 Port Data Input 17 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI18 Port Data Input 18 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI19 Port Data Input 19 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI2 Port Data Input 2 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI20 Port Data Input 20 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI21 Port Data Input 21 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI22 Port Data Input 22 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI23 Port Data Input 23 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI24 Port Data Input 24 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI25 Port Data Input 25 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI26 Port Data Input 26 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI27 Port Data Input 27 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI28 Port Data Input 28 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI29 Port Data Input 29 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI3 Port Data Input 3 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI30 Port Data Input 30 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI31 Port Data Input 31 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI4 Port Data Input 4 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI5 Port Data Input 5 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI6 Port Data Input 6 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI7 Port Data Input 7 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI8 Port Data Input 8 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDI9 Port Data Input 9 1 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDOR Port Data Output Register 0x0 32 read-write n 0x0 0x0 PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO0 Port Data Output 0 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO1 Port Data Output 1 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO10 Port Data Output 10 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO11 Port Data Output 11 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO12 Port Data Output 12 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO13 Port Data Output 13 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO14 Port Data Output 14 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO15 Port Data Output 15 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO16 Port Data Output 16 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO17 Port Data Output 17 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO18 Port Data Output 18 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO19 Port Data Output 19 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO2 Port Data Output 2 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO20 Port Data Output 20 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO21 Port Data Output 21 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO22 Port Data Output 22 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO23 Port Data Output 23 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO24 Port Data Output 24 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO25 Port Data Output 25 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO26 Port Data Output 26 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO27 Port Data Output 27 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO28 Port Data Output 28 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO29 Port Data Output 29 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO3 Port Data Output 3 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO30 Port Data Output 30 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO31 Port Data Output 31 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO4 Port Data Output 4 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO5 Port Data Output 5 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO6 Port Data Output 6 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO7 Port Data Output 7 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO8 Port Data Output 8 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PDO9 Port Data Output 9 1 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only n 0x0 0x0 PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO0 Port Set Output 0 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO1 Port Set Output 1 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO10 Port Set Output 10 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO11 Port Set Output 11 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO12 Port Set Output 12 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO13 Port Set Output 13 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO14 Port Set Output 14 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO15 Port Set Output 15 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO16 Port Set Output 16 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO17 Port Set Output 17 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO18 Port Set Output 18 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO19 Port Set Output 19 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO2 Port Set Output 2 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO20 Port Set Output 20 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO21 Port Set Output 21 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO22 Port Set Output 22 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO23 Port Set Output 23 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO24 Port Set Output 24 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO25 Port Set Output 25 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO26 Port Set Output 26 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO27 Port Set Output 27 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO28 Port Set Output 28 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO29 Port Set Output 29 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO3 Port Set Output 3 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO30 Port Set Output 30 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO31 Port Set Output 31 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO4 Port Set Output 4 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO5 Port Set Output 5 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO6 Port Set Output 6 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO7 Port Set Output 7 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO8 Port Set Output 8 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTSO9 Port Set Output 9 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTOR Port Toggle Output Register 0xC 32 write-only n 0x0 0x0 PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO0 Port Toggle Output 0 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO1 Port Toggle Output 1 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO10 Port Toggle Output 10 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO11 Port Toggle Output 11 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO12 Port Toggle Output 12 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO13 Port Toggle Output 13 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO14 Port Toggle Output 14 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO15 Port Toggle Output 15 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO16 Port Toggle Output 16 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO17 Port Toggle Output 17 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO18 Port Toggle Output 18 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO19 Port Toggle Output 19 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO2 Port Toggle Output 2 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO20 Port Toggle Output 20 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO21 Port Toggle Output 21 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO22 Port Toggle Output 22 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO23 Port Toggle Output 23 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO24 Port Toggle Output 24 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO25 Port Toggle Output 25 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO26 Port Toggle Output 26 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO27 Port Toggle Output 27 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO28 Port Toggle Output 28 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO29 Port Toggle Output 29 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO3 Port Toggle Output 3 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO30 Port Toggle Output 30 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO31 Port Toggle Output 31 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO4 Port Toggle Output 4 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO5 Port Toggle Output 5 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO6 Port Toggle Output 6 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO7 Port Toggle Output 7 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO8 Port Toggle Output 8 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTTO9 Port Toggle Output 9 1 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 I2C0 Inter-Integrated Circuit I2C 0x0 0x0 0xC registers n I2C0 24 A1 I2C Address Register 1 0x0 8 read-write n 0x0 0x0 AD Address 1 7 read-write A2 I2C Address Register 2 0x9 8 read-write n 0x0 0x0 SAD SMBus Address 1 7 read-write C1 I2C Control Register 1 0x2 8 read-write n 0x0 0x0 DMAEN DMA Enable 0 1 read-write 0 All DMA signalling disabled. #0 1 DMA transfer is enabled. While SMB[FACK] = 0, the following conditions trigger the DMA request: a data byte is received, and either address or data is transmitted. (ACK/NACK is automatic) the first byte received matches the A1 register or is a general call address. If any address matching occurs, S[IAAS] and S[TCF] are set. If the direction of transfer is known from master to slave, then it is not required to check S[SRW]. With this assumption, DMA can also be used in this case. In other cases, if the master reads data from the slave, then it is required to rewrite the C1 register operation. With this assumption, DMA cannot be used. When FACK = 1, an address or a data byte is transmitted. #1 IICEN I2C Enable 7 1 read-write 0 Disabled #0 1 Enabled #1 IICIE I2C Interrupt Enable 6 1 read-write 0 Disabled #0 1 Enabled #1 MST Master Mode Select 5 1 read-write 0 Slave mode #0 1 Master mode #1 RSTA Repeat START 2 1 write-only TX Transmit Mode Select 4 1 read-write 0 Receive #0 1 Transmit #1 TXAK Transmit Acknowledge Enable 3 1 read-write 0 An acknowledge signal is sent to the bus on the following receiving byte (if FACK is cleared) or the current receiving byte (if FACK is set). #0 1 No acknowledge signal is sent to the bus on the following receiving data byte (if FACK is cleared) or the current receiving data byte (if FACK is set). #1 WUEN Wakeup Enable 1 1 read-write 0 Normal operation. No interrupt generated when address matching in low power mode. #0 1 Enables the wakeup function in low power mode. #1 C2 I2C Control Register 2 0x5 8 read-write n 0x0 0x0 AD Slave Address 0 3 read-write ADEXT Address Extension 6 1 read-write 0 7-bit address scheme #0 1 10-bit address scheme #1 GCAEN General Call Address Enable 7 1 read-write 0 Disabled #0 1 Enabled #1 HDRS High Drive Select 5 1 read-write 0 Normal drive mode #0 1 High drive mode #1 RMEN Range Address Matching Enable 3 1 read-write 0 Range mode disabled. No address matching occurs for an address within the range of values of the A1 and RA registers. #0 1 Range mode enabled. Address matching occurs when a slave receives an address within the range of values of the A1 and RA registers. #1 SBRC Slave Baud Rate Control 4 1 read-write 0 The slave baud rate follows the master baud rate and clock stretching may occur #0 1 Slave baud rate is independent of the master baud rate #1 D I2C Data I/O register 0x4 8 read-write n 0x0 0x0 DATA Data 0 8 read-write F I2C Frequency Divider register 0x1 8 read-write n 0x0 0x0 ICR ClockRate 0 6 read-write MULT Multiplier Factor 6 2 read-write 00 mul = 1 #00 01 mul = 2 #01 10 mul = 4 #10 FLT I2C Programmable Input Glitch Filter register 0x6 8 read-write n 0x0 0x0 FLT I2C Programmable Filter Factor 0 4 read-write 0 No filter/bypass #0000 SHEN Stop Hold Enable 7 1 read-write 0 Stop holdoff is disabled. The MCU's entry to stop mode is not gated. #0 1 Stop holdoff is enabled. #1 SSIE I2C Bus Stop or Start Interrupt Enable 5 1 read-write 0 Stop or start detection interrupt is disabled #0 1 Stop or start detection interrupt is enabled #1 STARTF I2C Bus Start Detect Flag 4 1 read-write 0 No start happens on I2C bus #0 1 Start detected on I2C bus #1 STOPF I2C Bus Stop Detect Flag 6 1 read-write 0 No stop happens on I2C bus #0 1 Stop detected on I2C bus #1 RA I2C Range Address register 0x7 8 read-write n 0x0 0x0 RAD Range Slave Address 1 7 read-write S I2C Status register 0x3 8 read-write n 0x0 0x0 ARBL Arbitration Lost 4 1 read-write 0 Standard bus operation. #0 1 Loss of arbitration. #1 BUSY Bus Busy 5 1 read-only 0 Bus is idle #0 1 Bus is busy #1 IAAS Addressed As A Slave 6 1 read-write 0 Not addressed #0 1 Addressed as a slave #1 IICIF Interrupt Flag 1 1 read-write 0 No interrupt pending #0 1 Interrupt pending #1 RAM Range Address Match 3 1 read-write 0 Not addressed #0 1 Addressed as a slave #1 RXAK Receive Acknowledge 0 1 read-only 0 Acknowledge signal was received after the completion of one byte of data transmission on the bus #0 1 No acknowledge signal detected #1 SRW Slave Read/Write 2 1 read-only 0 Slave receive, master writing to slave #0 1 Slave transmit, master reading from slave #1 TCF Transfer Complete Flag 7 1 read-only 0 Transfer in progress #0 1 Transfer complete #1 SLTH I2C SCL Low Timeout Register High 0xA 8 read-write n 0x0 0x0 SSLT Most significant byte of SCL low timeout value that determines the timeout period of SCL low. 0 8 read-write SLTL I2C SCL Low Timeout Register Low 0xB 8 read-write n 0x0 0x0 SSLT Least significant byte of SCL low timeout value that determines the timeout period of SCL low. 0 8 read-write SMB I2C SMBus Control and Status register 0x8 8 read-write n 0x0 0x0 ALERTEN SMBus Alert Response Address Enable 6 1 read-write 0 SMBus alert response address matching is disabled #0 1 SMBus alert response address matching is enabled #1 FACK Fast NACK/ACK Enable 7 1 read-write 0 An ACK or NACK is sent on the following receiving data byte #0 1 Writing 0 to TXAK after receiving a data byte generates an ACK. Writing 1 to TXAK after receiving a data byte generates a NACK. #1 SHTF1 SCL High Timeout Flag 1 2 1 read-only 0 No SCL high and SDA high timeout occurs #0 1 SCL high and SDA high timeout occurs #1 SHTF2 SCL High Timeout Flag 2 1 1 read-write 0 No SCL high and SDA low timeout occurs #0 1 SCL high and SDA low timeout occurs #1 SHTF2IE SHTF2 Interrupt Enable 0 1 read-write 0 SHTF2 interrupt is disabled #0 1 SHTF2 interrupt is enabled #1 SIICAEN Second I2C Address Enable 5 1 read-write 0 I2C address register 2 matching is disabled #0 1 I2C address register 2 matching is enabled #1 SLTF SCL Low Timeout Flag 3 1 read-write 0 No low timeout occurs #0 1 Low timeout occurs #1 TCKSEL Timeout Counter Clock Select 4 1 read-write 0 Timeout counter counts at the frequency of the I2C module clock / 64 #0 1 Timeout counter counts at the frequency of the I2C module clock #1 I2C1 Inter-Integrated Circuit I2C 0x0 0x0 0xC registers n I2C1 25 A1 I2C Address Register 1 0x0 8 read-write n 0x0 0x0 AD Address 1 7 read-write A2 I2C Address Register 2 0x9 8 read-write n 0x0 0x0 SAD SMBus Address 1 7 read-write C1 I2C Control Register 1 0x2 8 read-write n 0x0 0x0 DMAEN DMA Enable 0 1 read-write 0 All DMA signalling disabled. #0 1 DMA transfer is enabled. While SMB[FACK] = 0, the following conditions trigger the DMA request: a data byte is received, and either address or data is transmitted. (ACK/NACK is automatic) the first byte received matches the A1 register or is a general call address. If any address matching occurs, S[IAAS] and S[TCF] are set. If the direction of transfer is known from master to slave, then it is not required to check S[SRW]. With this assumption, DMA can also be used in this case. In other cases, if the master reads data from the slave, then it is required to rewrite the C1 register operation. With this assumption, DMA cannot be used. When FACK = 1, an address or a data byte is transmitted. #1 IICEN I2C Enable 7 1 read-write 0 Disabled #0 1 Enabled #1 IICIE I2C Interrupt Enable 6 1 read-write 0 Disabled #0 1 Enabled #1 MST Master Mode Select 5 1 read-write 0 Slave mode #0 1 Master mode #1 RSTA Repeat START 2 1 write-only TX Transmit Mode Select 4 1 read-write 0 Receive #0 1 Transmit #1 TXAK Transmit Acknowledge Enable 3 1 read-write 0 An acknowledge signal is sent to the bus on the following receiving byte (if FACK is cleared) or the current receiving byte (if FACK is set). #0 1 No acknowledge signal is sent to the bus on the following receiving data byte (if FACK is cleared) or the current receiving data byte (if FACK is set). #1 WUEN Wakeup Enable 1 1 read-write 0 Normal operation. No interrupt generated when address matching in low power mode. #0 1 Enables the wakeup function in low power mode. #1 C2 I2C Control Register 2 0x5 8 read-write n 0x0 0x0 AD Slave Address 0 3 read-write ADEXT Address Extension 6 1 read-write 0 7-bit address scheme #0 1 10-bit address scheme #1 GCAEN General Call Address Enable 7 1 read-write 0 Disabled #0 1 Enabled #1 HDRS High Drive Select 5 1 read-write 0 Normal drive mode #0 1 High drive mode #1 RMEN Range Address Matching Enable 3 1 read-write 0 Range mode disabled. No address matching occurs for an address within the range of values of the A1 and RA registers. #0 1 Range mode enabled. Address matching occurs when a slave receives an address within the range of values of the A1 and RA registers. #1 SBRC Slave Baud Rate Control 4 1 read-write 0 The slave baud rate follows the master baud rate and clock stretching may occur #0 1 Slave baud rate is independent of the master baud rate #1 D I2C Data I/O register 0x4 8 read-write n 0x0 0x0 DATA Data 0 8 read-write F I2C Frequency Divider register 0x1 8 read-write n 0x0 0x0 ICR ClockRate 0 6 read-write MULT Multiplier Factor 6 2 read-write 00 mul = 1 #00 01 mul = 2 #01 10 mul = 4 #10 FLT I2C Programmable Input Glitch Filter register 0x6 8 read-write n 0x0 0x0 FLT I2C Programmable Filter Factor 0 4 read-write 0 No filter/bypass #0000 SHEN Stop Hold Enable 7 1 read-write 0 Stop holdoff is disabled. The MCU's entry to stop mode is not gated. #0 1 Stop holdoff is enabled. #1 SSIE I2C Bus Stop or Start Interrupt Enable 5 1 read-write 0 Stop or start detection interrupt is disabled #0 1 Stop or start detection interrupt is enabled #1 STARTF I2C Bus Start Detect Flag 4 1 read-write 0 No start happens on I2C bus #0 1 Start detected on I2C bus #1 STOPF I2C Bus Stop Detect Flag 6 1 read-write 0 No stop happens on I2C bus #0 1 Stop detected on I2C bus #1 RA I2C Range Address register 0x7 8 read-write n 0x0 0x0 RAD Range Slave Address 1 7 read-write S I2C Status register 0x3 8 read-write n 0x0 0x0 ARBL Arbitration Lost 4 1 read-write 0 Standard bus operation. #0 1 Loss of arbitration. #1 BUSY Bus Busy 5 1 read-only 0 Bus is idle #0 1 Bus is busy #1 IAAS Addressed As A Slave 6 1 read-write 0 Not addressed #0 1 Addressed as a slave #1 IICIF Interrupt Flag 1 1 read-write 0 No interrupt pending #0 1 Interrupt pending #1 RAM Range Address Match 3 1 read-write 0 Not addressed #0 1 Addressed as a slave #1 RXAK Receive Acknowledge 0 1 read-only 0 Acknowledge signal was received after the completion of one byte of data transmission on the bus #0 1 No acknowledge signal detected #1 SRW Slave Read/Write 2 1 read-only 0 Slave receive, master writing to slave #0 1 Slave transmit, master reading from slave #1 TCF Transfer Complete Flag 7 1 read-only 0 Transfer in progress #0 1 Transfer complete #1 SLTH I2C SCL Low Timeout Register High 0xA 8 read-write n 0x0 0x0 SSLT Most significant byte of SCL low timeout value that determines the timeout period of SCL low. 0 8 read-write SLTL I2C SCL Low Timeout Register Low 0xB 8 read-write n 0x0 0x0 SSLT Least significant byte of SCL low timeout value that determines the timeout period of SCL low. 0 8 read-write SMB I2C SMBus Control and Status register 0x8 8 read-write n 0x0 0x0 ALERTEN SMBus Alert Response Address Enable 6 1 read-write 0 SMBus alert response address matching is disabled #0 1 SMBus alert response address matching is enabled #1 FACK Fast NACK/ACK Enable 7 1 read-write 0 An ACK or NACK is sent on the following receiving data byte #0 1 Writing 0 to TXAK after receiving a data byte generates an ACK. Writing 1 to TXAK after receiving a data byte generates a NACK. #1 SHTF1 SCL High Timeout Flag 1 2 1 read-only 0 No SCL high and SDA high timeout occurs #0 1 SCL high and SDA high timeout occurs #1 SHTF2 SCL High Timeout Flag 2 1 1 read-write 0 No SCL high and SDA low timeout occurs #0 1 SCL high and SDA low timeout occurs #1 SHTF2IE SHTF2 Interrupt Enable 0 1 read-write 0 SHTF2 interrupt is disabled #0 1 SHTF2 interrupt is enabled #1 SIICAEN Second I2C Address Enable 5 1 read-write 0 I2C address register 2 matching is disabled #0 1 I2C address register 2 matching is enabled #1 SLTF SCL Low Timeout Flag 3 1 read-write 0 No low timeout occurs #0 1 Low timeout occurs #1 TCKSEL Timeout Counter Clock Select 4 1 read-write 0 Timeout counter counts at the frequency of the I2C module clock / 64 #0 1 Timeout counter counts at the frequency of the I2C module clock #1 I2S0 Inter-IC Sound / Synchronous Audio Interface I2S0 0x0 0x0 0x108 registers n I2S0_Tx 28 I2S0_Rx 29 MCR SAI MCLK Control Register 0x100 32 read-write n 0x0 0x0 DUF Divider Update Flag 31 1 read-only 0 MCLK divider ratio is not being updated currently. #0 1 MCLK divider ratio is updating on-the-fly. Further updates to the MCLK divider ratio are blocked while this flag remains set. #1 MICS MCLK Input Clock Select 24 2 read-write 00 MCLK divider input clock 0 selected. #00 01 MCLK divider input clock 1 selected. #01 10 MCLK divider input clock 2 selected. #10 11 MCLK divider input clock 3 selected. #11 MOE MCLK Output Enable 30 1 read-write 0 MCLK signal pin is configured as an input that bypasses the MCLK divider. #0 1 MCLK signal pin is configured as an output from the MCLK divider and the MCLK divider is enabled. #1 MDR SAI MCLK Divide Register 0x104 32 read-write n 0x0 0x0 DIVIDE MCLK Divide 0 12 read-write FRACT MCLK Fraction 12 8 read-write RCR1 SAI Receive Configuration 1 Register 0x84 32 read-write n 0x0 0x0 RFW Receive FIFO Watermark 0 3 read-write RCR2 SAI Receive Configuration 2 Register 0x88 32 read-write n 0x0 0x0 BCD Bit Clock Direction 24 1 read-write 0 Bit clock is generated externally in Slave mode. #0 1 Bit clock is generated internally in Master mode. #1 BCI Bit Clock Input 28 1 read-write 0 No effect. #0 1 Internal logic is clocked as if bit clock was externally generated. #1 BCP Bit Clock Polarity 25 1 read-write 0 Bit Clock is active high with drive outputs on rising edge and sample inputs on falling edge. #0 1 Bit Clock is active low with drive outputs on falling edge and sample inputs on rising edge. #1 BCS Bit Clock Swap 29 1 read-write 0 Use the normal bit clock source. #0 1 Swap the bit clock source. #1 DIV Bit Clock Divide 0 8 read-write MSEL MCLK Select 26 2 read-write 00 Bus Clock selected. #00 01 Master Clock (MCLK) 1 option selected. #01 10 Master Clock (MCLK) 2 option selected. #10 11 Master Clock (MCLK) 3 option selected. #11 SYNC Synchronous Mode 30 2 read-write 00 Asynchronous mode. #00 01 Synchronous with transmitter. #01 10 Synchronous with another SAI receiver. #10 11 Synchronous with another SAI transmitter. #11 RCR3 SAI Receive Configuration 3 Register 0x8C 32 read-write n 0x0 0x0 RCE Receive Channel Enable 16 1 read-write 0 Receive data channel N is disabled. #0 1 Receive data channel N is enabled. #1 WDFL Word Flag Configuration 0 4 read-write RCR4 SAI Receive Configuration 4 Register 0x90 32 read-write n 0x0 0x0 FCONT FIFO Continue on Error 28 1 read-write 0 On FIFO error, the SAI will continue from the start of the next frame after the FIFO error flag has been cleared. #0 1 On FIFO error, the SAI will continue from the same word that caused the FIFO error to set after the FIFO warning flag has been cleared. #1 FPACK FIFO Packing Mode 24 2 read-write 00 FIFO packing is disabled #00 10 8-bit FIFO packing is enabled #10 11 16-bit FIFO packing is enabled #11 FRSZ Frame Size 16 4 read-write FSD Frame Sync Direction 0 1 read-write 0 Frame Sync is generated externally in Slave mode. #0 1 Frame Sync is generated internally in Master mode. #1 FSE Frame Sync Early 3 1 read-write 0 Frame sync asserts with the first bit of the frame. #0 1 Frame sync asserts one bit before the first bit of the frame. #1 FSP Frame Sync Polarity 1 1 read-write 0 Frame sync is active high. #0 1 Frame sync is active low. #1 MF MSB First 4 1 read-write 0 LSB is received first. #0 1 MSB is received first. #1 ONDEM On Demand Mode 2 1 read-write 0 Internal frame sync is generated continuously. #0 1 Internal frame sync is generated when the FIFO warning flag is clear. #1 SYWD Sync Width 8 5 read-write RCR5 SAI Receive Configuration 5 Register 0x94 32 read-write n 0x0 0x0 FBT First Bit Shifted 8 5 read-write W0W Word 0 Width 16 5 read-write WNW Word N Width 24 5 read-write RCSR SAI Receive Control Register 0x80 32 read-write n 0x0 0x0 BCE Bit Clock Enable 28 1 read-write 0 Receive bit clock is disabled. #0 1 Receive bit clock is enabled. #1 DBGE Debug Enable 29 1 read-write 0 Receiver is disabled in Debug mode, after completing the current frame. #0 1 Receiver is enabled in Debug mode. #1 FEF FIFO Error Flag 18 1 read-write 0 Receive overflow not detected. #0 1 Receive overflow detected. #1 FEIE FIFO Error Interrupt Enable 10 1 read-write 0 Disables the interrupt. #0 1 Enables the interrupt. #1 FR FIFO Reset 25 1 write-only 0 No effect. #0 1 FIFO reset. #1 FRDE FIFO Request DMA Enable 0 1 read-write 0 Disables the DMA request. #0 1 Enables the DMA request. #1 FRF FIFO Request Flag 16 1 read-only 0 Receive FIFO watermark not reached. #0 1 Receive FIFO watermark has been reached. #1 FRIE FIFO Request Interrupt Enable 8 1 read-write 0 Disables the interrupt. #0 1 Enables the interrupt. #1 FWDE FIFO Warning DMA Enable 1 1 read-write 0 Disables the DMA request. #0 1 Enables the DMA request. #1 FWF FIFO Warning Flag 17 1 read-only 0 No enabled receive FIFO is full. #0 1 Enabled receive FIFO is full. #1 FWIE FIFO Warning Interrupt Enable 9 1 read-write 0 Disables the interrupt. #0 1 Enables the interrupt. #1 RE Receiver Enable 31 1 read-write 0 Receiver is disabled. #0 1 Receiver is enabled, or receiver has been disabled and has not yet reached end of frame. #1 SEF Sync Error Flag 19 1 read-write 0 Sync error not detected. #0 1 Frame sync error detected. #1 SEIE Sync Error Interrupt Enable 11 1 read-write 0 Disables interrupt. #0 1 Enables interrupt. #1 SR Software Reset 24 1 read-write 0 No effect. #0 1 Software reset. #1 STOPE Stop Enable 30 1 read-write 0 Receiver disabled in Stop mode. #0 1 Receiver enabled in Stop mode. #1 WSF Word Start Flag 20 1 read-write 0 Start of word not detected. #0 1 Start of word detected. #1 WSIE Word Start Interrupt Enable 12 1 read-write 0 Disables interrupt. #0 1 Enables interrupt. #1 RDR SAI Receive Data Register 0xA0 32 read-only n 0x0 0x0 RDR Receive Data Register 0 32 read-only RFR SAI Receive FIFO Register 0xC0 32 read-only n 0x0 0x0 RFP Read FIFO Pointer 0 4 read-only WFP Write FIFO Pointer 16 4 read-only RMR SAI Receive Mask Register 0xE0 32 read-write n 0x0 0x0 RWM Receive Word Mask 0 16 read-write 0 Word N is enabled. #0 1 Word N is masked. #1 RWM0 Receive Word Mask 0 1 read-write 0 Word N is enabled. #0 1 Word N is masked. #1 RWM1 Receive Word Mask 1 1 read-write 0 Word N is enabled. #0 1 Word N is masked. #1 RWM10 Receive Word Mask 10 1 read-write 0 Word N is enabled. #0 1 Word N is masked. #1 RWM11 Receive Word Mask 11 1 read-write 0 Word N is enabled. #0 1 Word N is masked. #1 RWM12 Receive Word Mask 12 1 read-write 0 Word N is enabled. #0 1 Word N is masked. #1 RWM13 Receive Word Mask 13 1 read-write 0 Word N is enabled. #0 1 Word N is masked. #1 RWM14 Receive Word Mask 14 1 read-write 0 Word N is enabled. #0 1 Word N is masked. #1 RWM15 Receive Word Mask 15 1 read-write 0 Word N is enabled. #0 1 Word N is masked. #1 RWM2 Receive Word Mask 2 1 read-write 0 Word N is enabled. #0 1 Word N is masked. #1 RWM3 Receive Word Mask 3 1 read-write 0 Word N is enabled. #0 1 Word N is masked. #1 RWM4 Receive Word Mask 4 1 read-write 0 Word N is enabled. #0 1 Word N is masked. #1 RWM5 Receive Word Mask 5 1 read-write 0 Word N is enabled. #0 1 Word N is masked. #1 RWM6 Receive Word Mask 6 1 read-write 0 Word N is enabled. #0 1 Word N is masked. #1 RWM7 Receive Word Mask 7 1 read-write 0 Word N is enabled. #0 1 Word N is masked. #1 RWM8 Receive Word Mask 8 1 read-write 0 Word N is enabled. #0 1 Word N is masked. #1 RWM9 Receive Word Mask 9 1 read-write 0 Word N is enabled. #0 1 Word N is masked. #1 TCR1 SAI Transmit Configuration 1 Register 0x4 32 read-write n 0x0 0x0 TFW Transmit FIFO Watermark 0 3 read-write TCR2 SAI Transmit Configuration 2 Register 0x8 32 read-write n 0x0 0x0 BCD Bit Clock Direction 24 1 read-write 0 Bit clock is generated externally in Slave mode. #0 1 Bit clock is generated internally in Master mode. #1 BCI Bit Clock Input 28 1 read-write 0 No effect. #0 1 Internal logic is clocked as if bit clock was externally generated. #1 BCP Bit Clock Polarity 25 1 read-write 0 Bit clock is active high with drive outputs on rising edge and sample inputs on falling edge. #0 1 Bit clock is active low with drive outputs on falling edge and sample inputs on rising edge. #1 BCS Bit Clock Swap 29 1 read-write 0 Use the normal bit clock source. #0 1 Swap the bit clock source. #1 DIV Bit Clock Divide 0 8 read-write MSEL MCLK Select 26 2 read-write 00 Bus Clock selected. #00 01 Master Clock (MCLK) 1 option selected. #01 10 Master Clock (MCLK) 2 option selected. #10 11 Master Clock (MCLK) 3 option selected. #11 SYNC Synchronous Mode 30 2 read-write 00 Asynchronous mode. #00 01 Synchronous with receiver. #01 10 Synchronous with another SAI transmitter. #10 11 Synchronous with another SAI receiver. #11 TCR3 SAI Transmit Configuration 3 Register 0xC 32 read-write n 0x0 0x0 TCE Transmit Channel Enable 16 1 read-write 0 Transmit data channel N is disabled. #0 1 Transmit data channel N is enabled. #1 WDFL Word Flag Configuration 0 4 read-write TCR4 SAI Transmit Configuration 4 Register 0x10 32 read-write n 0x0 0x0 FCONT FIFO Continue on Error 28 1 read-write 0 On FIFO error, the SAI will continue from the start of the next frame after the FIFO error flag has been cleared. #0 1 On FIFO error, the SAI will continue from the same word that caused the FIFO error to set after the FIFO warning flag has been cleared. #1 FPACK FIFO Packing Mode 24 2 read-write 00 FIFO packing is disabled #00 10 8-bit FIFO packing is enabled #10 11 16-bit FIFO packing is enabled #11 FRSZ Frame size 16 4 read-write FSD Frame Sync Direction 0 1 read-write 0 Frame sync is generated externally in Slave mode. #0 1 Frame sync is generated internally in Master mode. #1 FSE Frame Sync Early 3 1 read-write 0 Frame sync asserts with the first bit of the frame. #0 1 Frame sync asserts one bit before the first bit of the frame. #1 FSP Frame Sync Polarity 1 1 read-write 0 Frame sync is active high. #0 1 Frame sync is active low. #1 MF MSB First 4 1 read-write 0 LSB is transmitted first. #0 1 MSB is transmitted first. #1 ONDEM On Demand Mode 2 1 read-write 0 Internal frame sync is generated continuously. #0 1 Internal frame sync is generated when the FIFO warning flag is clear. #1 SYWD Sync Width 8 5 read-write TCR5 SAI Transmit Configuration 5 Register 0x14 32 read-write n 0x0 0x0 FBT First Bit Shifted 8 5 read-write W0W Word 0 Width 16 5 read-write WNW Word N Width 24 5 read-write TCSR SAI Transmit Control Register 0x0 32 read-write n 0x0 0x0 BCE Bit Clock Enable 28 1 read-write 0 Transmit bit clock is disabled. #0 1 Transmit bit clock is enabled. #1 DBGE Debug Enable 29 1 read-write 0 Transmitter is disabled in Debug mode, after completing the current frame. #0 1 Transmitter is enabled in Debug mode. #1 FEF FIFO Error Flag 18 1 read-write 0 Transmit underrun not detected. #0 1 Transmit underrun detected. #1 FEIE FIFO Error Interrupt Enable 10 1 read-write 0 Disables the interrupt. #0 1 Enables the interrupt. #1 FR FIFO Reset 25 1 write-only 0 No effect. #0 1 FIFO reset. #1 FRDE FIFO Request DMA Enable 0 1 read-write 0 Disables the DMA request. #0 1 Enables the DMA request. #1 FRF FIFO Request Flag 16 1 read-only 0 Transmit FIFO watermark has not been reached. #0 1 Transmit FIFO watermark has been reached. #1 FRIE FIFO Request Interrupt Enable 8 1 read-write 0 Disables the interrupt. #0 1 Enables the interrupt. #1 FWDE FIFO Warning DMA Enable 1 1 read-write 0 Disables the DMA request. #0 1 Enables the DMA request. #1 FWF FIFO Warning Flag 17 1 read-only 0 No enabled transmit FIFO is empty. #0 1 Enabled transmit FIFO is empty. #1 FWIE FIFO Warning Interrupt Enable 9 1 read-write 0 Disables the interrupt. #0 1 Enables the interrupt. #1 SEF Sync Error Flag 19 1 read-write 0 Sync error not detected. #0 1 Frame sync error detected. #1 SEIE Sync Error Interrupt Enable 11 1 read-write 0 Disables interrupt. #0 1 Enables interrupt. #1 SR Software Reset 24 1 read-write 0 No effect. #0 1 Software reset. #1 STOPE Stop Enable 30 1 read-write 0 Transmitter disabled in Stop mode. #0 1 Transmitter enabled in Stop mode. #1 TE Transmitter Enable 31 1 read-write 0 Transmitter is disabled. #0 1 Transmitter is enabled, or transmitter has been disabled and has not yet reached end of frame. #1 WSF Word Start Flag 20 1 read-write 0 Start of word not detected. #0 1 Start of word detected. #1 WSIE Word Start Interrupt Enable 12 1 read-write 0 Disables interrupt. #0 1 Enables interrupt. #1 TDR SAI Transmit Data Register 0x20 32 write-only n 0x0 0x0 TDR Transmit Data Register 0 32 write-only TFR SAI Transmit FIFO Register 0x40 32 read-only n 0x0 0x0 RFP Read FIFO Pointer 0 4 read-only WFP Write FIFO Pointer 16 4 read-only TMR SAI Transmit Mask Register 0x60 32 read-write n 0x0 0x0 TWM Transmit Word Mask 0 16 read-write 0 Word N is enabled. #0 1 Word N is masked. The transmit data pins are tri-stated when masked. #1 TWM0 Transmit Word Mask 0 1 read-write 0 Word N is enabled. #0 1 Word N is masked. The transmit data pins are tri-stated when masked. #1 TWM1 Transmit Word Mask 1 1 read-write 0 Word N is enabled. #0 1 Word N is masked. The transmit data pins are tri-stated when masked. #1 TWM10 Transmit Word Mask 10 1 read-write 0 Word N is enabled. #0 1 Word N is masked. The transmit data pins are tri-stated when masked. #1 TWM11 Transmit Word Mask 11 1 read-write 0 Word N is enabled. #0 1 Word N is masked. The transmit data pins are tri-stated when masked. #1 TWM12 Transmit Word Mask 12 1 read-write 0 Word N is enabled. #0 1 Word N is masked. The transmit data pins are tri-stated when masked. #1 TWM13 Transmit Word Mask 13 1 read-write 0 Word N is enabled. #0 1 Word N is masked. The transmit data pins are tri-stated when masked. #1 TWM14 Transmit Word Mask 14 1 read-write 0 Word N is enabled. #0 1 Word N is masked. The transmit data pins are tri-stated when masked. #1 TWM15 Transmit Word Mask 15 1 read-write 0 Word N is enabled. #0 1 Word N is masked. The transmit data pins are tri-stated when masked. #1 TWM2 Transmit Word Mask 2 1 read-write 0 Word N is enabled. #0 1 Word N is masked. The transmit data pins are tri-stated when masked. #1 TWM3 Transmit Word Mask 3 1 read-write 0 Word N is enabled. #0 1 Word N is masked. The transmit data pins are tri-stated when masked. #1 TWM4 Transmit Word Mask 4 1 read-write 0 Word N is enabled. #0 1 Word N is masked. The transmit data pins are tri-stated when masked. #1 TWM5 Transmit Word Mask 5 1 read-write 0 Word N is enabled. #0 1 Word N is masked. The transmit data pins are tri-stated when masked. #1 TWM6 Transmit Word Mask 6 1 read-write 0 Word N is enabled. #0 1 Word N is masked. The transmit data pins are tri-stated when masked. #1 TWM7 Transmit Word Mask 7 1 read-write 0 Word N is enabled. #0 1 Word N is masked. The transmit data pins are tri-stated when masked. #1 TWM8 Transmit Word Mask 8 1 read-write 0 Word N is enabled. #0 1 Word N is masked. The transmit data pins are tri-stated when masked. #1 TWM9 Transmit Word Mask 9 1 read-write 0 Word N is enabled. #0 1 Word N is masked. The transmit data pins are tri-stated when masked. #1 LLWU Low leakage wakeup unit LLWU 0x0 0x0 0xA registers n LLWU 21 LLW 21 F1 LLWU Flag 1 register 0x5 8 read-write n 0x0 0x0 WUF0 Wakeup Flag For LLWU_P0 0 1 read-write 0 LLWU_P0 input was not a wakeup source #0 1 LLWU_P0 input was a wakeup source #1 WUF1 Wakeup Flag For LLWU_P1 1 1 read-write 0 LLWU_P1 input was not a wakeup source #0 1 LLWU_P1 input was a wakeup source #1 WUF2 Wakeup Flag For LLWU_P2 2 1 read-write 0 LLWU_P2 input was not a wakeup source #0 1 LLWU_P2 input was a wakeup source #1 WUF3 Wakeup Flag For LLWU_P3 3 1 read-write 0 LLWU_P3 input was not a wake-up source #0 1 LLWU_P3 input was a wake-up source #1 WUF4 Wakeup Flag For LLWU_P4 4 1 read-write 0 LLWU_P4 input was not a wakeup source #0 1 LLWU_P4 input was a wakeup source #1 WUF5 Wakeup Flag For LLWU_P5 5 1 read-write 0 LLWU_P5 input was not a wakeup source #0 1 LLWU_P5 input was a wakeup source #1 WUF6 Wakeup Flag For LLWU_P6 6 1 read-write 0 LLWU_P6 input was not a wakeup source #0 1 LLWU_P6 input was a wakeup source #1 WUF7 Wakeup Flag For LLWU_P7 7 1 read-write 0 LLWU_P7 input was not a wakeup source #0 1 LLWU_P7 input was a wakeup source #1 F2 LLWU Flag 2 register 0x6 8 read-write n 0x0 0x0 WUF10 Wakeup Flag For LLWU_P10 2 1 read-write 0 LLWU_P10 input was not a wakeup source #0 1 LLWU_P10 input was a wakeup source #1 WUF11 Wakeup Flag For LLWU_P11 3 1 read-write 0 LLWU_P11 input was not a wakeup source #0 1 LLWU_P11 input was a wakeup source #1 WUF12 Wakeup Flag For LLWU_P12 4 1 read-write 0 LLWU_P12 input was not a wakeup source #0 1 LLWU_P12 input was a wakeup source #1 WUF13 Wakeup Flag For LLWU_P13 5 1 read-write 0 LLWU_P13 input was not a wakeup source #0 1 LLWU_P13 input was a wakeup source #1 WUF14 Wakeup Flag For LLWU_P14 6 1 read-write 0 LLWU_P14 input was not a wakeup source #0 1 LLWU_P14 input was a wakeup source #1 WUF15 Wakeup Flag For LLWU_P15 7 1 read-write 0 LLWU_P15 input was not a wakeup source #0 1 LLWU_P15 input was a wakeup source #1 WUF8 Wakeup Flag For LLWU_P8 0 1 read-write 0 LLWU_P8 input was not a wakeup source #0 1 LLWU_P8 input was a wakeup source #1 WUF9 Wakeup Flag For LLWU_P9 1 1 read-write 0 LLWU_P9 input was not a wakeup source #0 1 LLWU_P9 input was a wakeup source #1 F3 LLWU Flag 3 register 0x7 8 read-only n 0x0 0x0 MWUF0 Wakeup flag For module 0 0 1 read-only 0 Module 0 input was not a wakeup source #0 1 Module 0 input was a wakeup source #1 MWUF1 Wakeup flag For module 1 1 1 read-only 0 Module 1 input was not a wakeup source #0 1 Module 1 input was a wakeup source #1 MWUF2 Wakeup flag For module 2 2 1 read-only 0 Module 2 input was not a wakeup source #0 1 Module 2 input was a wakeup source #1 MWUF3 Wakeup flag For module 3 3 1 read-only 0 Module 3 input was not a wakeup source #0 1 Module 3 input was a wakeup source #1 MWUF4 Wakeup flag For module 4 4 1 read-only 0 Module 4 input was not a wakeup source #0 1 Module 4 input was a wakeup source #1 MWUF5 Wakeup flag For module 5 5 1 read-only 0 Module 5 input was not a wakeup source #0 1 Module 5 input was a wakeup source #1 MWUF6 Wakeup flag For module 6 6 1 read-only 0 Module 6 input was not a wakeup source #0 1 Module 6 input was a wakeup source #1 MWUF7 Wakeup flag For module 7 7 1 read-only 0 Module 7 input was not a wakeup source #0 1 Module 7 input was a wakeup source #1 FILT1 LLWU Pin Filter 1 register 0x8 8 read-write n 0x0 0x0 FILTE Digital Filter On External Pin 5 2 read-write 00 Filter disabled #00 01 Filter posedge detect enabled #01 10 Filter negedge detect enabled #10 11 Filter any edge detect enabled #11 FILTF Filter Detect Flag 7 1 read-write 0 Pin Filter 1 was not a wakeup source #0 1 Pin Filter 1 was a wakeup source #1 FILTSEL Filter Pin Select 0 4 read-write 0000 Select LLWU_P0 for filter #0000 1111 Select LLWU_P15 for filter #1111 FILT2 LLWU Pin Filter 2 register 0x9 8 read-write n 0x0 0x0 FILTE Digital Filter On External Pin 5 2 read-write 00 Filter disabled #00 01 Filter posedge detect enabled #01 10 Filter negedge detect enabled #10 11 Filter any edge detect enabled #11 FILTF Filter Detect Flag 7 1 read-write 0 Pin Filter 2 was not a wakeup source #0 1 Pin Filter 2 was a wakeup source #1 FILTSEL Filter Pin Select 0 4 read-write 0000 Select LLWU_P0 for filter #0000 1111 Select LLWU_P15 for filter #1111 ME LLWU Module Enable register 0x4 8 read-write n 0x0 0x0 WUME0 Wakeup Module Enable For Module 0 0 1 read-write 0 Internal module flag not used as wakeup source #0 1 Internal module flag used as wakeup source #1 WUME1 Wakeup Module Enable for Module 1 1 1 read-write 0 Internal module flag not used as wakeup source #0 1 Internal module flag used as wakeup source #1 WUME2 Wakeup Module Enable For Module 2 2 1 read-write 0 Internal module flag not used as wakeup source #0 1 Internal module flag used as wakeup source #1 WUME3 Wakeup Module Enable For Module 3 3 1 read-write 0 Internal module flag not used as wakeup source #0 1 Internal module flag used as wakeup source #1 WUME4 Wakeup Module Enable For Module 4 4 1 read-write 0 Internal module flag not used as wakeup source #0 1 Internal module flag used as wakeup source #1 WUME5 Wakeup Module Enable For Module 5 5 1 read-write 0 Internal module flag not used as wakeup source #0 1 Internal module flag used as wakeup source #1 WUME6 Wakeup Module Enable For Module 6 6 1 read-write 0 Internal module flag not used as wakeup source #0 1 Internal module flag used as wakeup source #1 WUME7 Wakeup Module Enable For Module 7 7 1 read-write 0 Internal module flag not used as wakeup source #0 1 Internal module flag used as wakeup source #1 PE1 LLWU Pin Enable 1 register 0x0 8 read-write n 0x0 0x0 WUPE0 Wakeup Pin Enable For LLWU_P0 0 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE1 Wakeup Pin Enable For LLWU_P1 2 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE2 Wakeup Pin Enable For LLWU_P2 4 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE3 Wakeup Pin Enable For LLWU_P3 6 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 PE2 LLWU Pin Enable 2 register 0x1 8 read-write n 0x0 0x0 WUPE4 Wakeup Pin Enable For LLWU_P4 0 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE5 Wakeup Pin Enable For LLWU_P5 2 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE6 Wakeup Pin Enable For LLWU_P6 4 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE7 Wakeup Pin Enable For LLWU_P7 6 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 PE3 LLWU Pin Enable 3 register 0x2 8 read-write n 0x0 0x0 WUPE10 Wakeup Pin Enable For LLWU_P10 4 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE11 Wakeup Pin Enable For LLWU_P11 6 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE8 Wakeup Pin Enable For LLWU_P8 0 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE9 Wakeup Pin Enable For LLWU_P9 2 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 PE4 LLWU Pin Enable 4 register 0x3 8 read-write n 0x0 0x0 WUPE12 Wakeup Pin Enable For LLWU_P12 0 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE13 Wakeup Pin Enable For LLWU_P13 2 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE14 Wakeup Pin Enable For LLWU_P14 4 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 WUPE15 Wakeup Pin Enable For LLWU_P15 6 2 read-write 00 External input pin disabled as wakeup input #00 01 External input pin enabled with rising edge detection #01 10 External input pin enabled with falling edge detection #10 11 External input pin enabled with any change detection #11 LPTMR0 Low Power Timer LPTMR0 0x0 0x0 0x10 registers n LPTMR0 58 CMR Low Power Timer Compare Register 0x8 32 read-write n 0x0 0x0 COMPARE Compare Value 0 16 read-write CNR Low Power Timer Counter Register 0xC 32 read-write n 0x0 0x0 COUNTER Counter Value 0 16 read-write CSR Low Power Timer Control Status Register 0x0 32 read-write n 0x0 0x0 TCF Timer Compare Flag 7 1 read-write 0 The value of CNR is not equal to CMR and increments. #0 1 The value of CNR is equal to CMR and increments. #1 TEN Timer Enable 0 1 read-write 0 LPTMR is disabled and internal logic is reset. #0 1 LPTMR is enabled. #1 TFC Timer Free-Running Counter 2 1 read-write 0 CNR is reset whenever TCF is set. #0 1 CNR is reset on overflow. #1 TIE Timer Interrupt Enable 6 1 read-write 0 Timer interrupt disabled. #0 1 Timer interrupt enabled. #1 TMS Timer Mode Select 1 1 read-write 0 Time Counter mode. #0 1 Pulse Counter mode. #1 TPP Timer Pin Polarity 3 1 read-write 0 Pulse Counter input source is active-high, and the CNR will increment on the rising-edge. #0 1 Pulse Counter input source is active-low, and the CNR will increment on the falling-edge. #1 TPS Timer Pin Select 4 2 read-write 00 Pulse counter input 0 is selected. #00 01 Pulse counter input 1 is selected. #01 10 Pulse counter input 2 is selected. #10 11 Pulse counter input 3 is selected. #11 PSR Low Power Timer Prescale Register 0x4 32 read-write n 0x0 0x0 PBYP Prescaler Bypass 2 1 read-write 0 Prescaler/glitch filter is enabled. #0 1 Prescaler/glitch filter is bypassed. #1 PCS Prescaler Clock Select 0 2 read-write 00 Prescaler/glitch filter clock 0 selected. #00 01 Prescaler/glitch filter clock 1 selected. #01 10 Prescaler/glitch filter clock 2 selected. #10 11 Prescaler/glitch filter clock 3 selected. #11 PRESCALE Prescale Value 3 4 read-write 0000 Prescaler divides the prescaler clock by 2; glitch filter does not support this configuration. #0000 0001 Prescaler divides the prescaler clock by 4; glitch filter recognizes change on input pin after 2 rising clock edges. #0001 0010 Prescaler divides the prescaler clock by 8; glitch filter recognizes change on input pin after 4 rising clock edges. #0010 0011 Prescaler divides the prescaler clock by 16; glitch filter recognizes change on input pin after 8 rising clock edges. #0011 0100 Prescaler divides the prescaler clock by 32; glitch filter recognizes change on input pin after 16 rising clock edges. #0100 0101 Prescaler divides the prescaler clock by 64; glitch filter recognizes change on input pin after 32 rising clock edges. #0101 0110 Prescaler divides the prescaler clock by 128; glitch filter recognizes change on input pin after 64 rising clock edges. #0110 0111 Prescaler divides the prescaler clock by 256; glitch filter recognizes change on input pin after 128 rising clock edges. #0111 1000 Prescaler divides the prescaler clock by 512; glitch filter recognizes change on input pin after 256 rising clock edges. #1000 1001 Prescaler divides the prescaler clock by 1024; glitch filter recognizes change on input pin after 512 rising clock edges. #1001 1010 Prescaler divides the prescaler clock by 2048; glitch filter recognizes change on input pin after 1024 rising clock edges. #1010 1011 Prescaler divides the prescaler clock by 4096; glitch filter recognizes change on input pin after 2048 rising clock edges. #1011 1100 Prescaler divides the prescaler clock by 8192; glitch filter recognizes change on input pin after 4096 rising clock edges. #1100 1101 Prescaler divides the prescaler clock by 16,384; glitch filter recognizes change on input pin after 8192 rising clock edges. #1101 1110 Prescaler divides the prescaler clock by 32,768; glitch filter recognizes change on input pin after 16,384 rising clock edges. #1110 1111 Prescaler divides the prescaler clock by 65,536; glitch filter recognizes change on input pin after 32,768 rising clock edges. #1111 LPUART0 Universal Asynchronous Receiver/Transmitter LPUART0 0x0 0x0 0x18 registers n LPUART0 30 BAUD LPUART Baud Rate Register 0x0 32 read-write n 0x0 0x0 BOTHEDGE Both Edge Sampling 17 1 read-write 0 Receiver samples input data using the rising edge of the baud rate clock. #0 1 Receiver samples input data using the rising and falling edge of the baud rate clock. #1 LBKDIE LIN Break Detect Interrupt Enable 15 1 read-write 0 Hardware interrupts from LPUART_STAT[LBKDIF] disabled (use polling). #0 1 Hardware interrupt requested when LPUART_STAT[LBKDIF] flag is 1. #1 M10 10-bit Mode select 29 1 read-write 0 Receiver and transmitter use 8-bit or 9-bit data characters. #0 1 Receiver and transmitter use 10-bit data characters. #1 MAEN1 Match Address Mode Enable 1 31 1 read-write 0 Normal operation. #0 1 Enables automatic address matching or data matching mode for MATCH[MA1]. #1 MAEN2 Match Address Mode Enable 2 30 1 read-write 0 Normal operation. #0 1 Enables automatic address matching or data matching mode for MATCH[MA2]. #1 MATCFG Match Configuration 18 2 read-write 00 Address Match Wakeup #00 01 Idle Match Wakeup #01 10 Match On and Match Off #10 11 Enables RWU on Data Match and Match On/Off for transmitter CTS input #11 OSR Over Sampling Ratio 24 5 read-write RDMAE Receiver Full DMA Enable 21 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 RESYNCDIS Resynchronization Disable 16 1 read-write 0 Resynchronization during received data word is supported #0 1 Resynchronization during received data word is disabled #1 RXEDGIE RX Input Active Edge Interrupt Enable 14 1 read-write 0 Hardware interrupts from LPUART_STAT[RXEDGIF] disabled (use polling). #0 1 Hardware interrupt requested when LPUART_STAT[RXEDGIF] flag is 1. #1 SBNS Stop Bit Number Select 13 1 read-write 0 One stop bit. #0 1 Two stop bits. #1 SBR Baud Rate Modulo Divisor. 0 13 read-write TDMAE Transmitter DMA Enable 23 1 read-write 0 DMA request disabled. #0 1 DMA request enabled. #1 CTRL LPUART Control Register 0x8 32 read-write n 0x0 0x0 DOZEEN Doze Enable 6 1 read-write 0 LPUART is enabled in Doze mode. #0 1 LPUART is disabled in Doze mode. #1 FEIE Framing Error Interrupt Enable 25 1 read-write 0 FE interrupts disabled; use polling. #0 1 Hardware interrupt requested when FE is set. #1 IDLECFG Idle Configuration 8 3 read-write 000 1 idle character #000 001 2 idle characters #001 010 4 idle characters #010 011 8 idle characters #011 100 16 idle characters #100 101 32 idle characters #101 110 64 idle characters #110 111 128 idle characters #111 ILIE Idle Line Interrupt Enable 20 1 read-write 0 Hardware interrupts from IDLE disabled; use polling. #0 1 Hardware interrupt requested when IDLE flag is 1. #1 ILT Idle Line Type Select 2 1 read-write 0 Idle character bit count starts after start bit. #0 1 Idle character bit count starts after stop bit. #1 LOOPS Loop Mode Select 7 1 read-write 0 Normal operation - LPUART_RX and LPUART_TX use separate pins. #0 1 Loop mode or single-wire mode where transmitter outputs are internally connected to receiver input (see RSRC bit). #1 M 9-Bit or 8-Bit Mode Select 4 1 read-write 0 Receiver and transmitter use 8-bit data characters. #0 1 Receiver and transmitter use 9-bit data characters. #1 MA1IE Match 1 Interrupt Enable 15 1 read-write 0 MA1F interrupt disabled #0 1 MA1F interrupt enabled #1 MA2IE Match 2 Interrupt Enable 14 1 read-write 0 MA2F interrupt disabled #0 1 MA2F interrupt enabled #1 NEIE Noise Error Interrupt Enable 26 1 read-write 0 NF interrupts disabled; use polling. #0 1 Hardware interrupt requested when NF is set. #1 ORIE Overrun Interrupt Enable 27 1 read-write 0 OR interrupts disabled; use polling. #0 1 Hardware interrupt requested when OR is set. #1 PE Parity Enable 1 1 read-write 0 No hardware parity generation or checking. #0 1 Parity enabled. #1 PEIE Parity Error Interrupt Enable 24 1 read-write 0 PF interrupts disabled; use polling). #0 1 Hardware interrupt requested when PF is set. #1 PT Parity Type 0 1 read-write 0 Even parity. #0 1 Odd parity. #1 R8T9 Receive Bit 8 / Transmit Bit 9 31 1 read-write R9T8 Receive Bit 9 / Transmit Bit 8 30 1 read-write RE Receiver Enable 18 1 read-write 0 Receiver disabled. #0 1 Receiver enabled. #1 RIE Receiver Interrupt Enable 21 1 read-write 0 Hardware interrupts from RDRF disabled; use polling. #0 1 Hardware interrupt requested when RDRF flag is 1. #1 RSRC Receiver Source Select 5 1 read-write 0 Provided LOOPS is set, RSRC is cleared, selects internal loop back mode and the LPUART does not use the LPUART_RX pin. #0 1 Single-wire LPUART mode where the LPUART_TX pin is connected to the transmitter output and receiver input. #1 RWU Receiver Wakeup Control 17 1 read-write 0 Normal receiver operation. #0 1 LPUART receiver in standby waiting for wakeup condition. #1 SBK Send Break 16 1 read-write 0 Normal transmitter operation. #0 1 Queue break character(s) to be sent. #1 TCIE Transmission Complete Interrupt Enable for 22 1 read-write 0 Hardware interrupts from TC disabled; use polling. #0 1 Hardware interrupt requested when TC flag is 1. #1 TE Transmitter Enable 19 1 read-write 0 Transmitter disabled. #0 1 Transmitter enabled. #1 TIE Transmit Interrupt Enable 23 1 read-write 0 Hardware interrupts from TDRE disabled; use polling. #0 1 Hardware interrupt requested when TDRE flag is 1. #1 TXDIR LPUART_TX Pin Direction in Single-Wire Mode 29 1 read-write 0 LPUART_TX pin is an input in single-wire mode. #0 1 LPUART_TX pin is an output in single-wire mode. #1 TXINV Transmit Data Inversion 28 1 read-write 0 Transmit data not inverted. #0 1 Transmit data inverted. #1 WAKE Receiver Wakeup Method Select 3 1 read-write 0 Configures RWU for idle-line wakeup. #0 1 Configures RWU with address-mark wakeup. #1 DATA LPUART Data Register 0xC 32 read-write n 0x0 0x0 FRETSC Frame Error / Transmit Special Character 13 1 read-write 0 The dataword was received without a frame error on read, transmit a normal character on write. #0 1 The dataword was received with a frame error, transmit an idle or break character on transmit. #1 IDLINE Idle Line 11 1 read-only 0 Receiver was not idle before receiving this character. #0 1 Receiver was idle before receiving this character. #1 NOISY The current received dataword contained in DATA[R9:R0] was received with noise. 15 1 read-only 0 The dataword was received without noise. #0 1 The data was received with noise. #1 PARITYE The current received dataword contained in DATA[R9:R0] was received with a parity error. 14 1 read-only 0 The dataword was received without a parity error. #0 1 The dataword was received with a parity error. #1 R0T0 Read receive data buffer 0 or write transmit data buffer 0. 0 1 read-write R1T1 Read receive data buffer 1 or write transmit data buffer 1. 1 1 read-write R2T2 Read receive data buffer 2 or write transmit data buffer 2. 2 1 read-write R3T3 Read receive data buffer 3 or write transmit data buffer 3. 3 1 read-write R4T4 Read receive data buffer 4 or write transmit data buffer 4. 4 1 read-write R5T5 Read receive data buffer 5 or write transmit data buffer 5. 5 1 read-write R6T6 Read receive data buffer 6 or write transmit data buffer 6. 6 1 read-write R7T7 Read receive data buffer 7 or write transmit data buffer 7. 7 1 read-write R8T8 Read receive data buffer 8 or write transmit data buffer 8. 8 1 read-write R9T9 Read receive data buffer 9 or write transmit data buffer 9. 9 1 read-write RXEMPT Receive Buffer Empty 12 1 read-only 0 Receive buffer contains valid data. #0 1 Receive buffer is empty, data returned on read is not valid. #1 MATCH LPUART Match Address Register 0x10 32 read-write n 0x0 0x0 MA1 Match Address 1 0 10 read-write MA2 Match Address 2 16 10 read-write MODIR LPUART Modem IrDA Register 0x14 32 read-write n 0x0 0x0 IREN Infrared enable 18 1 read-write 0 IR disabled. #0 1 IR enabled. #1 RXRTSE Receiver request-to-send enable 3 1 read-write 0 The receiver has no effect on RTS. #0 1 RTS is deasserted if the receiver data register is full or a start bit has been detected that would cause the receiver data register to become full. RTS is asserted if the receiver data register is not full and has not detected a start bit that would cause the receiver data register to become full. #1 TNP Transmitter narrow pulse 16 2 read-write 00 1/OSR. #00 01 2/OSR. #01 10 3/OSR. #10 11 4/OSR. #11 TXCTSC Transmit CTS Configuration 4 1 read-write 0 CTS input is sampled at the start of each character. #0 1 CTS input is sampled when the transmitter is idle. #1 TXCTSE Transmitter clear-to-send enable 0 1 read-write 0 CTS has no effect on the transmitter. #0 1 Enables clear-to-send operation. The transmitter checks the state of CTS each time it is ready to send a character. If CTS is asserted, the character is sent. If CTS is deasserted, the signal TXD remains in the mark state and transmission is delayed until CTS is asserted. Changes in CTS as a character is being sent do not affect its transmission. #1 TXCTSSRC Transmit CTS Source 5 1 read-write 0 CTS input is the LPUART_CTS pin. #0 1 CTS input is the inverted Receiver Match result. #1 TXRTSE Transmitter request-to-send enable 1 1 read-write 0 The transmitter has no effect on RTS. #0 1 When a character is placed into an empty transmitter data buffer , RTS asserts one bit time before the start bit is transmitted. RTS deasserts one bit time after all characters in the transmitter data buffer and shift register are completely sent, including the last stop bit. #1 TXRTSPOL Transmitter request-to-send polarity 2 1 read-write 0 Transmitter RTS is active low. #0 1 Transmitter RTS is active high. #1 STAT LPUART Status Register 0x4 32 read-write n 0x0 0x0 BRK13 Break Character Generation Length 26 1 read-write 0 Break character is transmitted with length of 10 bit times (if M = 0, SBNS = 0) or 11 (if M = 1, SBNS = 0 or M = 0, SBNS = 1) or 12 (if M = 1, SBNS = 1 or M10 = 1, SNBS = 0) or 13 (if M10 = 1, SNBS = 1). #0 1 Break character is transmitted with length of 13 bit times (if M = 0, SBNS = 0) or 14 (if M = 1, SBNS = 0 or M = 0, SBNS = 1) or 15 (if M = 1, SBNS = 1 or M10 = 1, SNBS = 0) or 16 (if M10 = 1, SNBS = 1). #1 FE Framing Error Flag 17 1 read-write 0 No framing error detected. This does not guarantee the framing is correct. #0 1 Framing error. #1 IDLE Idle Line Flag 20 1 read-write 0 No idle line detected. #0 1 Idle line was detected. #1 LBKDE LIN Break Detection Enable 25 1 read-write 0 Break character is detected at length 10 bit times (if M = 0, SBNS = 0) or 11 (if M = 1, SBNS = 0 or M = 0, SBNS = 1) or 12 (if M = 1, SBNS = 1 or M10 = 1, SNBS = 0) or 13 (if M10 = 1, SNBS = 1). #0 1 Break character is detected at length of 11 bit times (if M = 0, SBNS = 0) or 12 (if M = 1, SBNS = 0 or M = 0, SBNS = 1) or 14 (if M = 1, SBNS = 1 or M10 = 1, SNBS = 0) or 15 (if M10 = 1, SNBS = 1). #1 LBKDIF LIN Break Detect Interrupt Flag 31 1 read-write 0 No LIN break character has been detected. #0 1 LIN break character has been detected. #1 MA1F Match 1 Flag 15 1 read-write 0 Received data is not equal to MA1 #0 1 Received data is equal to MA1 #1 MA2F Match 2 Flag 14 1 read-write 0 Received data is not equal to MA2 #0 1 Received data is equal to MA2 #1 MSBF MSB First 29 1 read-write 0 LSB (bit0) is the first bit that is transmitted following the start bit. Further, the first bit received after the start bit is identified as bit0. #0 1 MSB (bit9, bit8, bit7 or bit6) is the first bit that is transmitted following the start bit depending on the setting of CTRL[M], CTRL[PE] and BAUD[M10]. Further, the first bit received after the start bit is identified as bit9, bit8, bit7 or bit6 depending on the setting of CTRL[M] and CTRL[PE]. #1 NF Noise Flag 18 1 read-write 0 No noise detected. #0 1 Noise detected in the received character in LPUART_DATA. #1 OR Receiver Overrun Flag 19 1 read-write 0 No overrun. #0 1 Receive overrun (new LPUART data lost). #1 PF Parity Error Flag 16 1 read-write 0 No parity error. #0 1 Parity error. #1 RAF Receiver Active Flag 24 1 read-only 0 LPUART receiver idle waiting for a start bit. #0 1 LPUART receiver active (LPUART_RX input not idle). #1 RDRF Receive Data Register Full Flag 21 1 read-only 0 Receive data buffer empty. #0 1 Receive data buffer full. #1 RWUID Receive Wake Up Idle Detect 27 1 read-write 0 During receive standby state (RWU = 1), the IDLE bit does not get set upon detection of an idle character. During address match wakeup, the IDLE bit does not get set when an address does not match. #0 1 During receive standby state (RWU = 1), the IDLE bit gets set upon detection of an idle character. During address match wakeup, the IDLE bit does get set when an address does not match. #1 RXEDGIF LPUART_RX Pin Active Edge Interrupt Flag 30 1 read-write 0 No active edge on the receive pin has occurred. #0 1 An active edge on the receive pin has occurred. #1 RXINV Receive Data Inversion 28 1 read-write 0 Receive data not inverted. #0 1 Receive data inverted. #1 TC Transmission Complete Flag 22 1 read-only 0 Transmitter active (sending data, a preamble, or a break). #0 1 Transmitter idle (transmission activity complete). #1 TDRE Transmit Data Register Empty Flag 23 1 read-only 0 Transmit data buffer full. #0 1 Transmit data buffer empty. #1 MCG Multipurpose Clock Generator module MCG 0x0 0x0 0xE registers n ATCVH MCG Auto Trim Compare Value High Register 0xA 8 read-write n 0x0 0x0 ATCVH ATM Compare Value High 0 8 read-write ATCVL MCG Auto Trim Compare Value Low Register 0xB 8 read-write n 0x0 0x0 ATCVL ATM Compare Value Low 0 8 read-write C1 MCG Control 1 Register 0x0 8 read-write n 0x0 0x0 CLKS Clock Source Select 6 2 read-write 00 Encoding 0 - Output of FLL or PLL is selected (depends on PLLS control bit). #00 01 Encoding 1 - Internal reference clock is selected. #01 10 Encoding 2 - External reference clock is selected. #10 11 Encoding 3 - Reserved. #11 FRDIV FLL External Reference Divider 3 3 read-write 000 If RANGE = 0 or OSCSEL=1 , Divide Factor is 1; for all other RANGE values, Divide Factor is 32. #000 001 If RANGE = 0 or OSCSEL=1 , Divide Factor is 2; for all other RANGE values, Divide Factor is 64. #001 010 If RANGE = 0 or OSCSEL=1 , Divide Factor is 4; for all other RANGE values, Divide Factor is 128. #010 011 If RANGE = 0 or OSCSEL=1 , Divide Factor is 8; for all other RANGE values, Divide Factor is 256. #011 100 If RANGE = 0 or OSCSEL=1 , Divide Factor is 16; for all other RANGE values, Divide Factor is 512. #100 101 If RANGE = 0 or OSCSEL=1 , Divide Factor is 32; for all other RANGE values, Divide Factor is 1024. #101 110 If RANGE = 0 or OSCSEL=1 , Divide Factor is 64; for all other RANGE values, Divide Factor is 1280 . #110 111 If RANGE = 0 or OSCSEL=1 , Divide Factor is 128; for all other RANGE values, Divide Factor is 1536 . #111 IRCLKEN Internal Reference Clock Enable 1 1 read-write 0 MCGIRCLK inactive. #0 1 MCGIRCLK active. #1 IREFS Internal Reference Select 2 1 read-write 0 External reference clock is selected. #0 1 The slow internal reference clock is selected. #1 IREFSTEN Internal Reference Stop Enable 0 1 read-write 0 Internal reference clock is disabled in Stop mode. #0 1 Internal reference clock is enabled in Stop mode if IRCLKEN is set or if MCG is in FEI, FBI, or BLPI modes before entering Stop mode. #1 C2 MCG Control 2 Register 0x1 8 read-write n 0x0 0x0 EREFS External Reference Select 2 1 read-write 0 External reference clock requested. #0 1 Oscillator requested. #1 FCFTRIM Fast Internal Reference Clock Fine Trim 6 1 read-write HGO High Gain Oscillator Select 3 1 read-write 0 Configure crystal oscillator for low-power operation. #0 1 Configure crystal oscillator for high-gain operation. #1 IRCS Internal Reference Clock Select 0 1 read-write 0 Slow internal reference clock selected. #0 1 Fast internal reference clock selected. #1 LOCRE0 Loss of Clock Reset Enable 7 1 read-write 0 Interrupt request is generated on a loss of OSC0 external reference clock. #0 1 Generate a reset request on a loss of OSC0 external reference clock. #1 LP Low Power Select 1 1 read-write 0 FLL or PLL is not disabled in bypass modes. #0 1 FLL or PLL is disabled in bypass modes (lower power) #1 RANGE Frequency Range Select 4 2 read-write 00 Encoding 0 - Low frequency range selected for the crystal oscillator . #00 01 Encoding 1 - High frequency range selected for the crystal oscillator . #01 C3 MCG Control 3 Register 0x2 8 read-write n 0x0 0x0 SCTRIM Slow Internal Reference Clock Trim Setting 0 8 read-write C4 MCG Control 4 Register 0x3 8 read-write n 0x0 0x0 DMX32 DCO Maximum Frequency with 32.768 kHz Reference 7 1 read-write 0 DCO has a default range of 25%. #0 1 DCO is fine-tuned for maximum frequency with 32.768 kHz reference. #1 DRST_DRS DCO Range Select 5 2 read-write 00 Encoding 0 - Low range (reset default). #00 01 Encoding 1 - Mid range. #01 10 Encoding 2 - Mid-high range. #10 11 Encoding 3 - High range. #11 FCTRIM Fast Internal Reference Clock Trim Setting 1 4 read-write SCFTRIM Slow Internal Reference Clock Fine Trim 0 1 read-write C5 MCG Control 5 Register 0x4 8 read-write n 0x0 0x0 PLLCLKEN0 PLL Clock Enable 6 1 read-write 0 MCGPLLCLK is inactive. #0 1 MCGPLLCLK is active. #1 PLLSTEN0 PLL Stop Enable 5 1 read-write 0 MCGPLLCLK is disabled in any of the Stop modes. #0 1 MCGPLLCLK is enabled if system is in Normal Stop mode. #1 PRDIV0 PLL External Reference Divider 0 5 read-write 0 Divide Factor is 1 #00000 1 Divide Factor is 2 #00001 2 Divide Factor is 3 #00010 3 Divide Factor is 4 #00011 4 Divide Factor is 5 #00100 5 Divide Factor is 6 #00101 6 Divide Factor is 7 #00110 7 Divide Factor is 8 #00111 8 Divide Factor is 9 #01000 9 Divide Factor is 10 #01001 10 Divide Factor is 11 #01010 11 Divide Factor is 12 #01011 12 Divide Factor is 13 #01100 13 Divide Factor is 14 #01101 14 Divide Factor is 15 #01110 15 Divide Factor is 16 #01111 16 Divide Factor is 17 #10000 17 Divide Factor is 18 #10001 18 Divide Factor is 19 #10010 19 Divide Factor is 20 #10011 20 Divide Factor is 21 #10100 21 Divide Factor is 22 #10101 22 Divide Factor is 23 #10110 23 Divide Factor is 24 #10111 24 Divide Factor is 25 #11000 25 Divide Factor is 26 #11001 26 Divide Factor is 27 #11010 27 Divide Factor is 28 #11011 28 Divide Factor is 29 #11100 29 Divide Factor is 30 #11101 30 Divide Factor is 31 #11110 31 Divide Factor is 32 #11111 C6 MCG Control 6 Register 0x5 8 read-write n 0x0 0x0 CME0 Clock Monitor Enable 5 1 read-write 0 External clock monitor is disabled for OSC0. #0 1 External clock monitor is enabled for OSC0. #1 LOLIE0 Loss of Lock Interrrupt Enable 7 1 read-write 0 No interrupt request is generated on loss of lock. #0 1 Generate an interrupt request on loss of lock. #1 PLLS PLL Select 6 1 read-write 0 FLL is selected. #0 1 PLL is selected (PRDIV 0 need to be programmed to the correct divider to generate a PLL reference clock in the range of 2-4 MHz prior to setting the PLLS bit). #1 VDIV0 VCO 0 Divider 0 5 read-write 0 Multiply Factor is 24 #00000 1 Multiply Factor is 25 #00001 2 Multiply Factor is 26 #00010 3 Multiply Factor is 27 #00011 4 Multiply Factor is 28 #00100 5 Multiply Factor is 29 #00101 6 Multiply Factor is 30 #00110 7 Multiply Factor is 31 #00111 8 Multiply Factor is 32 #01000 9 Multiply Factor is 33 #01001 10 Multiply Factor is 34 #01010 11 Multiply Factor is 35 #01011 12 Multiply Factor is 36 #01100 13 Multiply Factor is 37 #01101 14 Multiply Factor is 38 #01110 15 Multiply Factor is 39 #01111 16 Multiply Factor is 40 #10000 17 Multiply Factor is 41 #10001 18 Multiply Factor is 42 #10010 19 Multiply Factor is 43 #10011 20 Multiply Factor is 44 #10100 21 Multiply Factor is 45 #10101 22 Multiply Factor is 46 #10110 23 Multiply Factor is 47 #10111 24 Multiply Factor is 48 #11000 25 Multiply Factor is 49 #11001 26 Multiply Factor is 50 #11010 27 Multiply Factor is 51 #11011 28 Multiply Factor is 52 #11100 29 Multiply Factor is 53 #11101 30 Multiply Factor is 54 #11110 31 Multiply Factor is 55 #11111 C7 MCG Control 7 Register 0xC 8 read-write n 0x0 0x0 OSCSEL MCG OSC Clock Select 0 2 read-write 00 Selects Oscillator (OSCCLK0). #00 01 Selects 32 kHz RTC Oscillator. #01 10 Selects Oscillator (OSCCLK1). #10 C8 MCG Control 8 Register 0xD 8 read-write n 0x0 0x0 CME1 Clock Monitor Enable1 5 1 read-write 0 External clock monitor is disabled for RTC clock. #0 1 External clock monitor is enabled for RTC clock. #1 LOCRE1 Loss of Clock Reset Enable 7 1 read-write 0 Interrupt request is generated on a loss of RTC external reference clock. #0 1 Generate a reset request on a loss of RTC external reference clock #1 LOCS1 RTC Loss of Clock Status 0 1 read-write 0 Loss of RTC has not occur. #0 1 Loss of RTC has occur #1 LOLRE PLL Loss of Lock Reset Enable 6 1 read-write 0 Interrupt request is generated on a PLL loss of lock indication. The PLL loss of lock interrupt enable bit must also be set to generate the interrupt request. #0 1 Generate a reset request on a PLL loss of lock indication. #1 S MCG Status Register 0x6 8 read-write n 0x0 0x0 CLKST Clock Mode Status 2 2 read-only 00 Encoding 0 - Output of the FLL is selected (reset default). #00 01 Encoding 1 - Internal reference clock is selected. #01 10 Encoding 2 - External reference clock is selected. #10 11 Encoding 3 - Output of the PLL is selected. #11 IRCST Internal Reference Clock Status 0 1 read-only 0 Source of internal reference clock is the slow clock (32 kHz IRC). #0 1 Source of internal reference clock is the fast clock (4 MHz IRC). #1 IREFST Internal Reference Status 4 1 read-only 0 Source of FLL reference clock is the external reference clock. #0 1 Source of FLL reference clock is the internal reference clock. #1 LOCK0 Lock Status 6 1 read-only 0 PLL is currently unlocked. #0 1 PLL is currently locked. #1 LOLS0 Loss of Lock Status 7 1 read-write 0 PLL has not lost lock since LOLS 0 was last cleared. #0 1 PLL has lost lock since LOLS 0 was last cleared. #1 OSCINIT0 OSC Initialization 1 1 read-only PLLST PLL Select Status 5 1 read-only 0 Source of PLLS clock is FLL clock. #0 1 Source of PLLS clock is PLL output clock. #1 SC MCG Status and Control Register 0x8 8 read-write n 0x0 0x0 ATME Automatic Trim Machine Enable 7 1 read-write 0 Auto Trim Machine disabled. #0 1 Auto Trim Machine enabled. #1 ATMF Automatic Trim Machine Fail Flag 5 1 read-write 0 Automatic Trim Machine completed normally. #0 1 Automatic Trim Machine failed. #1 ATMS Automatic Trim Machine Select 6 1 read-write 0 32 kHz Internal Reference Clock selected. #0 1 4 MHz Internal Reference Clock selected. #1 FCRDIV Fast Clock Internal Reference Divider 1 3 read-write 000 Divide Factor is 1 #000 001 Divide Factor is 2. #001 010 Divide Factor is 4. #010 011 Divide Factor is 8. #011 100 Divide Factor is 16 #100 101 Divide Factor is 32 #101 110 Divide Factor is 64 #110 111 Divide Factor is 128. #111 FLTPRSRV FLL Filter Preserve Enable 4 1 read-write 0 FLL filter and FLL frequency will reset on changes to currect clock mode. #0 1 Fll filter and FLL frequency retain their previous values during new clock mode change. #1 LOCS0 OSC0 Loss of Clock Status 0 1 read-write 0 Loss of OSC0 has not occurred. #0 1 Loss of OSC0 has occurred. #1 MCM Core Platform Miscellaneous Control Module MCM 0x0 0x8 0x3C registers n MCM 17 CPO Compute Operation Control Register 0x40 32 read-write n 0x0 0x0 CPOACK Compute Operation acknowledge 1 1 read-only 0 Compute operation entry has not completed or compute operation exit has completed. #0 1 Compute operation entry has completed or compute operation exit has not completed. #1 CPOREQ Compute Operation request 0 1 read-write 0 Request is cleared. #0 1 Request Compute Operation. #1 CPOWOI Compute Operation wakeup on interrupt 2 1 read-write 0 No effect. #0 1 When set, the CPOREQ is cleared on any interrupt or exception vector fetch. #1 ISCR Interrupt Status and Control Register 0x10 32 read-write n 0x0 0x0 FDZC FPU divide-by-zero interrupt status 9 1 read-only 0 No interrupt #0 1 Interrupt occurred #1 FDZCE FPU divide-by-zero interrupt enable 25 1 read-write 0 Disable interrupt #0 1 Enable interrupt #1 FIDC FPU input denormal interrupt status 15 1 read-only 0 No interrupt #0 1 Interrupt occurred #1 FIDCE FPU input denormal interrupt enable 31 1 read-write 0 Disable interrupt #0 1 Enable interrupt #1 FIOC FPU invalid operation interrupt status 8 1 read-only 0 No interrupt #0 1 Interrupt occurred #1 FIOCE FPU invalid operation interrupt enable 24 1 read-write 0 Disable interrupt #0 1 Enable interrupt #1 FIXC FPU inexact interrupt status 12 1 read-only 0 No interrupt #0 1 Interrupt occurred #1 FIXCE FPU inexact interrupt enable 28 1 read-write 0 Disable interrupt #0 1 Enable interrupt #1 FOFC FPU overflow interrupt status 10 1 read-only 0 No interrupt #0 1 Interrupt occurred #1 FOFCE FPU overflow interrupt enable 26 1 read-write 0 Disable interrupt #0 1 Enable interrupt #1 FUFC FPU underflow interrupt status 11 1 read-only 0 No interrupt #0 1 Interrupt occurred #1 FUFCE FPU underflow interrupt enable 27 1 read-write 0 Disable interrupt #0 1 Enable interrupt #1 PLACR Crossbar Switch (AXBS) Control Register 0xC 32 read-write n 0x0 0x0 ARB Arbitration select 9 1 read-write 0 Fixed-priority arbitration for the crossbar masters #0 1 Round-robin arbitration for the crossbar masters #1 PLAMC Crossbar Switch (AXBS) Master Configuration 0xA 16 read-only n 0x0 0x0 AMC Each bit in the AMC field indicates whether there is a corresponding connection to the AXBS master input port. 0 8 read-only 0 A bus master connection to AXBS input port n is absent #0 1 A bus master connection to AXBS input port n is present #1 PLASC Crossbar Switch (AXBS) Slave Configuration 0x8 16 read-only n 0x0 0x0 ASC Each bit in the ASC field indicates whether there is a corresponding connection to the crossbar switch's slave input port. 0 8 read-only 0 A bus slave connection to AXBS input port n is absent #0 1 A bus slave connection to AXBS input port n is present #1 NVIC Nested Vectored Interrupt Controller NVIC 0x0 0x0 0xE04 registers n NVICIABR0 Interrupt Active bit Register n 0x200 32 read-write n 0x0 0x0 ACTIVE Interrupt active flags 0 32 read-write NVICIABR1 Interrupt Active bit Register n 0x204 32 read-write n 0x0 0x0 ACTIVE Interrupt active flags 0 32 read-write NVICIABR2 Interrupt Active bit Register n 0x208 32 read-write n 0x0 0x0 ACTIVE Interrupt active flags 0 32 read-write NVICIABR3 Interrupt Active bit Register n 0x20C 32 read-write n 0x0 0x0 ACTIVE Interrupt active flags 0 32 read-write NVICICER0 Interrupt Clear Enable Register n 0x80 32 read-write n 0x0 0x0 CLRENA Interrupt clear-enable bits 0 32 read-write NVICICER1 Interrupt Clear Enable Register n 0x84 32 read-write n 0x0 0x0 CLRENA Interrupt clear-enable bits 0 32 read-write NVICICER2 Interrupt Clear Enable Register n 0x88 32 read-write n 0x0 0x0 CLRENA Interrupt clear-enable bits 0 32 read-write NVICICER3 Interrupt Clear Enable Register n 0x8C 32 read-write n 0x0 0x0 CLRENA Interrupt clear-enable bits 0 32 read-write NVICICPR0 Interrupt Clear Pending Register n 0x180 32 read-write n 0x0 0x0 CLRPEND Interrupt clear-pending bits 0 32 read-write NVICICPR1 Interrupt Clear Pending Register n 0x184 32 read-write n 0x0 0x0 CLRPEND Interrupt clear-pending bits 0 32 read-write NVICICPR2 Interrupt Clear Pending Register n 0x188 32 read-write n 0x0 0x0 CLRPEND Interrupt clear-pending bits 0 32 read-write NVICICPR3 Interrupt Clear Pending Register n 0x18C 32 read-write n 0x0 0x0 CLRPEND Interrupt clear-pending bits 0 32 read-write NVICIP0 Interrupt Priority Register n 0x300 8 read-write n 0x0 0x0 PRI0 Priority of interrupt 0 0 8 read-write NVICIP1 Interrupt Priority Register n 0x301 8 read-write n 0x0 0x0 PRI1 Priority of interrupt 1 0 8 read-write NVICIP10 Interrupt Priority Register n 0x30A 8 read-write n 0x0 0x0 PRI10 Priority of interrupt 10 0 8 read-write NVICIP100 Interrupt Priority Register n 0x364 8 read-write n 0x0 0x0 PRI100 Priority of interrupt 100 0 8 read-write NVICIP101 Interrupt Priority Register n 0x365 8 read-write n 0x0 0x0 PRI101 Priority of interrupt 101 0 8 read-write NVICIP102 Interrupt Priority Register n 0x366 8 read-write n 0x0 0x0 PRI102 Priority of interrupt 102 0 8 read-write NVICIP103 Interrupt Priority Register n 0x367 8 read-write n 0x0 0x0 PRI103 Priority of interrupt 103 0 8 read-write NVICIP104 Interrupt Priority Register n 0x368 8 read-write n 0x0 0x0 PRI104 Priority of interrupt 104 0 8 read-write NVICIP105 Interrupt Priority Register n 0x369 8 read-write n 0x0 0x0 PRI105 Priority of interrupt 105 0 8 read-write NVICIP11 Interrupt Priority Register n 0x30B 8 read-write n 0x0 0x0 PRI11 Priority of interrupt 11 0 8 read-write NVICIP12 Interrupt Priority Register n 0x30C 8 read-write n 0x0 0x0 PRI12 Priority of interrupt 12 0 8 read-write NVICIP13 Interrupt Priority Register n 0x30D 8 read-write n 0x0 0x0 PRI13 Priority of interrupt 13 0 8 read-write NVICIP14 Interrupt Priority Register n 0x30E 8 read-write n 0x0 0x0 PRI14 Priority of interrupt 14 0 8 read-write NVICIP15 Interrupt Priority Register n 0x30F 8 read-write n 0x0 0x0 PRI15 Priority of interrupt 15 0 8 read-write NVICIP16 Interrupt Priority Register n 0x310 8 read-write n 0x0 0x0 PRI16 Priority of interrupt 16 0 8 read-write NVICIP17 Interrupt Priority Register n 0x311 8 read-write n 0x0 0x0 PRI17 Priority of interrupt 17 0 8 read-write NVICIP18 Interrupt Priority Register n 0x312 8 read-write n 0x0 0x0 PRI18 Priority of interrupt 18 0 8 read-write NVICIP19 Interrupt Priority Register n 0x313 8 read-write n 0x0 0x0 PRI19 Priority of interrupt 19 0 8 read-write NVICIP2 Interrupt Priority Register n 0x302 8 read-write n 0x0 0x0 PRI2 Priority of interrupt 2 0 8 read-write NVICIP20 Interrupt Priority Register n 0x314 8 read-write n 0x0 0x0 PRI20 Priority of interrupt 20 0 8 read-write NVICIP21 Interrupt Priority Register n 0x315 8 read-write n 0x0 0x0 PRI21 Priority of interrupt 21 0 8 read-write NVICIP22 Interrupt Priority Register n 0x316 8 read-write n 0x0 0x0 PRI22 Priority of interrupt 22 0 8 read-write NVICIP23 Interrupt Priority Register n 0x317 8 read-write n 0x0 0x0 PRI23 Priority of interrupt 23 0 8 read-write NVICIP24 Interrupt Priority Register n 0x318 8 read-write n 0x0 0x0 PRI24 Priority of interrupt 24 0 8 read-write NVICIP25 Interrupt Priority Register n 0x319 8 read-write n 0x0 0x0 PRI25 Priority of interrupt 25 0 8 read-write NVICIP26 Interrupt Priority Register n 0x31A 8 read-write n 0x0 0x0 PRI26 Priority of interrupt 26 0 8 read-write NVICIP27 Interrupt Priority Register n 0x31B 8 read-write n 0x0 0x0 PRI27 Priority of interrupt 27 0 8 read-write NVICIP28 Interrupt Priority Register n 0x31C 8 read-write n 0x0 0x0 PRI28 Priority of interrupt 28 0 8 read-write NVICIP29 Interrupt Priority Register n 0x31D 8 read-write n 0x0 0x0 PRI29 Priority of interrupt 29 0 8 read-write NVICIP3 Interrupt Priority Register n 0x303 8 read-write n 0x0 0x0 PRI3 Priority of interrupt 3 0 8 read-write NVICIP30 Interrupt Priority Register n 0x31E 8 read-write n 0x0 0x0 PRI30 Priority of interrupt 30 0 8 read-write NVICIP31 Interrupt Priority Register n 0x31F 8 read-write n 0x0 0x0 PRI31 Priority of interrupt 31 0 8 read-write NVICIP32 Interrupt Priority Register n 0x320 8 read-write n 0x0 0x0 PRI32 Priority of interrupt 32 0 8 read-write NVICIP33 Interrupt Priority Register n 0x321 8 read-write n 0x0 0x0 PRI33 Priority of interrupt 33 0 8 read-write NVICIP34 Interrupt Priority Register n 0x322 8 read-write n 0x0 0x0 PRI34 Priority of interrupt 34 0 8 read-write NVICIP35 Interrupt Priority Register n 0x323 8 read-write n 0x0 0x0 PRI35 Priority of interrupt 35 0 8 read-write NVICIP36 Interrupt Priority Register n 0x324 8 read-write n 0x0 0x0 PRI36 Priority of interrupt 36 0 8 read-write NVICIP37 Interrupt Priority Register n 0x325 8 read-write n 0x0 0x0 PRI37 Priority of interrupt 37 0 8 read-write NVICIP38 Interrupt Priority Register n 0x326 8 read-write n 0x0 0x0 PRI38 Priority of interrupt 38 0 8 read-write NVICIP39 Interrupt Priority Register n 0x327 8 read-write n 0x0 0x0 PRI39 Priority of interrupt 39 0 8 read-write NVICIP4 Interrupt Priority Register n 0x304 8 read-write n 0x0 0x0 PRI4 Priority of interrupt 4 0 8 read-write NVICIP40 Interrupt Priority Register n 0x328 8 read-write n 0x0 0x0 PRI40 Priority of interrupt 40 0 8 read-write NVICIP41 Interrupt Priority Register n 0x329 8 read-write n 0x0 0x0 PRI41 Priority of interrupt 41 0 8 read-write NVICIP42 Interrupt Priority Register n 0x32A 8 read-write n 0x0 0x0 PRI42 Priority of interrupt 42 0 8 read-write NVICIP43 Interrupt Priority Register n 0x32B 8 read-write n 0x0 0x0 PRI43 Priority of interrupt 43 0 8 read-write NVICIP44 Interrupt Priority Register n 0x32C 8 read-write n 0x0 0x0 PRI44 Priority of interrupt 44 0 8 read-write NVICIP45 Interrupt Priority Register n 0x32D 8 read-write n 0x0 0x0 PRI45 Priority of interrupt 45 0 8 read-write NVICIP46 Interrupt Priority Register n 0x32E 8 read-write n 0x0 0x0 PRI46 Priority of interrupt 46 0 8 read-write NVICIP47 Interrupt Priority Register n 0x32F 8 read-write n 0x0 0x0 PRI47 Priority of interrupt 47 0 8 read-write NVICIP48 Interrupt Priority Register n 0x330 8 read-write n 0x0 0x0 PRI48 Priority of interrupt 48 0 8 read-write NVICIP49 Interrupt Priority Register n 0x331 8 read-write n 0x0 0x0 PRI49 Priority of interrupt 49 0 8 read-write NVICIP5 Interrupt Priority Register n 0x305 8 read-write n 0x0 0x0 PRI5 Priority of interrupt 5 0 8 read-write NVICIP50 Interrupt Priority Register n 0x332 8 read-write n 0x0 0x0 PRI50 Priority of interrupt 50 0 8 read-write NVICIP51 Interrupt Priority Register n 0x333 8 read-write n 0x0 0x0 PRI51 Priority of interrupt 51 0 8 read-write NVICIP52 Interrupt Priority Register n 0x334 8 read-write n 0x0 0x0 PRI52 Priority of interrupt 52 0 8 read-write NVICIP53 Interrupt Priority Register n 0x335 8 read-write n 0x0 0x0 PRI53 Priority of interrupt 53 0 8 read-write NVICIP54 Interrupt Priority Register n 0x336 8 read-write n 0x0 0x0 PRI54 Priority of interrupt 54 0 8 read-write NVICIP55 Interrupt Priority Register n 0x337 8 read-write n 0x0 0x0 PRI55 Priority of interrupt 55 0 8 read-write NVICIP56 Interrupt Priority Register n 0x338 8 read-write n 0x0 0x0 PRI56 Priority of interrupt 56 0 8 read-write NVICIP57 Interrupt Priority Register n 0x339 8 read-write n 0x0 0x0 PRI57 Priority of interrupt 57 0 8 read-write NVICIP58 Interrupt Priority Register n 0x33A 8 read-write n 0x0 0x0 PRI58 Priority of interrupt 58 0 8 read-write NVICIP59 Interrupt Priority Register n 0x33B 8 read-write n 0x0 0x0 PRI59 Priority of interrupt 59 0 8 read-write NVICIP6 Interrupt Priority Register n 0x306 8 read-write n 0x0 0x0 PRI6 Priority of interrupt 6 0 8 read-write NVICIP60 Interrupt Priority Register n 0x33C 8 read-write n 0x0 0x0 PRI60 Priority of interrupt 60 0 8 read-write NVICIP61 Interrupt Priority Register n 0x33D 8 read-write n 0x0 0x0 PRI61 Priority of interrupt 61 0 8 read-write NVICIP62 Interrupt Priority Register n 0x33E 8 read-write n 0x0 0x0 PRI62 Priority of interrupt 62 0 8 read-write NVICIP63 Interrupt Priority Register n 0x33F 8 read-write n 0x0 0x0 PRI63 Priority of interrupt 63 0 8 read-write NVICIP64 Interrupt Priority Register n 0x340 8 read-write n 0x0 0x0 PRI64 Priority of interrupt 64 0 8 read-write NVICIP65 Interrupt Priority Register n 0x341 8 read-write n 0x0 0x0 PRI65 Priority of interrupt 65 0 8 read-write NVICIP66 Interrupt Priority Register n 0x342 8 read-write n 0x0 0x0 PRI66 Priority of interrupt 66 0 8 read-write NVICIP67 Interrupt Priority Register n 0x343 8 read-write n 0x0 0x0 PRI67 Priority of interrupt 67 0 8 read-write NVICIP68 Interrupt Priority Register n 0x344 8 read-write n 0x0 0x0 PRI68 Priority of interrupt 68 0 8 read-write NVICIP69 Interrupt Priority Register n 0x345 8 read-write n 0x0 0x0 PRI69 Priority of interrupt 69 0 8 read-write NVICIP7 Interrupt Priority Register n 0x307 8 read-write n 0x0 0x0 PRI7 Priority of interrupt 7 0 8 read-write NVICIP70 Interrupt Priority Register n 0x346 8 read-write n 0x0 0x0 PRI70 Priority of interrupt 70 0 8 read-write NVICIP71 Interrupt Priority Register n 0x347 8 read-write n 0x0 0x0 PRI71 Priority of interrupt 71 0 8 read-write NVICIP72 Interrupt Priority Register n 0x348 8 read-write n 0x0 0x0 PRI72 Priority of interrupt 72 0 8 read-write NVICIP73 Interrupt Priority Register n 0x349 8 read-write n 0x0 0x0 PRI73 Priority of interrupt 73 0 8 read-write NVICIP74 Interrupt Priority Register n 0x34A 8 read-write n 0x0 0x0 PRI74 Priority of interrupt 74 0 8 read-write NVICIP75 Interrupt Priority Register n 0x34B 8 read-write n 0x0 0x0 PRI75 Priority of interrupt 75 0 8 read-write NVICIP76 Interrupt Priority Register n 0x34C 8 read-write n 0x0 0x0 PRI76 Priority of interrupt 76 0 8 read-write NVICIP77 Interrupt Priority Register n 0x34D 8 read-write n 0x0 0x0 PRI77 Priority of interrupt 77 0 8 read-write NVICIP78 Interrupt Priority Register n 0x34E 8 read-write n 0x0 0x0 PRI78 Priority of interrupt 78 0 8 read-write NVICIP79 Interrupt Priority Register n 0x34F 8 read-write n 0x0 0x0 PRI79 Priority of interrupt 79 0 8 read-write NVICIP8 Interrupt Priority Register n 0x308 8 read-write n 0x0 0x0 PRI8 Priority of interrupt 8 0 8 read-write NVICIP80 Interrupt Priority Register n 0x350 8 read-write n 0x0 0x0 PRI80 Priority of interrupt 80 0 8 read-write NVICIP81 Interrupt Priority Register n 0x351 8 read-write n 0x0 0x0 PRI81 Priority of interrupt 81 0 8 read-write NVICIP82 Interrupt Priority Register n 0x352 8 read-write n 0x0 0x0 PRI82 Priority of interrupt 82 0 8 read-write NVICIP83 Interrupt Priority Register n 0x353 8 read-write n 0x0 0x0 PRI83 Priority of interrupt 83 0 8 read-write NVICIP84 Interrupt Priority Register n 0x354 8 read-write n 0x0 0x0 PRI84 Priority of interrupt 84 0 8 read-write NVICIP85 Interrupt Priority Register n 0x355 8 read-write n 0x0 0x0 PRI85 Priority of interrupt 85 0 8 read-write NVICIP86 Interrupt Priority Register n 0x356 8 read-write n 0x0 0x0 PRI86 Priority of interrupt 86 0 8 read-write NVICIP87 Interrupt Priority Register n 0x357 8 read-write n 0x0 0x0 PRI87 Priority of interrupt 87 0 8 read-write NVICIP88 Interrupt Priority Register n 0x358 8 read-write n 0x0 0x0 PRI88 Priority of interrupt 88 0 8 read-write NVICIP89 Interrupt Priority Register n 0x359 8 read-write n 0x0 0x0 PRI89 Priority of interrupt 89 0 8 read-write NVICIP9 Interrupt Priority Register n 0x309 8 read-write n 0x0 0x0 PRI9 Priority of interrupt 9 0 8 read-write NVICIP90 Interrupt Priority Register n 0x35A 8 read-write n 0x0 0x0 PRI90 Priority of interrupt 90 0 8 read-write NVICIP91 Interrupt Priority Register n 0x35B 8 read-write n 0x0 0x0 PRI91 Priority of interrupt 91 0 8 read-write NVICIP92 Interrupt Priority Register n 0x35C 8 read-write n 0x0 0x0 PRI92 Priority of interrupt 92 0 8 read-write NVICIP93 Interrupt Priority Register n 0x35D 8 read-write n 0x0 0x0 PRI93 Priority of interrupt 93 0 8 read-write NVICIP94 Interrupt Priority Register n 0x35E 8 read-write n 0x0 0x0 PRI94 Priority of interrupt 94 0 8 read-write NVICIP95 Interrupt Priority Register n 0x35F 8 read-write n 0x0 0x0 PRI95 Priority of interrupt 95 0 8 read-write NVICIP96 Interrupt Priority Register n 0x360 8 read-write n 0x0 0x0 PRI96 Priority of interrupt 96 0 8 read-write NVICIP97 Interrupt Priority Register n 0x361 8 read-write n 0x0 0x0 PRI97 Priority of interrupt 97 0 8 read-write NVICIP98 Interrupt Priority Register n 0x362 8 read-write n 0x0 0x0 PRI98 Priority of interrupt 98 0 8 read-write NVICIP99 Interrupt Priority Register n 0x363 8 read-write n 0x0 0x0 PRI99 Priority of interrupt 99 0 8 read-write NVICISER0 Interrupt Set Enable Register n 0x0 32 read-write n 0x0 0x0 SETENA Interrupt set enable bits 0 32 read-write NVICISER1 Interrupt Set Enable Register n 0x4 32 read-write n 0x0 0x0 SETENA Interrupt set enable bits 0 32 read-write NVICISER2 Interrupt Set Enable Register n 0x8 32 read-write n 0x0 0x0 SETENA Interrupt set enable bits 0 32 read-write NVICISER3 Interrupt Set Enable Register n 0xC 32 read-write n 0x0 0x0 SETENA Interrupt set enable bits 0 32 read-write NVICISPR0 Interrupt Set Pending Register n 0x100 32 read-write n 0x0 0x0 SETPEND Interrupt set-pending bits 0 32 read-write NVICISPR1 Interrupt Set Pending Register n 0x104 32 read-write n 0x0 0x0 SETPEND Interrupt set-pending bits 0 32 read-write NVICISPR2 Interrupt Set Pending Register n 0x108 32 read-write n 0x0 0x0 SETPEND Interrupt set-pending bits 0 32 read-write NVICISPR3 Interrupt Set Pending Register n 0x10C 32 read-write n 0x0 0x0 SETPEND Interrupt set-pending bits 0 32 read-write NVICSTIR Software Trigger Interrupt Register 0xE00 32 read-write n 0x0 0x0 INTID Interrupt ID of the interrupt to trigger, in the range 0-239. For example, a value of 0x03 specifies interrupt IRQ3. 0 9 read-write OSC Oscillator OSC 0x0 0x0 0x3 registers n CR OSC Control Register 0x0 8 read-write n 0x0 0x0 ERCLKEN External Reference Enable 7 1 read-write 0 External reference clock is inactive. #0 1 External reference clock is enabled. #1 EREFSTEN External Reference Stop Enable 5 1 read-write 0 External reference clock is disabled in Stop mode. #0 1 External reference clock stays enabled in Stop mode if ERCLKEN is set before entering Stop mode. #1 SC16P Oscillator 16 pF Capacitor Load Configure 0 1 read-write 0 Disable the selection. #0 1 Add 16 pF capacitor to the oscillator load. #1 SC2P Oscillator 2 pF Capacitor Load Configure 3 1 read-write 0 Disable the selection. #0 1 Add 2 pF capacitor to the oscillator load. #1 SC4P Oscillator 4 pF Capacitor Load Configure 2 1 read-write 0 Disable the selection. #0 1 Add 4 pF capacitor to the oscillator load. #1 SC8P Oscillator 8 pF Capacitor Load Configure 1 1 read-write 0 Disable the selection. #0 1 Add 8 pF capacitor to the oscillator load. #1 DIV OSC_DIV 0x2 8 read-write n 0x0 0x0 ERPS ERCLK prescaler 6 2 read-write 00 The divisor ratio is 1. #00 01 The divisor ratio is 2. #01 10 The divisor ratio is 4. #10 11 The divisor ratio is 8. #11 PDB0 Programmable Delay Block PDB0 0x0 0x0 0x19C registers n PDB0 52 CH0C1 Channel n Control register 1 0x20 32 read-write n 0x0 0x0 BB PDB Channel Pre-Trigger Back-to-Back Operation Enable 16 8 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 BB0 PDB Channel Pre-Trigger Back-to-Back Operation Enable 16 1 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 BB1 PDB Channel Pre-Trigger Back-to-Back Operation Enable 17 1 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 BB2 PDB Channel Pre-Trigger Back-to-Back Operation Enable 18 1 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 BB3 PDB Channel Pre-Trigger Back-to-Back Operation Enable 19 1 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 BB4 PDB Channel Pre-Trigger Back-to-Back Operation Enable 20 1 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 BB5 PDB Channel Pre-Trigger Back-to-Back Operation Enable 21 1 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 BB6 PDB Channel Pre-Trigger Back-to-Back Operation Enable 22 1 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 BB7 PDB Channel Pre-Trigger Back-to-Back Operation Enable 23 1 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 EN PDB Channel Pre-Trigger Enable 0 8 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 EN0 PDB Channel Pre-Trigger Enable 0 1 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 EN1 PDB Channel Pre-Trigger Enable 1 1 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 EN2 PDB Channel Pre-Trigger Enable 2 1 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 EN3 PDB Channel Pre-Trigger Enable 3 1 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 EN4 PDB Channel Pre-Trigger Enable 4 1 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 EN5 PDB Channel Pre-Trigger Enable 5 1 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 EN6 PDB Channel Pre-Trigger Enable 6 1 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 EN7 PDB Channel Pre-Trigger Enable 7 1 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 TOS PDB Channel Pre-Trigger Output Select 8 8 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 TOS0 PDB Channel Pre-Trigger Output Select 8 1 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 TOS1 PDB Channel Pre-Trigger Output Select 9 1 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 TOS2 PDB Channel Pre-Trigger Output Select 10 1 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 TOS3 PDB Channel Pre-Trigger Output Select 11 1 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 TOS4 PDB Channel Pre-Trigger Output Select 12 1 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 TOS5 PDB Channel Pre-Trigger Output Select 13 1 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 TOS6 PDB Channel Pre-Trigger Output Select 14 1 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 TOS7 PDB Channel Pre-Trigger Output Select 15 1 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 CH0DLY0 Channel n Delay 0 register 0x30 32 read-write n 0x0 0x0 DLY PDB Channel Delay 0 16 read-write CH0DLY1 Channel n Delay 1 register 0x38 32 read-write n 0x0 0x0 DLY PDB Channel Delay 0 16 read-write CH0S Channel n Status register 0x28 32 read-write n 0x0 0x0 CF PDB Channel Flags 16 8 read-write ERR PDB Channel Sequence Error Flags 0 8 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 ERR0 PDB Channel Sequence Error Flags 0 1 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 ERR1 PDB Channel Sequence Error Flags 1 1 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 ERR2 PDB Channel Sequence Error Flags 2 1 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 ERR3 PDB Channel Sequence Error Flags 3 1 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 ERR4 PDB Channel Sequence Error Flags 4 1 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 ERR5 PDB Channel Sequence Error Flags 5 1 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 ERR6 PDB Channel Sequence Error Flags 6 1 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 ERR7 PDB Channel Sequence Error Flags 7 1 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 CH1C1 Channel n Control register 1 0x58 32 read-write n 0x0 0x0 BB PDB Channel Pre-Trigger Back-to-Back Operation Enable 16 8 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 BB0 PDB Channel Pre-Trigger Back-to-Back Operation Enable 16 1 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 BB1 PDB Channel Pre-Trigger Back-to-Back Operation Enable 17 1 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 BB2 PDB Channel Pre-Trigger Back-to-Back Operation Enable 18 1 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 BB3 PDB Channel Pre-Trigger Back-to-Back Operation Enable 19 1 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 BB4 PDB Channel Pre-Trigger Back-to-Back Operation Enable 20 1 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 BB5 PDB Channel Pre-Trigger Back-to-Back Operation Enable 21 1 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 BB6 PDB Channel Pre-Trigger Back-to-Back Operation Enable 22 1 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 BB7 PDB Channel Pre-Trigger Back-to-Back Operation Enable 23 1 read-write 0 PDB channel's corresponding pre-trigger back-to-back operation disabled. #0 1 PDB channel's corresponding pre-trigger back-to-back operation enabled. #1 EN PDB Channel Pre-Trigger Enable 0 8 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 EN0 PDB Channel Pre-Trigger Enable 0 1 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 EN1 PDB Channel Pre-Trigger Enable 1 1 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 EN2 PDB Channel Pre-Trigger Enable 2 1 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 EN3 PDB Channel Pre-Trigger Enable 3 1 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 EN4 PDB Channel Pre-Trigger Enable 4 1 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 EN5 PDB Channel Pre-Trigger Enable 5 1 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 EN6 PDB Channel Pre-Trigger Enable 6 1 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 EN7 PDB Channel Pre-Trigger Enable 7 1 read-write 0 PDB channel's corresponding pre-trigger disabled. #0 1 PDB channel's corresponding pre-trigger enabled. #1 TOS PDB Channel Pre-Trigger Output Select 8 8 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 TOS0 PDB Channel Pre-Trigger Output Select 8 1 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 TOS1 PDB Channel Pre-Trigger Output Select 9 1 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 TOS2 PDB Channel Pre-Trigger Output Select 10 1 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 TOS3 PDB Channel Pre-Trigger Output Select 11 1 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 TOS4 PDB Channel Pre-Trigger Output Select 12 1 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 TOS5 PDB Channel Pre-Trigger Output Select 13 1 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 TOS6 PDB Channel Pre-Trigger Output Select 14 1 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 TOS7 PDB Channel Pre-Trigger Output Select 15 1 read-write 0 PDB channel's corresponding pre-trigger is in bypassed mode. The pre-trigger asserts one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 PDB channel's corresponding pre-trigger asserts when the counter reaches the channel delay register and one peripheral clock cycle after a rising edge is detected on selected trigger input source or software trigger is selected and SETRIG is written with 1. #1 CH1DLY0 Channel n Delay 0 register 0x70 32 read-write n 0x0 0x0 DLY PDB Channel Delay 0 16 read-write CH1DLY1 Channel n Delay 1 register 0x7C 32 read-write n 0x0 0x0 DLY PDB Channel Delay 0 16 read-write CH1S Channel n Status register 0x64 32 read-write n 0x0 0x0 CF PDB Channel Flags 16 8 read-write ERR PDB Channel Sequence Error Flags 0 8 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 ERR0 PDB Channel Sequence Error Flags 0 1 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 ERR1 PDB Channel Sequence Error Flags 1 1 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 ERR2 PDB Channel Sequence Error Flags 2 1 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 ERR3 PDB Channel Sequence Error Flags 3 1 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 ERR4 PDB Channel Sequence Error Flags 4 1 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 ERR5 PDB Channel Sequence Error Flags 5 1 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 ERR6 PDB Channel Sequence Error Flags 6 1 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 ERR7 PDB Channel Sequence Error Flags 7 1 read-write 0 Sequence error not detected on PDB channel's corresponding pre-trigger. #0 1 Sequence error detected on PDB channel's corresponding pre-trigger. ADCn block can be triggered for a conversion by one pre-trigger from PDB channel n. When one conversion, which is triggered by one of the pre-triggers from PDB channel n, is in progress, new trigger from PDB channel's corresponding pre-trigger m cannot be accepted by ADCn, and ERR[m] is set. Writing 0's to clear the sequence error flags. #1 CNT Counter register 0x8 32 read-only n 0x0 0x0 CNT PDB Counter 0 16 read-only DACINT0 DAC Interval n register 0x2A8 32 read-write n 0x0 0x0 INT DAC Interval 0 16 read-write DACINT1 DAC Interval n register 0x404 32 read-write n 0x0 0x0 INT DAC Interval 0 16 read-write DACINTC0 DAC Interval Trigger n Control register 0x2A0 32 read-write n 0x0 0x0 EXT DAC External Trigger Input Enable 1 1 read-write 0 DAC external trigger input disabled. DAC interval counter is reset and counting starts when a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 DAC external trigger input enabled. DAC interval counter is bypassed and DAC external trigger input triggers the DAC interval trigger. #1 TOE DAC Interval Trigger Enable 0 1 read-write 0 DAC interval trigger disabled. #0 1 DAC interval trigger enabled. #1 DACINTC1 DAC Interval Trigger n Control register 0x3F8 32 read-write n 0x0 0x0 EXT DAC External Trigger Input Enable 1 1 read-write 0 DAC external trigger input disabled. DAC interval counter is reset and counting starts when a rising edge is detected on selected trigger input source or software trigger is selected and SWTRIG is written with 1. #0 1 DAC external trigger input enabled. DAC interval counter is bypassed and DAC external trigger input triggers the DAC interval trigger. #1 TOE DAC Interval Trigger Enable 0 1 read-write 0 DAC interval trigger disabled. #0 1 DAC interval trigger enabled. #1 IDLY Interrupt Delay register 0xC 32 read-write n 0x0 0x0 IDLY PDB Interrupt Delay 0 16 read-write MOD Modulus register 0x4 32 read-write n 0x0 0x0 MOD PDB Modulus 0 16 read-write PO0DLY Pulse-Out n Delay register 0x328 32 read-write n 0x0 0x0 DLY1 PDB Pulse-Out Delay 1 16 16 read-write DLY2 PDB Pulse-Out Delay 2 0 16 read-write PO1DLY Pulse-Out n Delay register 0x4C0 32 read-write n 0x0 0x0 DLY1 PDB Pulse-Out Delay 1 16 16 read-write DLY2 PDB Pulse-Out Delay 2 0 16 read-write POEN Pulse-Out n Enable register 0x190 32 read-write n 0x0 0x0 POEN PDB Pulse-Out Enable 0 8 read-write 0 PDB Pulse-Out disabled #0 1 PDB Pulse-Out enabled #1 POEN0 PDB Pulse-Out Enable 0 1 read-write 0 PDB Pulse-Out disabled #0 1 PDB Pulse-Out enabled #1 POEN1 PDB Pulse-Out Enable 1 1 read-write 0 PDB Pulse-Out disabled #0 1 PDB Pulse-Out enabled #1 POEN2 PDB Pulse-Out Enable 2 1 read-write 0 PDB Pulse-Out disabled #0 1 PDB Pulse-Out enabled #1 POEN3 PDB Pulse-Out Enable 3 1 read-write 0 PDB Pulse-Out disabled #0 1 PDB Pulse-Out enabled #1 POEN4 PDB Pulse-Out Enable 4 1 read-write 0 PDB Pulse-Out disabled #0 1 PDB Pulse-Out enabled #1 POEN5 PDB Pulse-Out Enable 5 1 read-write 0 PDB Pulse-Out disabled #0 1 PDB Pulse-Out enabled #1 POEN6 PDB Pulse-Out Enable 6 1 read-write 0 PDB Pulse-Out disabled #0 1 PDB Pulse-Out enabled #1 POEN7 PDB Pulse-Out Enable 7 1 read-write 0 PDB Pulse-Out disabled #0 1 PDB Pulse-Out enabled #1 SC Status and Control register 0x0 32 read-write n 0x0 0x0 CONT Continuous Mode Enable 1 1 read-write 0 PDB operation in One-Shot mode #0 1 PDB operation in Continuous mode #1 DMAEN DMA Enable 15 1 read-write 0 DMA disabled. #0 1 DMA enabled. #1 LDMOD Load Mode Select 18 2 read-write 00 The internal registers are loaded with the values from their buffers immediately after 1 is written to LDOK. #00 01 The internal registers are loaded with the values from their buffers when the PDB counter reaches the MOD register value after 1 is written to LDOK. #01 10 The internal registers are loaded with the values from their buffers when a trigger input event is detected after 1 is written to LDOK. #10 11 The internal registers are loaded with the values from their buffers when either the PDB counter reaches the MOD register value or a trigger input event is detected, after 1 is written to LDOK. #11 LDOK Load OK 0 1 read-write MULT Multiplication Factor Select for Prescaler 2 2 read-write 00 Multiplication factor is 1. #00 01 Multiplication factor is 10. #01 10 Multiplication factor is 20. #10 11 Multiplication factor is 40. #11 PDBEIE PDB Sequence Error Interrupt Enable 17 1 read-write 0 PDB sequence error interrupt disabled. #0 1 PDB sequence error interrupt enabled. #1 PDBEN PDB Enable 7 1 read-write 0 PDB disabled. Counter is off. #0 1 PDB enabled. #1 PDBIE PDB Interrupt Enable 5 1 read-write 0 PDB interrupt disabled. #0 1 PDB interrupt enabled. #1 PDBIF PDB Interrupt Flag 6 1 read-write PRESCALER Prescaler Divider Select 12 3 read-write 000 Counting uses the peripheral clock divided by multiplication factor selected by MULT. #000 001 Counting uses the peripheral clock divided by twice of the multiplication factor selected by MULT. #001 010 Counting uses the peripheral clock divided by four times of the multiplication factor selected by MULT. #010 011 Counting uses the peripheral clock divided by eight times of the multiplication factor selected by MULT. #011 100 Counting uses the peripheral clock divided by 16 times of the multiplication factor selected by MULT. #100 101 Counting uses the peripheral clock divided by 32 times of the multiplication factor selected by MULT. #101 110 Counting uses the peripheral clock divided by 64 times of the multiplication factor selected by MULT. #110 111 Counting uses the peripheral clock divided by 128 times of the multiplication factor selected by MULT. #111 SWTRIG Software Trigger 16 1 write-only TRGSEL Trigger Input Source Select 8 4 read-write 0000 Trigger-In 0 is selected. #0000 0001 Trigger-In 1 is selected. #0001 0010 Trigger-In 2 is selected. #0010 0011 Trigger-In 3 is selected. #0011 0100 Trigger-In 4 is selected. #0100 0101 Trigger-In 5 is selected. #0101 0110 Trigger-In 6 is selected. #0110 0111 Trigger-In 7 is selected. #0111 1000 Trigger-In 8 is selected. #1000 1001 Trigger-In 9 is selected. #1001 1010 Trigger-In 10 is selected. #1010 1011 Trigger-In 11 is selected. #1011 1100 Trigger-In 12 is selected. #1100 1101 Trigger-In 13 is selected. #1101 1110 Trigger-In 14 is selected. #1110 1111 Software trigger is selected. #1111 PIT Periodic Interrupt Timer PIT 0x0 0x0 0x140 registers n PIT0 48 PIT1 49 PIT2 50 PIT3 51 CVAL0 Current Timer Value Register 0x208 32 read-only n 0x0 0x0 TVL Current Timer Value 0 32 read-only CVAL1 Current Timer Value Register 0x31C 32 read-only n 0x0 0x0 TVL Current Timer Value 0 32 read-only CVAL2 Current Timer Value Register 0x440 32 read-only n 0x0 0x0 TVL Current Timer Value 0 32 read-only CVAL3 Current Timer Value Register 0x574 32 read-only n 0x0 0x0 TVL Current Timer Value 0 32 read-only LDVAL0 Timer Load Value Register 0x200 32 read-write n 0x0 0x0 TSV Timer Start Value 0 32 read-write LDVAL1 Timer Load Value Register 0x310 32 read-write n 0x0 0x0 TSV Timer Start Value 0 32 read-write LDVAL2 Timer Load Value Register 0x430 32 read-write n 0x0 0x0 TSV Timer Start Value 0 32 read-write LDVAL3 Timer Load Value Register 0x560 32 read-write n 0x0 0x0 TSV Timer Start Value 0 32 read-write MCR PIT Module Control Register 0x0 32 read-write n 0x0 0x0 FRZ Freeze 0 1 read-write 0 Timers continue to run in Debug mode. #0 1 Timers are stopped in Debug mode. #1 MDIS Module Disable - (PIT section) 1 1 read-write 0 Clock for standard PIT timers is enabled. #0 1 Clock for standard PIT timers is disabled. #1 TCTRL0 Timer Control Register 0x210 32 read-write n 0x0 0x0 CHN Chain Mode 2 1 read-write 0 Timer is not chained. #0 1 Timer is chained to previous timer. For example, for Channel 2, if this field is set, Timer 2 is chained to Timer 1. #1 TEN Timer Enable 0 1 read-write 0 Timer n is disabled. #0 1 Timer n is enabled. #1 TIE Timer Interrupt Enable 1 1 read-write 0 Interrupt requests from Timer n are disabled. #0 1 Interrupt will be requested whenever TIF is set. #1 TCTRL1 Timer Control Register 0x328 32 read-write n 0x0 0x0 CHN Chain Mode 2 1 read-write 0 Timer is not chained. #0 1 Timer is chained to previous timer. For example, for Channel 2, if this field is set, Timer 2 is chained to Timer 1. #1 TEN Timer Enable 0 1 read-write 0 Timer n is disabled. #0 1 Timer n is enabled. #1 TIE Timer Interrupt Enable 1 1 read-write 0 Interrupt requests from Timer n are disabled. #0 1 Interrupt will be requested whenever TIF is set. #1 TCTRL2 Timer Control Register 0x450 32 read-write n 0x0 0x0 CHN Chain Mode 2 1 read-write 0 Timer is not chained. #0 1 Timer is chained to previous timer. For example, for Channel 2, if this field is set, Timer 2 is chained to Timer 1. #1 TEN Timer Enable 0 1 read-write 0 Timer n is disabled. #0 1 Timer n is enabled. #1 TIE Timer Interrupt Enable 1 1 read-write 0 Interrupt requests from Timer n are disabled. #0 1 Interrupt will be requested whenever TIF is set. #1 TCTRL3 Timer Control Register 0x588 32 read-write n 0x0 0x0 CHN Chain Mode 2 1 read-write 0 Timer is not chained. #0 1 Timer is chained to previous timer. For example, for Channel 2, if this field is set, Timer 2 is chained to Timer 1. #1 TEN Timer Enable 0 1 read-write 0 Timer n is disabled. #0 1 Timer n is enabled. #1 TIE Timer Interrupt Enable 1 1 read-write 0 Interrupt requests from Timer n are disabled. #0 1 Interrupt will be requested whenever TIF is set. #1 TFLG0 Timer Flag Register 0x218 32 read-write n 0x0 0x0 TIF Timer Interrupt Flag 0 1 read-write 0 Timeout has not yet occurred. #0 1 Timeout has occurred. #1 TFLG1 Timer Flag Register 0x334 32 read-write n 0x0 0x0 TIF Timer Interrupt Flag 0 1 read-write 0 Timeout has not yet occurred. #0 1 Timeout has occurred. #1 TFLG2 Timer Flag Register 0x460 32 read-write n 0x0 0x0 TIF Timer Interrupt Flag 0 1 read-write 0 Timeout has not yet occurred. #0 1 Timeout has occurred. #1 TFLG3 Timer Flag Register 0x59C 32 read-write n 0x0 0x0 TIF Timer Interrupt Flag 0 1 read-write 0 Timeout has not yet occurred. #0 1 Timeout has occurred. #1 PMC Power Management Controller PMC 0x0 0x0 0x3 registers n LVD_LVW 20 LVDSC1 Low Voltage Detect Status And Control 1 register 0x0 8 read-write n 0x0 0x0 LVDACK Low-Voltage Detect Acknowledge 6 1 write-only LVDF Low-Voltage Detect Flag 7 1 read-only 0 Low-voltage event not detected #0 1 Low-voltage event detected #1 LVDIE Low-Voltage Detect Interrupt Enable 5 1 read-write 0 Hardware interrupt disabled (use polling) #0 1 Request a hardware interrupt when LVDF = 1 #1 LVDRE Low-Voltage Detect Reset Enable 4 1 read-write 0 LVDF does not generate hardware resets #0 1 Force an MCU reset when LVDF = 1 #1 LVDV Low-Voltage Detect Voltage Select 0 2 read-write 00 Low trip point selected (V LVD = V LVDL ) #00 01 High trip point selected (V LVD = V LVDH ) #01 LVDSC2 Low Voltage Detect Status And Control 2 register 0x1 8 read-write n 0x0 0x0 LVWACK Low-Voltage Warning Acknowledge 6 1 write-only LVWF Low-Voltage Warning Flag 7 1 read-only 0 Low-voltage warning event not detected #0 1 Low-voltage warning event detected #1 LVWIE Low-Voltage Warning Interrupt Enable 5 1 read-write 0 Hardware interrupt disabled (use polling) #0 1 Request a hardware interrupt when LVWF = 1 #1 LVWV Low-Voltage Warning Voltage Select 0 2 read-write 00 Low trip point selected (VLVW = VLVW1) #00 01 Mid 1 trip point selected (VLVW = VLVW2) #01 10 Mid 2 trip point selected (VLVW = VLVW3) #10 11 High trip point selected (VLVW = VLVW4) #11 REGSC Regulator Status And Control register 0x2 8 read-write n 0x0 0x0 ACKISO Acknowledge Isolation 3 1 read-write 0 Peripherals and I/O pads are in normal run state. #0 1 Certain peripherals and I/O pads are in an isolated and latched state. #1 BGBE Bandgap Buffer Enable 0 1 read-write 0 Bandgap buffer not enabled #0 1 Bandgap buffer enabled #1 BGEN Bandgap Enable In VLPx Operation 4 1 read-write 0 Bandgap voltage reference is disabled in VLPx , LLS , and VLLSx modes. #0 1 Bandgap voltage reference is enabled in VLPx , LLS , and VLLSx modes. #1 REGONS Regulator In Run Regulation Status 2 1 read-only 0 Regulator is in stop regulation or in transition to/from it #0 1 Regulator is in run regulation #1 PORTA Pin Control and Interrupts PORT 0x0 0x0 0xA4 registers n PORTA 59 GPCHR Global Pin Control High Register 0x84 32 write-only n 0x0 0x0 GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE0 Global Pin Write Enable 16 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE1 Global Pin Write Enable 17 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE10 Global Pin Write Enable 26 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE11 Global Pin Write Enable 27 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE12 Global Pin Write Enable 28 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE13 Global Pin Write Enable 29 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE14 Global Pin Write Enable 30 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE15 Global Pin Write Enable 31 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE2 Global Pin Write Enable 18 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE3 Global Pin Write Enable 19 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE4 Global Pin Write Enable 20 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE5 Global Pin Write Enable 21 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE6 Global Pin Write Enable 22 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE7 Global Pin Write Enable 23 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE8 Global Pin Write Enable 24 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE9 Global Pin Write Enable 25 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPCLR Global Pin Control Low Register 0x80 32 write-only n 0x0 0x0 GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE0 Global Pin Write Enable 16 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE1 Global Pin Write Enable 17 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE10 Global Pin Write Enable 26 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE11 Global Pin Write Enable 27 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE12 Global Pin Write Enable 28 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE13 Global Pin Write Enable 29 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE14 Global Pin Write Enable 30 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE15 Global Pin Write Enable 31 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE2 Global Pin Write Enable 18 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE3 Global Pin Write Enable 19 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE4 Global Pin Write Enable 20 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE5 Global Pin Write Enable 21 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE6 Global Pin Write Enable 22 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE7 Global Pin Write Enable 23 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE8 Global Pin Write Enable 24 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE9 Global Pin Write Enable 25 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 ISFR Interrupt Status Flag Register 0xA0 32 read-write n 0x0 0x0 ISF Interrupt Status Flag 0 32 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF0 Interrupt Status Flag 0 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF1 Interrupt Status Flag 1 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF10 Interrupt Status Flag 10 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF11 Interrupt Status Flag 11 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF12 Interrupt Status Flag 12 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF13 Interrupt Status Flag 13 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF14 Interrupt Status Flag 14 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF15 Interrupt Status Flag 15 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF16 Interrupt Status Flag 16 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF17 Interrupt Status Flag 17 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF18 Interrupt Status Flag 18 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF19 Interrupt Status Flag 19 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF2 Interrupt Status Flag 2 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF20 Interrupt Status Flag 20 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF21 Interrupt Status Flag 21 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF22 Interrupt Status Flag 22 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF23 Interrupt Status Flag 23 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF24 Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF25 Interrupt Status Flag 25 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF26 Interrupt Status Flag 26 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF27 Interrupt Status Flag 27 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF28 Interrupt Status Flag 28 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF29 Interrupt Status Flag 29 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF3 Interrupt Status Flag 3 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF30 Interrupt Status Flag 30 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF31 Interrupt Status Flag 31 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF4 Interrupt Status Flag 4 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF5 Interrupt Status Flag 5 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF6 Interrupt Status Flag 6 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF7 Interrupt Status Flag 7 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF8 Interrupt Status Flag 8 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF9 Interrupt Status Flag 9 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR0 Pin Control Register n 0x0 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR1 Pin Control Register n 0x4 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR10 Pin Control Register n 0x28 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR11 Pin Control Register n 0x2C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR12 Pin Control Register n 0x30 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR13 Pin Control Register n 0x34 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR14 Pin Control Register n 0x38 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR15 Pin Control Register n 0x3C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR16 Pin Control Register n 0x40 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR17 Pin Control Register n 0x44 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR18 Pin Control Register n 0x48 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR19 Pin Control Register n 0x4C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR2 Pin Control Register n 0x8 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR20 Pin Control Register n 0x50 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR21 Pin Control Register n 0x54 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR22 Pin Control Register n 0x58 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR23 Pin Control Register n 0x5C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR24 Pin Control Register n 0x60 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR25 Pin Control Register n 0x64 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR26 Pin Control Register n 0x68 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR27 Pin Control Register n 0x6C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR28 Pin Control Register n 0x70 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR29 Pin Control Register n 0x74 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR3 Pin Control Register n 0xC 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR30 Pin Control Register n 0x78 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR31 Pin Control Register n 0x7C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR4 Pin Control Register n 0x10 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-write 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR5 Pin Control Register n 0x14 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR6 Pin Control Register n 0x18 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR7 Pin Control Register n 0x1C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR8 Pin Control Register n 0x20 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR9 Pin Control Register n 0x24 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PORTB Pin Control and Interrupts PORT 0x0 0x0 0xA4 registers n PORTB 60 GPCHR Global Pin Control High Register 0x84 32 write-only n 0x0 0x0 GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE0 Global Pin Write Enable 16 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE1 Global Pin Write Enable 17 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE10 Global Pin Write Enable 26 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE11 Global Pin Write Enable 27 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE12 Global Pin Write Enable 28 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE13 Global Pin Write Enable 29 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE14 Global Pin Write Enable 30 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE15 Global Pin Write Enable 31 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE2 Global Pin Write Enable 18 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE3 Global Pin Write Enable 19 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE4 Global Pin Write Enable 20 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE5 Global Pin Write Enable 21 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE6 Global Pin Write Enable 22 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE7 Global Pin Write Enable 23 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE8 Global Pin Write Enable 24 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE9 Global Pin Write Enable 25 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPCLR Global Pin Control Low Register 0x80 32 write-only n 0x0 0x0 GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE0 Global Pin Write Enable 16 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE1 Global Pin Write Enable 17 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE10 Global Pin Write Enable 26 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE11 Global Pin Write Enable 27 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE12 Global Pin Write Enable 28 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE13 Global Pin Write Enable 29 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE14 Global Pin Write Enable 30 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE15 Global Pin Write Enable 31 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE2 Global Pin Write Enable 18 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE3 Global Pin Write Enable 19 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE4 Global Pin Write Enable 20 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE5 Global Pin Write Enable 21 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE6 Global Pin Write Enable 22 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE7 Global Pin Write Enable 23 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE8 Global Pin Write Enable 24 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE9 Global Pin Write Enable 25 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 ISFR Interrupt Status Flag Register 0xA0 32 read-write n 0x0 0x0 ISF Interrupt Status Flag 0 32 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF0 Interrupt Status Flag 0 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF1 Interrupt Status Flag 1 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF10 Interrupt Status Flag 10 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF11 Interrupt Status Flag 11 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF12 Interrupt Status Flag 12 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF13 Interrupt Status Flag 13 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF14 Interrupt Status Flag 14 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF15 Interrupt Status Flag 15 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF16 Interrupt Status Flag 16 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF17 Interrupt Status Flag 17 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF18 Interrupt Status Flag 18 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF19 Interrupt Status Flag 19 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF2 Interrupt Status Flag 2 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF20 Interrupt Status Flag 20 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF21 Interrupt Status Flag 21 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF22 Interrupt Status Flag 22 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF23 Interrupt Status Flag 23 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF24 Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF25 Interrupt Status Flag 25 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF26 Interrupt Status Flag 26 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF27 Interrupt Status Flag 27 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF28 Interrupt Status Flag 28 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF29 Interrupt Status Flag 29 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF3 Interrupt Status Flag 3 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF30 Interrupt Status Flag 30 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF31 Interrupt Status Flag 31 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF4 Interrupt Status Flag 4 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF5 Interrupt Status Flag 5 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF6 Interrupt Status Flag 6 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF7 Interrupt Status Flag 7 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF8 Interrupt Status Flag 8 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF9 Interrupt Status Flag 9 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR0 Pin Control Register n 0x0 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR1 Pin Control Register n 0x4 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR10 Pin Control Register n 0x28 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR11 Pin Control Register n 0x2C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR12 Pin Control Register n 0x30 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR13 Pin Control Register n 0x34 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR14 Pin Control Register n 0x38 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR15 Pin Control Register n 0x3C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR16 Pin Control Register n 0x40 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR17 Pin Control Register n 0x44 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR18 Pin Control Register n 0x48 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR19 Pin Control Register n 0x4C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR2 Pin Control Register n 0x8 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR20 Pin Control Register n 0x50 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR21 Pin Control Register n 0x54 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR22 Pin Control Register n 0x58 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR23 Pin Control Register n 0x5C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR24 Pin Control Register n 0x60 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR25 Pin Control Register n 0x64 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR26 Pin Control Register n 0x68 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR27 Pin Control Register n 0x6C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR28 Pin Control Register n 0x70 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR29 Pin Control Register n 0x74 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR3 Pin Control Register n 0xC 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR30 Pin Control Register n 0x78 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR31 Pin Control Register n 0x7C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR4 Pin Control Register n 0x10 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR5 Pin Control Register n 0x14 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR6 Pin Control Register n 0x18 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR7 Pin Control Register n 0x1C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR8 Pin Control Register n 0x20 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR9 Pin Control Register n 0x24 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PORTC Pin Control and Interrupts PORT 0x0 0x0 0xA4 registers n PORTC 61 GPCHR Global Pin Control High Register 0x84 32 write-only n 0x0 0x0 GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE0 Global Pin Write Enable 16 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE1 Global Pin Write Enable 17 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE10 Global Pin Write Enable 26 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE11 Global Pin Write Enable 27 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE12 Global Pin Write Enable 28 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE13 Global Pin Write Enable 29 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE14 Global Pin Write Enable 30 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE15 Global Pin Write Enable 31 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE2 Global Pin Write Enable 18 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE3 Global Pin Write Enable 19 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE4 Global Pin Write Enable 20 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE5 Global Pin Write Enable 21 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE6 Global Pin Write Enable 22 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE7 Global Pin Write Enable 23 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE8 Global Pin Write Enable 24 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE9 Global Pin Write Enable 25 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPCLR Global Pin Control Low Register 0x80 32 write-only n 0x0 0x0 GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE0 Global Pin Write Enable 16 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE1 Global Pin Write Enable 17 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE10 Global Pin Write Enable 26 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE11 Global Pin Write Enable 27 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE12 Global Pin Write Enable 28 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE13 Global Pin Write Enable 29 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE14 Global Pin Write Enable 30 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE15 Global Pin Write Enable 31 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE2 Global Pin Write Enable 18 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE3 Global Pin Write Enable 19 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE4 Global Pin Write Enable 20 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE5 Global Pin Write Enable 21 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE6 Global Pin Write Enable 22 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE7 Global Pin Write Enable 23 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE8 Global Pin Write Enable 24 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE9 Global Pin Write Enable 25 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 ISFR Interrupt Status Flag Register 0xA0 32 read-write n 0x0 0x0 ISF Interrupt Status Flag 0 32 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF0 Interrupt Status Flag 0 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF1 Interrupt Status Flag 1 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF10 Interrupt Status Flag 10 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF11 Interrupt Status Flag 11 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF12 Interrupt Status Flag 12 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF13 Interrupt Status Flag 13 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF14 Interrupt Status Flag 14 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF15 Interrupt Status Flag 15 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF16 Interrupt Status Flag 16 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF17 Interrupt Status Flag 17 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF18 Interrupt Status Flag 18 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF19 Interrupt Status Flag 19 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF2 Interrupt Status Flag 2 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF20 Interrupt Status Flag 20 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF21 Interrupt Status Flag 21 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF22 Interrupt Status Flag 22 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF23 Interrupt Status Flag 23 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF24 Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF25 Interrupt Status Flag 25 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF26 Interrupt Status Flag 26 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF27 Interrupt Status Flag 27 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF28 Interrupt Status Flag 28 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF29 Interrupt Status Flag 29 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF3 Interrupt Status Flag 3 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF30 Interrupt Status Flag 30 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF31 Interrupt Status Flag 31 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF4 Interrupt Status Flag 4 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF5 Interrupt Status Flag 5 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF6 Interrupt Status Flag 6 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF7 Interrupt Status Flag 7 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF8 Interrupt Status Flag 8 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF9 Interrupt Status Flag 9 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR0 Pin Control Register n 0x0 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR1 Pin Control Register n 0x4 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR10 Pin Control Register n 0x28 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR11 Pin Control Register n 0x2C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR12 Pin Control Register n 0x30 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR13 Pin Control Register n 0x34 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR14 Pin Control Register n 0x38 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR15 Pin Control Register n 0x3C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR16 Pin Control Register n 0x40 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR17 Pin Control Register n 0x44 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR18 Pin Control Register n 0x48 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR19 Pin Control Register n 0x4C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR2 Pin Control Register n 0x8 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR20 Pin Control Register n 0x50 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR21 Pin Control Register n 0x54 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR22 Pin Control Register n 0x58 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR23 Pin Control Register n 0x5C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR24 Pin Control Register n 0x60 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR25 Pin Control Register n 0x64 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR26 Pin Control Register n 0x68 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR27 Pin Control Register n 0x6C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR28 Pin Control Register n 0x70 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR29 Pin Control Register n 0x74 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR3 Pin Control Register n 0xC 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR30 Pin Control Register n 0x78 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR31 Pin Control Register n 0x7C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR4 Pin Control Register n 0x10 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR5 Pin Control Register n 0x14 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR6 Pin Control Register n 0x18 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR7 Pin Control Register n 0x1C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR8 Pin Control Register n 0x20 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR9 Pin Control Register n 0x24 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PORTD Pin Control and Interrupts PORT 0x0 0x0 0xCC registers n PORTD 62 DFCR Digital Filter Clock Register 0xC4 32 read-write n 0x0 0x0 CS Clock Source 0 1 read-write 0 Digital filters are clocked by the bus clock. #0 1 Digital filters are clocked by the 1 kHz LPO clock. #1 DFER Digital Filter Enable Register 0xC0 32 read-write n 0x0 0x0 DFE Digital Filter Enable 0 32 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE0 Digital Filter Enable 0 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE1 Digital Filter Enable 1 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE10 Digital Filter Enable 10 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE11 Digital Filter Enable 11 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE12 Digital Filter Enable 12 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE13 Digital Filter Enable 13 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE14 Digital Filter Enable 14 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE15 Digital Filter Enable 15 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE16 Digital Filter Enable 16 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE17 Digital Filter Enable 17 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE18 Digital Filter Enable 18 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE19 Digital Filter Enable 19 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE2 Digital Filter Enable 2 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE20 Digital Filter Enable 20 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE21 Digital Filter Enable 21 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE22 Digital Filter Enable 22 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE23 Digital Filter Enable 23 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE24 Digital Filter Enable 24 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE25 Digital Filter Enable 25 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE26 Digital Filter Enable 26 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE27 Digital Filter Enable 27 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE28 Digital Filter Enable 28 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE29 Digital Filter Enable 29 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE3 Digital Filter Enable 3 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE30 Digital Filter Enable 30 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE31 Digital Filter Enable 31 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE4 Digital Filter Enable 4 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE5 Digital Filter Enable 5 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE6 Digital Filter Enable 6 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE7 Digital Filter Enable 7 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE8 Digital Filter Enable 8 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFE9 Digital Filter Enable 9 1 read-write 0 Digital filter is disabled on the corresponding pin and output of the digital filter is reset to zero. #0 1 Digital filter is enabled on the corresponding pin, if the pin is configured as a digital input. #1 DFWR Digital Filter Width Register 0xC8 32 read-write n 0x0 0x0 FILT Filter Length 0 5 read-write GPCHR Global Pin Control High Register 0x84 32 write-only n 0x0 0x0 GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE0 Global Pin Write Enable 16 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE1 Global Pin Write Enable 17 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE10 Global Pin Write Enable 26 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE11 Global Pin Write Enable 27 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE12 Global Pin Write Enable 28 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE13 Global Pin Write Enable 29 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE14 Global Pin Write Enable 30 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE15 Global Pin Write Enable 31 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE2 Global Pin Write Enable 18 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE3 Global Pin Write Enable 19 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE4 Global Pin Write Enable 20 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE5 Global Pin Write Enable 21 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE6 Global Pin Write Enable 22 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE7 Global Pin Write Enable 23 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE8 Global Pin Write Enable 24 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE9 Global Pin Write Enable 25 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPCLR Global Pin Control Low Register 0x80 32 write-only n 0x0 0x0 GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE0 Global Pin Write Enable 16 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE1 Global Pin Write Enable 17 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE10 Global Pin Write Enable 26 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE11 Global Pin Write Enable 27 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE12 Global Pin Write Enable 28 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE13 Global Pin Write Enable 29 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE14 Global Pin Write Enable 30 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE15 Global Pin Write Enable 31 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE2 Global Pin Write Enable 18 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE3 Global Pin Write Enable 19 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE4 Global Pin Write Enable 20 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE5 Global Pin Write Enable 21 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE6 Global Pin Write Enable 22 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE7 Global Pin Write Enable 23 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE8 Global Pin Write Enable 24 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE9 Global Pin Write Enable 25 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 ISFR Interrupt Status Flag Register 0xA0 32 read-write n 0x0 0x0 ISF Interrupt Status Flag 0 32 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF0 Interrupt Status Flag 0 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF1 Interrupt Status Flag 1 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF10 Interrupt Status Flag 10 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF11 Interrupt Status Flag 11 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF12 Interrupt Status Flag 12 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF13 Interrupt Status Flag 13 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF14 Interrupt Status Flag 14 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF15 Interrupt Status Flag 15 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF16 Interrupt Status Flag 16 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF17 Interrupt Status Flag 17 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF18 Interrupt Status Flag 18 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF19 Interrupt Status Flag 19 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF2 Interrupt Status Flag 2 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF20 Interrupt Status Flag 20 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF21 Interrupt Status Flag 21 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF22 Interrupt Status Flag 22 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF23 Interrupt Status Flag 23 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF24 Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF25 Interrupt Status Flag 25 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF26 Interrupt Status Flag 26 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF27 Interrupt Status Flag 27 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF28 Interrupt Status Flag 28 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF29 Interrupt Status Flag 29 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF3 Interrupt Status Flag 3 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF30 Interrupt Status Flag 30 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF31 Interrupt Status Flag 31 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF4 Interrupt Status Flag 4 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF5 Interrupt Status Flag 5 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF6 Interrupt Status Flag 6 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF7 Interrupt Status Flag 7 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF8 Interrupt Status Flag 8 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF9 Interrupt Status Flag 9 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR0 Pin Control Register n 0x0 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR1 Pin Control Register n 0x4 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR10 Pin Control Register n 0x28 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR11 Pin Control Register n 0x2C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR12 Pin Control Register n 0x30 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR13 Pin Control Register n 0x34 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR14 Pin Control Register n 0x38 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR15 Pin Control Register n 0x3C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR16 Pin Control Register n 0x40 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR17 Pin Control Register n 0x44 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR18 Pin Control Register n 0x48 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR19 Pin Control Register n 0x4C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR2 Pin Control Register n 0x8 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR20 Pin Control Register n 0x50 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR21 Pin Control Register n 0x54 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR22 Pin Control Register n 0x58 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR23 Pin Control Register n 0x5C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR24 Pin Control Register n 0x60 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR25 Pin Control Register n 0x64 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR26 Pin Control Register n 0x68 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR27 Pin Control Register n 0x6C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR28 Pin Control Register n 0x70 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR29 Pin Control Register n 0x74 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR3 Pin Control Register n 0xC 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR30 Pin Control Register n 0x78 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR31 Pin Control Register n 0x7C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR4 Pin Control Register n 0x10 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR5 Pin Control Register n 0x14 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR6 Pin Control Register n 0x18 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR7 Pin Control Register n 0x1C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-write 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR8 Pin Control Register n 0x20 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR9 Pin Control Register n 0x24 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PORTE Pin Control and Interrupts PORT 0x0 0x0 0xA4 registers n PORTE 63 GPCHR Global Pin Control High Register 0x84 32 write-only n 0x0 0x0 GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE0 Global Pin Write Enable 16 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE1 Global Pin Write Enable 17 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE10 Global Pin Write Enable 26 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE11 Global Pin Write Enable 27 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE12 Global Pin Write Enable 28 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE13 Global Pin Write Enable 29 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE14 Global Pin Write Enable 30 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE15 Global Pin Write Enable 31 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE2 Global Pin Write Enable 18 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE3 Global Pin Write Enable 19 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE4 Global Pin Write Enable 20 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE5 Global Pin Write Enable 21 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE6 Global Pin Write Enable 22 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE7 Global Pin Write Enable 23 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE8 Global Pin Write Enable 24 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE9 Global Pin Write Enable 25 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPCLR Global Pin Control Low Register 0x80 32 write-only n 0x0 0x0 GPWD Global Pin Write Data 0 16 write-only GPWE Global Pin Write Enable 16 16 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE0 Global Pin Write Enable 16 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE1 Global Pin Write Enable 17 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE10 Global Pin Write Enable 26 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE11 Global Pin Write Enable 27 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE12 Global Pin Write Enable 28 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE13 Global Pin Write Enable 29 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE14 Global Pin Write Enable 30 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE15 Global Pin Write Enable 31 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE2 Global Pin Write Enable 18 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE3 Global Pin Write Enable 19 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE4 Global Pin Write Enable 20 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE5 Global Pin Write Enable 21 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE6 Global Pin Write Enable 22 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE7 Global Pin Write Enable 23 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE8 Global Pin Write Enable 24 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 GPWE9 Global Pin Write Enable 25 1 write-only 0 Corresponding Pin Control Register is not updated with the value in GPWD. #0 1 Corresponding Pin Control Register is updated with the value in GPWD. #1 ISFR Interrupt Status Flag Register 0xA0 32 read-write n 0x0 0x0 ISF Interrupt Status Flag 0 32 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF0 Interrupt Status Flag 0 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF1 Interrupt Status Flag 1 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF10 Interrupt Status Flag 10 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF11 Interrupt Status Flag 11 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF12 Interrupt Status Flag 12 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF13 Interrupt Status Flag 13 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF14 Interrupt Status Flag 14 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF15 Interrupt Status Flag 15 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF16 Interrupt Status Flag 16 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF17 Interrupt Status Flag 17 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF18 Interrupt Status Flag 18 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF19 Interrupt Status Flag 19 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF2 Interrupt Status Flag 2 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF20 Interrupt Status Flag 20 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF21 Interrupt Status Flag 21 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF22 Interrupt Status Flag 22 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF23 Interrupt Status Flag 23 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF24 Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF25 Interrupt Status Flag 25 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF26 Interrupt Status Flag 26 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF27 Interrupt Status Flag 27 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF28 Interrupt Status Flag 28 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF29 Interrupt Status Flag 29 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF3 Interrupt Status Flag 3 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF30 Interrupt Status Flag 30 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF31 Interrupt Status Flag 31 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF4 Interrupt Status Flag 4 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF5 Interrupt Status Flag 5 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF6 Interrupt Status Flag 6 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF7 Interrupt Status Flag 7 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF8 Interrupt Status Flag 8 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 ISF9 Interrupt Status Flag 9 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 PCR0 Pin Control Register n 0x0 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR1 Pin Control Register n 0x4 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR10 Pin Control Register n 0x28 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR11 Pin Control Register n 0x2C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR12 Pin Control Register n 0x30 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR13 Pin Control Register n 0x34 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR14 Pin Control Register n 0x38 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR15 Pin Control Register n 0x3C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR16 Pin Control Register n 0x40 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR17 Pin Control Register n 0x44 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR18 Pin Control Register n 0x48 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR19 Pin Control Register n 0x4C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR2 Pin Control Register n 0x8 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR20 Pin Control Register n 0x50 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR21 Pin Control Register n 0x54 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR22 Pin Control Register n 0x58 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR23 Pin Control Register n 0x5C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR24 Pin Control Register n 0x60 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR25 Pin Control Register n 0x64 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR26 Pin Control Register n 0x68 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR27 Pin Control Register n 0x6C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR28 Pin Control Register n 0x70 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR29 Pin Control Register n 0x74 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR3 Pin Control Register n 0xC 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR30 Pin Control Register n 0x78 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR31 Pin Control Register n 0x7C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR4 Pin Control Register n 0x10 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR5 Pin Control Register n 0x14 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR6 Pin Control Register n 0x18 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-write 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-write 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-write 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-write 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR7 Pin Control Register n 0x1C 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR8 Pin Control Register n 0x20 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PCR9 Pin Control Register n 0x24 32 read-write n 0x0 0x0 DSE Drive Strength Enable 6 1 read-only 0 Low drive strength is configured on the corresponding pin, if pin is configured as a digital output. #0 1 High drive strength is configured on the corresponding pin, if pin is configured as a digital output. #1 IRQC Interrupt Configuration 16 4 read-write 0000 Interrupt/DMA request disabled. #0000 0001 DMA request on rising edge. #0001 0010 DMA request on falling edge. #0010 0011 DMA request on either edge. #0011 1000 Interrupt when logic 0. #1000 1001 Interrupt on rising-edge. #1001 1010 Interrupt on falling-edge. #1010 1011 Interrupt on either edge. #1011 1100 Interrupt when logic 1. #1100 ISF Interrupt Status Flag 24 1 read-write 0 Configured interrupt is not detected. #0 1 Configured interrupt is detected. If the pin is configured to generate a DMA request, then the corresponding flag will be cleared automatically at the completion of the requested DMA transfer. Otherwise, the flag remains set until a logic 1 is written to the flag. If the pin is configured for a level sensitive interrupt and the pin remains asserted, then the flag is set again immediately after it is cleared. #1 LK Lock Register 15 1 read-write 0 Pin Control Register fields [15:0] are not locked. #0 1 Pin Control Register fields [15:0] are locked and cannot be updated until the next system reset. #1 MUX Pin Mux Control 8 3 read-write 000 Pin disabled (analog). #000 001 Alternative 1 (GPIO). #001 010 Alternative 2 (chip-specific). #010 011 Alternative 3 (chip-specific). #011 100 Alternative 4 (chip-specific). #100 101 Alternative 5 (chip-specific). #101 110 Alternative 6 (chip-specific). #110 111 Alternative 7 (chip-specific). #111 ODE Open Drain Enable 5 1 read-only 0 Open drain output is disabled on the corresponding pin. #0 1 Open drain output is enabled on the corresponding pin, if the pin is configured as a digital output. #1 PE Pull Enable 1 1 read-only 0 Internal pullup or pulldown resistor is not enabled on the corresponding pin. #0 1 Internal pullup or pulldown resistor is enabled on the corresponding pin, if the pin is configured as a digital input. #1 PFE Passive Filter Enable 4 1 read-only 0 Passive input filter is disabled on the corresponding pin. #0 1 Passive input filter is enabled on the corresponding pin, if the pin is configured as a digital input. Refer to the device data sheet for filter characteristics. #1 PS Pull Select 0 1 read-only 0 Internal pulldown resistor is enabled on the corresponding pin, if the corresponding PE field is set. #0 1 Internal pullup resistor is enabled on the corresponding pin, if the corresponding PE field is set. #1 SRE Slew Rate Enable 2 1 read-only 0 Fast slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #0 1 Slow slew rate is configured on the corresponding pin, if the pin is configured as a digital output. #1 PTA General Purpose Input/Output GPIO 0x0 0x0 0x18 registers n PORTA 59 PCOR Port Clear Output Register 0x8 32 write-only n 0x0 0x0 PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PDDR Port Data Direction Register 0x14 32 read-write n 0x0 0x0 PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDIR Port Data Input Register 0x10 32 read-only n 0x0 0x0 PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDOR Port Data Output Register 0x0 32 read-write n 0x0 0x0 PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only n 0x0 0x0 PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTOR Port Toggle Output Register 0xC 32 write-only n 0x0 0x0 PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTB General Purpose Input/Output GPIO 0x0 0x0 0x18 registers n PORTB 60 PCOR Port Clear Output Register 0x8 32 write-only n 0x0 0x0 PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PDDR Port Data Direction Register 0x14 32 read-write n 0x0 0x0 PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDIR Port Data Input Register 0x10 32 read-only n 0x0 0x0 PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDOR Port Data Output Register 0x0 32 read-write n 0x0 0x0 PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only n 0x0 0x0 PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTOR Port Toggle Output Register 0xC 32 write-only n 0x0 0x0 PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTC General Purpose Input/Output GPIO 0x0 0x0 0x18 registers n PORTC 61 PCOR Port Clear Output Register 0x8 32 write-only n 0x0 0x0 PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PDDR Port Data Direction Register 0x14 32 read-write n 0x0 0x0 PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDIR Port Data Input Register 0x10 32 read-only n 0x0 0x0 PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDOR Port Data Output Register 0x0 32 read-write n 0x0 0x0 PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only n 0x0 0x0 PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTOR Port Toggle Output Register 0xC 32 write-only n 0x0 0x0 PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTD General Purpose Input/Output GPIO 0x0 0x0 0x18 registers n PORTD 62 PCOR Port Clear Output Register 0x8 32 write-only n 0x0 0x0 PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PDDR Port Data Direction Register 0x14 32 read-write n 0x0 0x0 PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDIR Port Data Input Register 0x10 32 read-only n 0x0 0x0 PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDOR Port Data Output Register 0x0 32 read-write n 0x0 0x0 PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only n 0x0 0x0 PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTOR Port Toggle Output Register 0xC 32 write-only n 0x0 0x0 PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 PTE General Purpose Input/Output GPIO 0x0 0x0 0x18 registers n PORTE 63 PCOR Port Clear Output Register 0x8 32 write-only n 0x0 0x0 PTCO Port Clear Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is cleared to logic 0. #1 PDDR Port Data Direction Register 0x14 32 read-write n 0x0 0x0 PDD Port Data Direction 0 32 read-write 0 Pin is configured as general-purpose input, for the GPIO function. #0 1 Pin is configured as general-purpose output, for the GPIO function. #1 PDIR Port Data Input Register 0x10 32 read-only n 0x0 0x0 PDI Port Data Input 0 32 read-only 0 Pin logic level is logic 0, or is not configured for use by digital function. #0 1 Pin logic level is logic 1. #1 PDOR Port Data Output Register 0x0 32 read-write n 0x0 0x0 PDO Port Data Output 0 32 read-write 0 Logic level 0 is driven on pin, provided pin is configured for general-purpose output. #0 1 Logic level 1 is driven on pin, provided pin is configured for general-purpose output. #1 PSOR Port Set Output Register 0x4 32 write-only n 0x0 0x0 PTSO Port Set Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to logic 1. #1 PTOR Port Toggle Output Register 0xC 32 write-only n 0x0 0x0 PTTO Port Toggle Output 0 32 write-only 0 Corresponding bit in PDORn does not change. #0 1 Corresponding bit in PDORn is set to the inverse of its existing logic state. #1 RCM Reset Control Module RCM 0x0 0x0 0xA registers n MR Mode Register 0x7 8 read-only n 0x0 0x0 EZP_MS EZP_MS_B pin state 1 1 read-only 0 Pin deasserted (logic 1) #0 1 Pin asserted (logic 0) #1 RPFC Reset Pin Filter Control register 0x4 8 read-write n 0x0 0x0 RSTFLTSRW Reset Pin Filter Select in Run and Wait Modes 0 2 read-write 00 All filtering disabled #00 01 Bus clock filter enabled for normal operation #01 10 LPO clock filter enabled for normal operation #10 RSTFLTSS Reset Pin Filter Select in Stop Mode 2 1 read-write 0 All filtering disabled #0 1 LPO clock filter enabled #1 RPFW Reset Pin Filter Width register 0x5 8 read-write n 0x0 0x0 RSTFLTSEL Reset Pin Filter Bus Clock Select 0 5 read-write 00000 Bus clock filter count is 1 #00000 00001 Bus clock filter count is 2 #00001 00010 Bus clock filter count is 3 #00010 00011 Bus clock filter count is 4 #00011 00100 Bus clock filter count is 5 #00100 00101 Bus clock filter count is 6 #00101 00110 Bus clock filter count is 7 #00110 00111 Bus clock filter count is 8 #00111 01000 Bus clock filter count is 9 #01000 01001 Bus clock filter count is 10 #01001 01010 Bus clock filter count is 11 #01010 01011 Bus clock filter count is 12 #01011 01100 Bus clock filter count is 13 #01100 01101 Bus clock filter count is 14 #01101 01110 Bus clock filter count is 15 #01110 01111 Bus clock filter count is 16 #01111 10000 Bus clock filter count is 17 #10000 10001 Bus clock filter count is 18 #10001 10010 Bus clock filter count is 19 #10010 10011 Bus clock filter count is 20 #10011 10100 Bus clock filter count is 21 #10100 10101 Bus clock filter count is 22 #10101 10110 Bus clock filter count is 23 #10110 10111 Bus clock filter count is 24 #10111 11000 Bus clock filter count is 25 #11000 11001 Bus clock filter count is 26 #11001 11010 Bus clock filter count is 27 #11010 11011 Bus clock filter count is 28 #11011 11100 Bus clock filter count is 29 #11100 11101 Bus clock filter count is 30 #11101 11110 Bus clock filter count is 31 #11110 11111 Bus clock filter count is 32 #11111 SRS0 System Reset Status Register 0 0x0 8 read-only n 0x0 0x0 LOC Loss-of-Clock Reset 2 1 read-only 0 Reset not caused by a loss of external clock. #0 1 Reset caused by a loss of external clock. #1 LOL Loss-of-Lock Reset 3 1 read-only 0 Reset not caused by a loss of lock in the PLL #0 1 Reset caused by a loss of lock in the PLL #1 LVD Low-Voltage Detect Reset 1 1 read-only 0 Reset not caused by LVD trip or POR #0 1 Reset caused by LVD trip or POR #1 PIN External Reset Pin 6 1 read-only 0 Reset not caused by external reset pin #0 1 Reset caused by external reset pin #1 POR Power-On Reset 7 1 read-only 0 Reset not caused by POR #0 1 Reset caused by POR #1 WAKEUP Low Leakage Wakeup Reset 0 1 read-only 0 Reset not caused by LLWU module wakeup source #0 1 Reset caused by LLWU module wakeup source #1 WDOG Watchdog 5 1 read-only 0 Reset not caused by watchdog timeout #0 1 Reset caused by watchdog timeout #1 SRS1 System Reset Status Register 1 0x1 8 read-only n 0x0 0x0 EZPT EzPort Reset 4 1 read-only 0 Reset not caused by EzPort receiving the RESET command while the device is in EzPort mode #0 1 Reset caused by EzPort receiving the RESET command while the device is in EzPort mode #1 JTAG JTAG Generated Reset 0 1 read-only 0 Reset not caused by JTAG #0 1 Reset caused by JTAG #1 LOCKUP Core Lockup 1 1 read-only 0 Reset not caused by core LOCKUP event #0 1 Reset caused by core LOCKUP event #1 MDM_AP MDM-AP System Reset Request 3 1 read-only 0 Reset not caused by host debugger system setting of the System Reset Request bit #0 1 Reset caused by host debugger system setting of the System Reset Request bit #1 SACKERR Stop Mode Acknowledge Error Reset 5 1 read-only 0 Reset not caused by peripheral failure to acknowledge attempt to enter stop mode #0 1 Reset caused by peripheral failure to acknowledge attempt to enter stop mode #1 SW Software 2 1 read-only 0 Reset not caused by software setting of SYSRESETREQ bit #0 1 Reset caused by software setting of SYSRESETREQ bit #1 SSRS0 Sticky System Reset Status Register 0 0x8 8 read-write n 0x0 0x0 SLOC Sticky Loss-of-Clock Reset 2 1 read-write 0 Reset not caused by a loss of external clock. #0 1 Reset caused by a loss of external clock. #1 SLOL Sticky Loss-of-Lock Reset 3 1 read-write 0 Reset not caused by a loss of lock in the PLL #0 1 Reset caused by a loss of lock in the PLL #1 SLVD Sticky Low-Voltage Detect Reset 1 1 read-write 0 Reset not caused by LVD trip or POR #0 1 Reset caused by LVD trip or POR #1 SPIN Sticky External Reset Pin 6 1 read-write 0 Reset not caused by external reset pin #0 1 Reset caused by external reset pin #1 SPOR Sticky Power-On Reset 7 1 read-write 0 Reset not caused by POR #0 1 Reset caused by POR #1 SWAKEUP Sticky Low Leakage Wakeup Reset 0 1 read-write 0 Reset not caused by LLWU module wakeup source #0 1 Reset caused by LLWU module wakeup source #1 SWDOG Sticky Watchdog 5 1 read-write 0 Reset not caused by watchdog timeout #0 1 Reset caused by watchdog timeout #1 SSRS1 Sticky System Reset Status Register 1 0x9 8 read-write n 0x0 0x0 SEZPT Sticky EzPort Reset 4 1 read-write 0 Reset not caused by EzPort receiving the RESET command while the device is in EzPort mode #0 1 Reset caused by EzPort receiving the RESET command while the device is in EzPort mode #1 SJTAG Sticky JTAG Generated Reset 0 1 read-write 0 Reset not caused by JTAG #0 1 Reset caused by JTAG #1 SLOCKUP Sticky Core Lockup 1 1 read-write 0 Reset not caused by core LOCKUP event #0 1 Reset caused by core LOCKUP event #1 SMDM_AP Sticky MDM-AP System Reset Request 3 1 read-write 0 Reset not caused by host debugger system setting of the System Reset Request bit #0 1 Reset caused by host debugger system setting of the System Reset Request bit #1 SSACKERR Sticky Stop Mode Acknowledge Error Reset 5 1 read-write 0 Reset not caused by peripheral failure to acknowledge attempt to enter stop mode #0 1 Reset caused by peripheral failure to acknowledge attempt to enter stop mode #1 SSW Sticky Software 2 1 read-write 0 Reset not caused by software setting of SYSRESETREQ bit #0 1 Reset caused by software setting of SYSRESETREQ bit #1 RFSYS System register file RFSYS 0x0 0x0 0x20 registers n REG0 Register file register 0x0 32 read-write n 0x0 0x0 HH High higher byte 24 8 read-write HL High lower byte 16 8 read-write LH Low higher byte 8 8 read-write LL Low lower byte 0 8 read-write REG1 Register file register 0x4 32 read-write n 0x0 0x0 HH High higher byte 24 8 read-write HL High lower byte 16 8 read-write LH Low higher byte 8 8 read-write LL Low lower byte 0 8 read-write REG2 Register file register 0xC 32 read-write n 0x0 0x0 HH High higher byte 24 8 read-write HL High lower byte 16 8 read-write LH Low higher byte 8 8 read-write LL Low lower byte 0 8 read-write REG3 Register file register 0x18 32 read-write n 0x0 0x0 HH High higher byte 24 8 read-write HL High lower byte 16 8 read-write LH Low higher byte 8 8 read-write LL Low lower byte 0 8 read-write REG4 Register file register 0x28 32 read-write n 0x0 0x0 HH High higher byte 24 8 read-write HL High lower byte 16 8 read-write LH Low higher byte 8 8 read-write LL Low lower byte 0 8 read-write REG5 Register file register 0x3C 32 read-write n 0x0 0x0 HH High higher byte 24 8 read-write HL High lower byte 16 8 read-write LH Low higher byte 8 8 read-write LL Low lower byte 0 8 read-write REG6 Register file register 0x54 32 read-write n 0x0 0x0 HH High higher byte 24 8 read-write HL High lower byte 16 8 read-write LH Low higher byte 8 8 read-write LL Low lower byte 0 8 read-write REG7 Register file register 0x70 32 read-write n 0x0 0x0 HH High higher byte 24 8 read-write HL High lower byte 16 8 read-write LH Low higher byte 8 8 read-write LL Low lower byte 0 8 read-write RFVBAT VBAT register file RFVBAT 0x0 0x0 0x20 registers n REG0 VBAT register file register 0x0 32 read-write n 0x0 0x0 HH High higher byte 24 8 read-write HL High lower byte 16 8 read-write LH Low higher byte 8 8 read-write LL Low lower byte 0 8 read-write REG1 VBAT register file register 0x4 32 read-write n 0x0 0x0 HH High higher byte 24 8 read-write HL High lower byte 16 8 read-write LH Low higher byte 8 8 read-write LL Low lower byte 0 8 read-write REG2 VBAT register file register 0xC 32 read-write n 0x0 0x0 HH High higher byte 24 8 read-write HL High lower byte 16 8 read-write LH Low higher byte 8 8 read-write LL Low lower byte 0 8 read-write REG3 VBAT register file register 0x18 32 read-write n 0x0 0x0 HH High higher byte 24 8 read-write HL High lower byte 16 8 read-write LH Low higher byte 8 8 read-write LL Low lower byte 0 8 read-write REG4 VBAT register file register 0x28 32 read-write n 0x0 0x0 HH High higher byte 24 8 read-write HL High lower byte 16 8 read-write LH Low higher byte 8 8 read-write LL Low lower byte 0 8 read-write REG5 VBAT register file register 0x3C 32 read-write n 0x0 0x0 HH High higher byte 24 8 read-write HL High lower byte 16 8 read-write LH Low higher byte 8 8 read-write LL Low lower byte 0 8 read-write REG6 VBAT register file register 0x54 32 read-write n 0x0 0x0 HH High higher byte 24 8 read-write HL High lower byte 16 8 read-write LH Low higher byte 8 8 read-write LL Low lower byte 0 8 read-write REG7 VBAT register file register 0x70 32 read-write n 0x0 0x0 HH High higher byte 24 8 read-write HL High lower byte 16 8 read-write LH Low higher byte 8 8 read-write LL Low lower byte 0 8 read-write RNG Random Number Generator Accelerator RNG 0x0 0x0 0x10 registers n RNG 23 CR RNGA Control Register 0x0 32 read-write n 0x0 0x0 CLRI Clear Interrupt 3 1 write-only 0 Do not clear the interrupt. #0 1 Clear the interrupt. When you write 1 to this field, RNGA then resets the error-interrupt indicator (SR[ERRI]). This bit always reads as 0. #1 GO Go 0 1 read-write 0 Disabled #0 1 Enabled #1 HA High Assurance 1 1 read-write 0 Disabled #0 1 Enabled #1 INTM Interrupt Mask 2 1 read-write 0 Not masked #0 1 Masked #1 SLP Sleep 4 1 read-write 0 Normal mode #0 1 Sleep (low-power) mode #1 ER RNGA Entropy Register 0x8 32 write-only n 0x0 0x0 EXT_ENT External Entropy 0 32 write-only OR RNGA Output Register 0xC 32 read-only n 0x0 0x0 RANDOUT Random Output 0 32 read-only 0 Invalid data (if you read this field when it is 0 and SR[OREG_LVL] is 0, RNGA then writes 1 to SR[ERRI], SR[ORU], and SR[LRS]; when the error interrupt is not masked (CR[INTM]=0), RNGA also asserts an error interrupt request to the interrupt controller). #0 SR RNGA Status Register 0x4 32 read-only n 0x0 0x0 ERRI Error Interrupt 3 1 read-only 0 No underflow #0 1 Underflow #1 LRS Last Read Status 1 1 read-only 0 No underflow #0 1 Underflow #1 OREG_LVL Output Register Level 8 8 read-only 0 No words (empty) #0 1 One word (valid) #1 OREG_SIZE Output Register Size 16 8 read-only 1 One word (this value is fixed) #1 ORU Output Register Underflow 2 1 read-only 0 No underflow #0 1 Underflow #1 SECV Security Violation 0 1 read-only 0 No security violation #0 1 Security violation #1 SLP Sleep 4 1 read-only 0 Normal mode #0 1 Sleep (low-power) mode #1 RTC Secure Real Time Clock RTC 0x0 0x0 0x808 registers n RTC 46 RTC_Seconds 47 CR RTC Control Register 0x10 32 read-write n 0x0 0x0 CLKO Clock Output 9 1 read-write 0 The 32 kHz clock is output to other peripherals. #0 1 The 32 kHz clock is not output to other peripherals. #1 OSCE Oscillator Enable 8 1 read-write 0 32.768 kHz oscillator is disabled. #0 1 32.768 kHz oscillator is enabled. After setting this bit, wait the oscillator startup time before enabling the time counter to allow the 32.768 kHz clock time to stabilize. #1 SC16P Oscillator 16pF Load Configure 10 1 read-write 0 Disable the load. #0 1 Enable the additional load. #1 SC2P Oscillator 2pF Load Configure 13 1 read-write 0 Disable the load. #0 1 Enable the additional load. #1 SC4P Oscillator 4pF Load Configure 12 1 read-write 0 Disable the load. #0 1 Enable the additional load. #1 SC8P Oscillator 8pF Load Configure 11 1 read-write 0 Disable the load. #0 1 Enable the additional load. #1 SUP Supervisor Access 2 1 read-write 0 Non-supervisor mode write accesses are not supported and generate a bus error. #0 1 Non-supervisor mode write accesses are supported. #1 SWR Software Reset 0 1 read-write 0 No effect. #0 1 Resets all RTC registers except for the SWR bit and the RTC_WAR and RTC_RAR registers . The SWR bit is cleared by VBAT POR and by software explicitly clearing it. #1 UM Update Mode 3 1 read-write 0 Registers cannot be written when locked. #0 1 Registers can be written when locked under limited conditions. #1 WPE Wakeup Pin Enable 1 1 read-write 0 Wakeup pin is disabled. #0 1 Wakeup pin is enabled and wakeup pin asserts if the RTC interrupt asserts or the wakeup pin is turned on. #1 WPS Wakeup Pin Select 4 1 read-write 0 Wakeup pin asserts (active low, open drain) if the RTC interrupt asserts or the wakeup pin is turned on. #0 1 Wakeup pin instead outputs the RTC 32kHz clock, provided the wakeup pin is turned on and the 32kHz clock is output to other peripherals. #1 IER RTC Interrupt Enable Register 0x1C 32 read-write n 0x0 0x0 TAIE Time Alarm Interrupt Enable 2 1 read-write 0 Time alarm flag does not generate an interrupt. #0 1 Time alarm flag does generate an interrupt. #1 TIIE Time Invalid Interrupt Enable 0 1 read-write 0 Time invalid flag does not generate an interrupt. #0 1 Time invalid flag does generate an interrupt. #1 TOIE Time Overflow Interrupt Enable 1 1 read-write 0 Time overflow flag does not generate an interrupt. #0 1 Time overflow flag does generate an interrupt. #1 TSIE Time Seconds Interrupt Enable 4 1 read-write 0 Seconds interrupt is disabled. #0 1 Seconds interrupt is enabled. #1 WPON Wakeup Pin On 7 1 read-write 0 No effect. #0 1 If the wakeup pin is enabled, then the wakeup pin will assert. #1 LR RTC Lock Register 0x18 32 read-write n 0x0 0x0 CRL Control Register Lock 4 1 read-write 0 Control Register is locked and writes are ignored. #0 1 Control Register is not locked and writes complete as normal. #1 LRL Lock Register Lock 6 1 read-write 0 Lock Register is locked and writes are ignored. #0 1 Lock Register is not locked and writes complete as normal. #1 SRL Status Register Lock 5 1 read-write 0 Status Register is locked and writes are ignored. #0 1 Status Register is not locked and writes complete as normal. #1 TCL Time Compensation Lock 3 1 read-write 0 Time Compensation Register is locked and writes are ignored. #0 1 Time Compensation Register is not locked and writes complete as normal. #1 RAR RTC Read Access Register 0x804 32 read-write n 0x0 0x0 CRR Control Register Read 4 1 read-write 0 Reads to the Control Register are ignored. #0 1 Reads to the Control Register complete as normal. #1 IERR Interrupt Enable Register Read 7 1 read-write 0 Reads to the Interrupt Enable Register are ignored. #0 1 Reads to the Interrupt Enable Register complete as normal. #1 LRR Lock Register Read 6 1 read-write 0 Reads to the Lock Register are ignored. #0 1 Reads to the Lock Register complete as normal. #1 SRR Status Register Read 5 1 read-write 0 Reads to the Status Register are ignored. #0 1 Reads to the Status Register complete as normal. #1 TARR Time Alarm Register Read 2 1 read-write 0 Reads to the Time Alarm Register are ignored. #0 1 Reads to the Time Alarm Register complete as normal. #1 TCRR Time Compensation Register Read 3 1 read-write 0 Reads to the Time Compensation Register are ignored. #0 1 Reads to the Time Compensation Register complete as normal. #1 TPRR Time Prescaler Register Read 1 1 read-write 0 Reads to the Time Pprescaler Register are ignored. #0 1 Reads to the Time Prescaler Register complete as normal. #1 TSRR Time Seconds Register Read 0 1 read-write 0 Reads to the Time Seconds Register are ignored. #0 1 Reads to the Time Seconds Register complete as normal. #1 SR RTC Status Register 0x14 32 read-write n 0x0 0x0 TAF Time Alarm Flag 2 1 read-only 0 Time alarm has not occurred. #0 1 Time alarm has occurred. #1 TCE Time Counter Enable 4 1 read-write 0 Time counter is disabled. #0 1 Time counter is enabled. #1 TIF Time Invalid Flag 0 1 read-only 0 Time is valid. #0 1 Time is invalid and time counter is read as zero. #1 TOF Time Overflow Flag 1 1 read-only 0 Time overflow has not occurred. #0 1 Time overflow has occurred and time counter is read as zero. #1 TAR RTC Time Alarm Register 0x8 32 read-write n 0x0 0x0 TAR Time Alarm Register 0 32 read-write TCR RTC Time Compensation Register 0xC 32 read-write n 0x0 0x0 CIC Compensation Interval Counter 24 8 read-only CIR Compensation Interval Register 8 8 read-write TCR Time Compensation Register 0 8 read-write 0 Time Prescaler Register overflows every 32768 clock cycles. #0 1 Time Prescaler Register overflows every 32767 clock cycles. #1 10000000 Time Prescaler Register overflows every 32896 clock cycles. #10000000 1111111 Time Prescaler Register overflows every 32641 clock cycles. #1111111 11111111 Time Prescaler Register overflows every 32769 clock cycles. #11111111 TCV Time Compensation Value 16 8 read-only TPR RTC Time Prescaler Register 0x4 32 read-write n 0x0 0x0 TPR Time Prescaler Register 0 16 read-write TSR RTC Time Seconds Register 0x0 32 read-write n 0x0 0x0 TSR Time Seconds Register 0 32 read-write WAR RTC Write Access Register 0x800 32 read-write n 0x0 0x0 CRW Control Register Write 4 1 read-write 0 Writes to the Control Register are ignored. #0 1 Writes to the Control Register complete as normal. #1 IERW Interrupt Enable Register Write 7 1 read-write 0 Writes to the Interupt Enable Register are ignored. #0 1 Writes to the Interrupt Enable Register complete as normal. #1 LRW Lock Register Write 6 1 read-write 0 Writes to the Lock Register are ignored. #0 1 Writes to the Lock Register complete as normal. #1 SRW Status Register Write 5 1 read-write 0 Writes to the Status Register are ignored. #0 1 Writes to the Status Register complete as normal. #1 TARW Time Alarm Register Write 2 1 read-write 0 Writes to the Time Alarm Register are ignored. #0 1 Writes to the Time Alarm Register complete as normal. #1 TCRW Time Compensation Register Write 3 1 read-write 0 Writes to the Time Compensation Register are ignored. #0 1 Writes to the Time Compensation Register complete as normal. #1 TPRW Time Prescaler Register Write 1 1 read-write 0 Writes to the Time Prescaler Register are ignored. #0 1 Writes to the Time Prescaler Register complete as normal. #1 TSRW Time Seconds Register Write 0 1 read-write 0 Writes to the Time Seconds Register are ignored. #0 1 Writes to the Time Seconds Register complete as normal. #1 SIM System Integration Module SIM 0x0 0x0 0x1064 registers n CLKDIV1 System Clock Divider Register 1 0x1044 32 read-write n 0x0 0x0 OUTDIV1 Clock 1 output divider value 28 4 read-write 0000 Divide-by-1. #0000 0001 Divide-by-2. #0001 0010 Divide-by-3. #0010 0011 Divide-by-4. #0011 0100 Divide-by-5. #0100 0101 Divide-by-6. #0101 0110 Divide-by-7. #0110 0111 Divide-by-8. #0111 1000 Divide-by-9. #1000 1001 Divide-by-10. #1001 1010 Divide-by-11. #1010 1011 Divide-by-12. #1011 1100 Divide-by-13. #1100 1101 Divide-by-14. #1101 1110 Divide-by-15. #1110 1111 Divide-by-16. #1111 OUTDIV2 Clock 2 output divider value 24 4 read-write 0000 Divide-by-1. #0000 0001 Divide-by-2. #0001 0010 Divide-by-3. #0010 0011 Divide-by-4. #0011 0100 Divide-by-5. #0100 0101 Divide-by-6. #0101 0110 Divide-by-7. #0110 0111 Divide-by-8. #0111 1000 Divide-by-9. #1000 1001 Divide-by-10. #1001 1010 Divide-by-11. #1010 1011 Divide-by-12. #1011 1100 Divide-by-13. #1100 1101 Divide-by-14. #1101 1110 Divide-by-15. #1110 1111 Divide-by-16. #1111 OUTDIV3 Clock 3 output divider value 20 4 read-write 0000 Divide-by-1. #0000 0001 Divide-by-2. #0001 0010 Divide-by-3. #0010 0011 Divide-by-4. #0011 0100 Divide-by-5. #0100 0101 Divide-by-6. #0101 0110 Divide-by-7. #0110 0111 Divide-by-8. #0111 1000 Divide-by-9. #1000 1001 Divide-by-10. #1001 1010 Divide-by-11. #1010 1011 Divide-by-12. #1011 1100 Divide-by-13. #1100 1101 Divide-by-14. #1101 1110 Divide-by-15. #1110 1111 Divide-by-16. #1111 OUTDIV4 Clock 4 output divider value 16 4 read-write 0000 Divide-by-1. #0000 0001 Divide-by-2. #0001 0010 Divide-by-3. #0010 0011 Divide-by-4. #0011 0100 Divide-by-5. #0100 0101 Divide-by-6. #0101 0110 Divide-by-7. #0110 0111 Divide-by-8. #0111 1000 Divide-by-9. #1000 1001 Divide-by-10. #1001 1010 Divide-by-11. #1010 1011 Divide-by-12. #1011 1100 Divide-by-13. #1100 1101 Divide-by-14. #1101 1110 Divide-by-15. #1110 1111 Divide-by-16. #1111 CLKDIV2 System Clock Divider Register 2 0x1048 32 read-write n 0x0 0x0 USBDIV USB clock divider divisor 1 3 read-write USBFRAC USB clock divider fraction 0 1 read-write FCFG1 Flash Configuration Register 1 0x104C 32 read-write n 0x0 0x0 FLASHDIS Flash Disable 0 1 read-write 0 Flash is enabled #0 1 Flash is disabled #1 FLASHDOZE Flash Doze 1 1 read-write 0 Flash remains enabled during Wait mode #0 1 Flash is disabled for the duration of Wait mode #1 PFSIZE Program flash size 24 4 read-only 0011 32 KB of program flash memory #0011 0101 64 KB of program flash memory #0101 0111 128 KB of program flash memory #0111 1001 256 KB of program flash memory #1001 1011 512 KB of program flash memory #1011 1101 1024 KB of program flash memory #1101 1111 512 KB of program flash memory #1111 FCFG2 Flash Configuration Register 2 0x1050 32 read-only n 0x0 0x0 MAXADDR0 Max address block 0 24 7 read-only MAXADDR1 Max address block 1 16 7 read-only SCGC4 System Clock Gating Control Register 4 0x1034 32 read-write n 0x0 0x0 CMP Comparator Clock Gate Control 19 1 read-write 0 Clock disabled #0 1 Clock enabled #1 EWM EWM Clock Gate Control 1 1 read-write 0 Clock disabled #0 1 Clock enabled #1 I2C0 I2C0 Clock Gate Control 6 1 read-write 0 Clock disabled #0 1 Clock enabled #1 I2C1 I2C1 Clock Gate Control 7 1 read-write 0 Clock disabled #0 1 Clock enabled #1 UART0 UART0 Clock Gate Control 10 1 read-write 0 Clock disabled #0 1 Clock enabled #1 UART1 UART1 Clock Gate Control 11 1 read-write 0 Clock disabled #0 1 Clock enabled #1 UART2 UART2 Clock Gate Control 12 1 read-write 0 Clock disabled #0 1 Clock enabled #1 USBOTG USB Clock Gate Control 18 1 read-write 0 Clock disabled #0 1 Clock enabled #1 VREF VREF Clock Gate Control 20 1 read-write 0 Clock disabled #0 1 Clock enabled #1 SCGC5 System Clock Gating Control Register 5 0x1038 32 read-write n 0x0 0x0 LPTMR Low Power Timer Access Control 0 1 read-write 0 Access disabled #0 1 Access enabled #1 PORTA Port A Clock Gate Control 9 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PORTB Port B Clock Gate Control 10 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PORTC Port C Clock Gate Control 11 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PORTD Port D Clock Gate Control 12 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PORTE Port E Clock Gate Control 13 1 read-write 0 Clock disabled #0 1 Clock enabled #1 SCGC6 System Clock Gating Control Register 6 0x103C 32 read-write n 0x0 0x0 ADC0 ADC0 Clock Gate Control 27 1 read-write 0 Clock disabled #0 1 Clock enabled #1 ADC1 ADC1 Clock Gate Control 7 1 read-write 0 Clock disabled #0 1 Clock enabled #1 CRC CRC Clock Gate Control 18 1 read-write 0 Clock disabled #0 1 Clock enabled #1 DAC0 DAC0 Clock Gate Control 31 1 read-write 0 Clock disabled #0 1 Clock enabled #1 DAC1 DAC1 Clock Gate Control 8 1 read-write 0 Clock disabled #0 1 Clock enabled #1 DMAMUX DMA Mux Clock Gate Control 1 1 read-write 0 Clock disabled #0 1 Clock enabled #1 FTF Flash Memory Clock Gate Control 0 1 read-write 0 Clock disabled #0 1 Clock enabled #1 FTM0 FTM0 Clock Gate Control 24 1 read-write 0 Clock disabled #0 1 Clock enabled #1 FTM1 FTM1 Clock Gate Control 25 1 read-write 0 Clock disabled #0 1 Clock enabled #1 FTM2 FTM2 Clock Gate Control 26 1 read-write 0 Clock disabled #0 1 Clock enabled #1 FTM3 FTM3 Clock Gate Control 6 1 read-write 0 Clock disabled #0 1 Clock enabled #1 I2S I2S Clock Gate Control 15 1 read-write 0 Clock disabled #0 1 Clock enabled #1 LPUART0 LPUART0 Clock Gate Control 10 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PDB PDB Clock Gate Control 22 1 read-write 0 Clock disabled #0 1 Clock enabled #1 PIT PIT Clock Gate Control 23 1 read-write 0 Clock disabled #0 1 Clock enabled #1 RNGA RNGA Clock Gate Control 9 1 read-write RTC RTC Access Control 29 1 read-write 0 Access and interrupts disabled #0 1 Access and interrupts enabled #1 SPI0 SPI0 Clock Gate Control 12 1 read-write 0 Clock disabled #0 1 Clock enabled #1 SPI1 SPI1 Clock Gate Control 13 1 read-write 0 Clock disabled #0 1 Clock enabled #1 SCGC7 System Clock Gating Control Register 7 0x1040 32 read-write n 0x0 0x0 DMA DMA Clock Gate Control 1 1 read-write 0 Clock disabled #0 1 Clock enabled #1 FLEXBUS FlexBus Clock Gate Control 0 1 read-write 0 Clock disabled #0 1 Clock enabled #1 SDID System Device Identification Register 0x1024 32 read-only n 0x0 0x0 DIEID Device Die ID 7 5 read-only FAMID Kinetis family identification 4 3 read-only 000 K1x Family (without tamper) #000 001 K2x Family (without tamper) #001 010 K3x Family or K1x/K6x Family (with tamper) #010 011 K4x Family or K2x Family (with tamper) #011 100 K6x Family (without tamper) #100 101 K7x Family #101 FAMILYID Kinetis Family ID 28 4 read-only 0001 K1x Family #0001 0010 K2x Family #0010 0011 K3x Family #0011 0100 K4x Family #0100 0110 K6x Family #0110 0111 K7x Family #0111 PINID Pincount identification 0 4 read-only 0010 32-pin #0010 0100 48-pin #0100 0101 64-pin #0101 0110 80-pin #0110 0111 81-pin or 121-pin #0111 1000 100-pin #1000 1001 121-pin #1001 1010 144-pin #1010 1011 Custom pinout (WLCSP) #1011 1100 169-pin #1100 1110 256-pin #1110 REVID Device revision number 12 4 read-only SERIESID Kinetis Series ID 20 4 read-only 0000 Kinetis K series #0000 0001 Kinetis L series #0001 0101 Kinetis W series #0101 0110 Kinetis V series #0110 SUBFAMID Kinetis Sub-Family ID 24 4 read-only 0000 Kx0 Subfamily #0000 0001 Kx1 Subfamily (tamper detect) #0001 0010 Kx2 Subfamily #0010 0011 Kx3 Subfamily (tamper detect) #0011 0100 Kx4 Subfamily #0100 0101 Kx5 Subfamily (tamper detect) #0101 0110 Kx6 Subfamily #0110 SOPT1 System Options Register 1 0x0 32 read-write n 0x0 0x0 OSC32KOUT 32K Oscillator Clock Output 16 2 read-write 00 ERCLK32K is not output. #00 01 ERCLK32K is output on PTE0. #01 10 ERCLK32K is output on PTE26. #10 OSC32KSEL 32K oscillator clock select 18 2 read-write 00 System oscillator (OSC32KCLK) #00 10 RTC 32.768kHz oscillator #10 11 LPO 1 kHz #11 RAMSIZE RAM size 12 4 read-only 0001 8 KB #0001 0011 16 KB #0011 0100 24 KB #0100 0101 32 KB #0101 0110 48 KB #0110 0111 64 KB #0111 1000 96 KB #1000 1001 128 KB #1001 1011 256 KB #1011 USBREGEN USB voltage regulator enable 31 1 read-write 0 USB voltage regulator is disabled. #0 1 USB voltage regulator is enabled. #1 USBSSTBY USB voltage regulator in standby mode during Stop, VLPS, LLS and VLLS modes. 30 1 read-write 0 USB voltage regulator not in standby during Stop, VLPS, LLS and VLLS modes. #0 1 USB voltage regulator in standby during Stop, VLPS, LLS and VLLS modes. #1 USBVSTBY USB voltage regulator in standby mode during VLPR and VLPW modes 29 1 read-write 0 USB voltage regulator not in standby during VLPR and VLPW modes. #0 1 USB voltage regulator in standby during VLPR and VLPW modes. #1 SOPT1CFG SOPT1 Configuration Register 0x4 32 read-write n 0x0 0x0 URWE USB voltage regulator enable write enable 24 1 read-write 0 SOPT1 USBREGEN cannot be written. #0 1 SOPT1 USBREGEN can be written. #1 USSWE USB voltage regulator stop standby write enable 26 1 read-write 0 SOPT1 USBSSTBY cannot be written. #0 1 SOPT1 USBSSTBY can be written. #1 UVSWE USB voltage regulator VLP standby write enable 25 1 read-write 0 SOPT1 USBVSTBY cannot be written. #0 1 SOPT1 USBVSTBY can be written. #1 SOPT2 System Options Register 2 0x1004 32 read-write n 0x0 0x0 CLKOUTSEL CLKOUT select 5 3 read-write 000 FlexBus CLKOUT #000 010 Flash clock #010 011 LPO clock (1 kHz) #011 100 MCGIRCLK #100 101 RTC 32.768kHz clock #101 110 OSCERCLK0 #110 111 IRC 48 MHz clock #111 FBSL FlexBus security level 8 2 read-write 00 All off-chip accesses (instruction and data) via the FlexBus are disallowed. #00 01 All off-chip accesses (instruction and data) via the FlexBus are disallowed. #01 10 Off-chip instruction accesses are disallowed. Data accesses are allowed. #10 11 Off-chip instruction accesses and data accesses are allowed. #11 LPUARTSRC LPUART clock source select 26 2 read-write 00 Clock disabled #00 01 MCGFLLCLK , or MCGPLLCLK , or IRC48M clock as selected by SOPT2[PLLFLLSEL]. #01 10 OSCERCLK clock #10 11 MCGIRCLK clock #11 PLLFLLSEL PLL/FLL clock select 16 2 read-write 00 MCGFLLCLK clock #00 01 MCGPLLCLK clock #01 11 IRC48 MHz clock #11 RTCCLKOUTSEL RTC clock out select 4 1 read-write 0 RTC 1 Hz clock is output on the RTC_CLKOUT pin. #0 1 RTC 32.768kHz clock is output on the RTC_CLKOUT pin. #1 TRACECLKSEL Debug trace clock select 12 1 read-write 0 MCGOUTCLK #0 1 Core/system clock #1 USBSRC USB clock source select 18 1 read-write 0 External bypass clock (USB_CLKIN). #0 1 MCGFLLCLK , or MCGPLLCLK , or IRC48M clock as selected by SOPT2[PLLFLLSEL], and then divided by the USB fractional divider as configured by SIM_CLKDIV2[USBFRAC, USBDIV]. #1 SOPT4 System Options Register 4 0x100C 32 read-write n 0x0 0x0 FTM0CLKSEL FlexTimer 0 External Clock Pin Select 24 1 read-write 0 FTM_CLK0 pin #0 1 FTM_CLK1 pin #1 FTM0FLT0 FTM0 Fault 0 Select 0 1 read-write 0 FTM0_FLT0 pin #0 1 CMP0 out #1 FTM0FLT1 FTM0 Fault 1 Select 1 1 read-write 0 FTM0_FLT1 pin #0 1 CMP1 out #1 FTM0TRG0SRC FlexTimer 0 Hardware Trigger 0 Source Select 28 1 read-write 0 HSCMP0 output drives FTM0 hardware trigger 0 #0 1 FTM1 channel match drives FTM0 hardware trigger 0 #1 FTM0TRG1SRC FlexTimer 0 Hardware Trigger 1 Source Select 29 1 read-write 0 PDB output trigger 1 drives FTM0 hardware trigger 1 #0 1 FTM2 channel match drives FTM0 hardware trigger 1 #1 FTM1CH0SRC FTM1 channel 0 input capture source select 18 2 read-write 00 FTM1_CH0 signal #00 01 CMP0 output #01 10 CMP1 output #10 11 USB start of frame pulse #11 FTM1CLKSEL FTM1 External Clock Pin Select 25 1 read-write 0 FTM_CLK0 pin #0 1 FTM_CLK1 pin #1 FTM1FLT0 FTM1 Fault 0 Select 4 1 read-write 0 FTM1_FLT0 pin #0 1 CMP0 out #1 FTM2CH0SRC FTM2 channel 0 input capture source select 20 2 read-write 00 FTM2_CH0 signal #00 01 CMP0 output #01 10 CMP1 output #10 FTM2CH1SRC FTM2 channel 1 input capture source select 22 1 read-write 0 FTM2_CH1 signal #0 1 Exclusive OR of FTM2_CH1, FTM2_CH0 and FTM1_CH1. #1 FTM2CLKSEL FlexTimer 2 External Clock Pin Select 26 1 read-write 0 FTM2 external clock driven by FTM_CLK0 pin. #0 1 FTM2 external clock driven by FTM_CLK1 pin. #1 FTM2FLT0 FTM2 Fault 0 Select 8 1 read-write 0 FTM2_FLT0 pin #0 1 CMP0 out #1 FTM3CLKSEL FlexTimer 3 External Clock Pin Select 27 1 read-write 0 FTM3 external clock driven by FTM_CLK0 pin. #0 1 FTM3 external clock driven by FTM_CLK1 pin. #1 FTM3FLT0 FTM3 Fault 0 Select 12 1 read-write 0 FTM3_FLT0 pin #0 1 CMP0 out #1 FTM3TRG0SRC FlexTimer 3 Hardware Trigger 0 Source Select 30 1 read-write 1 FTM1 channel match drives FTM3 hardware trigger 0 #1 FTM3TRG1SRC FlexTimer 3 Hardware Trigger 1 Source Select 31 1 read-write 1 FTM2 channel match drives FTM3 hardware trigger 1 #1 SOPT5 System Options Register 5 0x1010 32 read-write n 0x0 0x0 LPUART0RXSRC LPUART0 receive data source select 18 2 read-write 00 LPUART0_RX pin #00 01 CMP0 output #01 10 CMP1 output #10 UART0RXSRC UART 0 receive data source select 2 2 read-write 00 UART0_RX pin #00 01 CMP0 #01 10 CMP1 #10 UART0TXSRC UART 0 transmit data source select 0 2 read-write 00 UART0_TX pin #00 01 UART0_TX pin modulated with FTM1 channel 0 output #01 10 UART0_TX pin modulated with FTM2 channel 0 output #10 UART1RXSRC UART 1 receive data source select 6 2 read-write 00 UART1_RX pin #00 01 CMP0 #01 10 CMP1 #10 UART1TXSRC UART 1 transmit data source select 4 2 read-write 00 UART1_TX pin #00 01 UART1_TX pin modulated with FTM1 channel 0 output #01 10 UART1_TX pin modulated with FTM2 channel 0 output #10 SOPT7 System Options Register 7 0x1018 32 read-write n 0x0 0x0 ADC0ALTTRGEN ADC0 alternate trigger enable 7 1 read-write 0 PDB trigger selected for ADC0. #0 1 Alternate trigger selected for ADC0. #1 ADC0PRETRGSEL ADC0 pretrigger select 4 1 read-write 0 Pre-trigger A #0 1 Pre-trigger B #1 ADC0TRGSEL ADC0 trigger select 0 4 read-write 0000 PDB external trigger pin input (PDB0_EXTRG) #0000 0001 High speed comparator 0 output #0001 0010 High speed comparator 1 output #0010 0100 PIT trigger 0 #0100 0101 PIT trigger 1 #0101 0110 PIT trigger 2 #0110 0111 PIT trigger 3 #0111 1000 FTM0 trigger #1000 1001 FTM1 trigger #1001 1010 FTM2 trigger #1010 1011 FTM3 trigger #1011 1100 RTC alarm #1100 1101 RTC seconds #1101 1110 Low-power timer (LPTMR) trigger #1110 ADC1ALTTRGEN ADC1 alternate trigger enable 15 1 read-write 0 PDB trigger selected for ADC1 #0 1 Alternate trigger selected for ADC1 as defined by ADC1TRGSEL. #1 ADC1PRETRGSEL ADC1 pre-trigger select 12 1 read-write 0 Pre-trigger A selected for ADC1. #0 1 Pre-trigger B selected for ADC1. #1 ADC1TRGSEL ADC1 trigger select 8 4 read-write 0000 PDB external trigger pin input (PDB0_EXTRG) #0000 0001 High speed comparator 0 output #0001 0010 High speed comparator 1 output #0010 0100 PIT trigger 0 #0100 0101 PIT trigger 1 #0101 0110 PIT trigger 2 #0110 0111 PIT trigger 3 #0111 1000 FTM0 trigger #1000 1001 FTM1 trigger #1001 1010 FTM2 trigger #1010 1011 FTM3 trigger #1011 1100 RTC alarm #1100 1101 RTC seconds #1101 1110 Low-power timer (LPTMR) trigger #1110 SOPT8 System Options Register 8 0x101C 32 read-write n 0x0 0x0 FTM0OCH0SRC FTM0 channel 0 output source 16 1 read-write 0 FTM0_CH0 pin is output of FTM0 channel 0 output #0 1 FTM0_CH0 pin is output of FTM0 channel 0 output, modulated by FTM1 channel 1 output #1 FTM0OCH1SRC FTM0 channel 1 output source 17 1 read-write 0 FTM0_CH1 pin is output of FTM0 channel 1 output #0 1 FTM0_CH1 pin is output of FTM0 channel 1 output, modulated by FTM1 channel 1 output #1 FTM0OCH2SRC FTM0 channel 2 output source 18 1 read-write 0 FTM0_CH2 pin is output of FTM0 channel 2 output #0 1 FTM0_CH2 pin is output of FTM0 channel 2 output, modulated by FTM1 channel 1 output #1 FTM0OCH3SRC FTM0 channel 3 output source 19 1 read-write 0 FTM0_CH3 pin is output of FTM0 channel 3 output #0 1 FTM0_CH3 pin is output of FTM0 channel 3 output, modulated by FTM1 channel 1 output #1 FTM0OCH4SRC FTM0 channel 4 output source 20 1 read-write 0 FTM0_CH4 pin is output of FTM0 channel 4 output #0 1 FTM0_CH4 pin is output of FTM0 channel 4 output, modulated by FTM1 channel 1 output #1 FTM0OCH5SRC FTM0 channel 5 output source 21 1 read-write 0 FTM0_CH5 pin is output of FTM0 channel 5 output #0 1 FTM0_CH5 pin is output of FTM0 channel 5 output, modulated by FTM1 channel 1 output #1 FTM0OCH6SRC FTM0 channel 6 output source 22 1 read-write 0 FTM0_CH6 pin is output of FTM0 channel 6 output #0 1 FTM0_CH6 pin is output of FTM0 channel 6 output, modulated by FTM1 channel 1 output #1 FTM0OCH7SRC FTM0 channel 7 output source 23 1 read-write 0 FTM0_CH7 pin is output of FTM0 channel 7 output #0 1 FTM0_CH7 pin is output of FTM0 channel 7 output, modulated by FTM1 channel 1 output #1 FTM0SYNCBIT FTM0 Hardware Trigger 0 Software Synchronization 0 1 read-write 0 No effect #0 1 Write 1 to assert the TRIG0 input to FTM0, software must clear this bit to allow other trigger sources to assert. #1 FTM1SYNCBIT FTM1 Hardware Trigger 0 Software Synchronization 1 1 read-write 0 No effect. #0 1 Write 1 to assert the TRIG0 input to FTM1, software must clear this bit to allow other trigger sources to assert. #1 FTM2SYNCBIT FTM2 Hardware Trigger 0 Software Synchronization 2 1 read-write 0 No effect. #0 1 Write 1 to assert the TRIG0 input to FTM2, software must clear this bit to allow other trigger sources to assert. #1 FTM3OCH0SRC FTM3 channel 0 output source 24 1 read-write 0 FTM3_CH0 pin is output of FTM3 channel 0 output #0 1 FTM3_CH0 pin is output of FTM3 channel 0 output modulated by FTM2 channel 1 output. #1 FTM3OCH1SRC FTM3 channel 1 output source 25 1 read-write 0 FTM3_CH1 pin is output of FTM3 channel 1 output #0 1 FTM3_CH1 pin is output of FTM3 channel 1 output modulated by FTM2 channel 1 output. #1 FTM3OCH2SRC FTM3 channel 2 output source 26 1 read-write 0 FTM3_CH2 pin is output of FTM3 channel 2 output #0 1 FTM3_CH2 pin is output of FTM3 channel 2 output modulated by FTM2 channel 1 output. #1 FTM3OCH3SRC FTM3 channel 3 output source 27 1 read-write 0 FTM3_CH3 pin is output of FTM3 channel 3 output #0 1 FTM3_CH3 pin is output of FTM3 channel 3 output modulated by FTM2 channel 1 output. #1 FTM3OCH4SRC FTM3 channel 4 output source 28 1 read-write 0 FTM3_CH4 pin is output of FTM3 channel 4 output #0 1 FTM3_CH4 pin is output of FTM3 channel 4 output modulated by FTM2 channel 1 output. #1 FTM3OCH5SRC FTM3 channel 5 output source 29 1 read-write 0 FTM3_CH5 pin is output of FTM3 channel 5 output #0 1 FTM3_CH5 pin is output of FTM3 channel 5 output modulated by FTM2 channel 1 output. #1 FTM3OCH6SRC FTM3 channel 6 output source 30 1 read-write 0 FTM3_CH6 pin is output of FTM3 channel 6 output #0 1 FTM3_CH6 pin is output of FTM3 channel 6 output modulated by FTM2 channel 1 output. #1 FTM3OCH7SRC FTM3 channel 7 output source 31 1 read-write 0 FTM3_CH7 pin is output of FTM3 channel 7 output #0 1 FTM3_CH7 pin is output of FTM3 channel 7 output modulated by FTM2 channel 1 output. #1 FTM3SYNCBIT FTM3 Hardware Trigger 0 Software Synchronization 3 1 read-write 0 No effect. #0 1 Write 1 to assert the TRIG0 input to FTM3, software must clear this bit to allow other trigger sources to assert. #1 UIDH Unique Identification Register High 0x1054 32 read-only n 0x0 0x0 UID Unique Identification 0 32 read-only UIDL Unique Identification Register Low 0x1060 32 read-only n 0x0 0x0 UID Unique Identification 0 32 read-only UIDMH Unique Identification Register Mid-High 0x1058 32 read-only n 0x0 0x0 UID Unique Identification 0 32 read-only UIDML Unique Identification Register Mid Low 0x105C 32 read-only n 0x0 0x0 UID Unique Identification 0 32 read-only SMC System Mode Controller SMC 0x0 0x0 0x4 registers n PMCTRL Power Mode Control register 0x1 8 read-write n 0x0 0x0 RUNM Run Mode Control 5 2 read-write 00 Normal Run mode (RUN) #00 10 Very-Low-Power Run mode (VLPR) #10 11 High Speed Run mode (HSRUN) #11 STOPA Stop Aborted 3 1 read-only 0 The previous stop mode entry was successsful. #0 1 The previous stop mode entry was aborted. #1 STOPM Stop Mode Control 0 3 read-write 000 Normal Stop (STOP) #000 010 Very-Low-Power Stop (VLPS) #010 011 Low-Leakage Stop (LLSx) #011 100 Very-Low-Leakage Stop (VLLSx) #100 110 Reseved #110 PMPROT Power Mode Protection register 0x0 8 read-write n 0x0 0x0 AHSRUN Allow High Speed Run mode 7 1 read-write 0 HSRUN is not allowed #0 1 HSRUN is allowed #1 ALLS Allow Low-Leakage Stop Mode 3 1 read-write 0 Any LLSx mode is not allowed #0 1 Any LLSx mode is allowed #1 AVLLS Allow Very-Low-Leakage Stop Mode 1 1 read-write 0 Any VLLSx mode is not allowed #0 1 Any VLLSx mode is allowed #1 AVLP Allow Very-Low-Power Modes 5 1 read-write 0 VLPR, VLPW, and VLPS are not allowed. #0 1 VLPR, VLPW, and VLPS are allowed. #1 PMSTAT Power Mode Status register 0x3 8 read-only n 0x0 0x0 PMSTAT When debug is enabled, the PMSTAT will not update to STOP or VLPS When a PSTOP mode is enabled, the PMSTAT will not update to STOP or VLPS 0 8 read-only STOPCTRL Stop Control Register 0x2 8 read-write n 0x0 0x0 LLSM LLS or VLLS Mode Control 0 3 read-write 000 VLLS0 if PMCTRL[STOPM]=VLLSx, LLS2 if PMCTRL[STOPM]=LLSx #000 001 VLLS1 if PMCTRL[STOPM]=VLLSx, LLS2 if PMCTRL[STOPM]=LLSx #001 010 VLLS2 if PMCTRL[STOPM]=VLLSx, LLS2 if PMCTRL[STOPM]=LLSx #010 011 VLLS3 if PMCTRL[STOPM]=VLLSx, LLS3 if PMCTRL[STOPM]=LLSx #011 PORPO POR Power Option 5 1 read-write 0 POR detect circuit is enabled in VLLS0 #0 1 POR detect circuit is disabled in VLLS0 #1 PSTOPO Partial Stop Option 6 2 read-write 00 STOP - Normal Stop mode #00 01 PSTOP1 - Partial Stop with both system and bus clocks disabled #01 10 PSTOP2 - Partial Stop with system clock disabled and bus clock enabled #10 SPI0 Serial Peripheral Interface SPI 0x0 0x0 0x8C registers n SPI0 26 CTAR0 Clock and Transfer Attributes Register (In Master Mode) SPI0 0x18 32 read-write n 0x0 0x0 ASC After SCK Delay Scaler 8 4 read-write BR Baud Rate Scaler 0 4 read-write CPHA Clock Phase 25 1 read-write 0 Data is captured on the leading edge of SCK and changed on the following edge. #0 1 Data is changed on the leading edge of SCK and captured on the following edge. #1 CPOL Clock Polarity 26 1 read-write 0 The inactive state value of SCK is low. #0 1 The inactive state value of SCK is high. #1 CSSCK PCS to SCK Delay Scaler 12 4 read-write DBR Double Baud Rate 31 1 read-write 0 The baud rate is computed normally with a 50/50 duty cycle. #0 1 The baud rate is doubled with the duty cycle depending on the Baud Rate Prescaler. #1 DT Delay After Transfer Scaler 4 4 read-write FMSZ Frame Size 27 4 read-write LSBFE LSB First 24 1 read-write 0 Data is transferred MSB first. #0 1 Data is transferred LSB first. #1 PASC After SCK Delay Prescaler 20 2 read-write 00 Delay after Transfer Prescaler value is 1. #00 01 Delay after Transfer Prescaler value is 3. #01 10 Delay after Transfer Prescaler value is 5. #10 11 Delay after Transfer Prescaler value is 7. #11 PBR Baud Rate Prescaler 16 2 read-write 00 Baud Rate Prescaler value is 2. #00 01 Baud Rate Prescaler value is 3. #01 10 Baud Rate Prescaler value is 5. #10 11 Baud Rate Prescaler value is 7. #11 PCSSCK PCS to SCK Delay Prescaler 22 2 read-write 00 PCS to SCK Prescaler value is 1. #00 01 PCS to SCK Prescaler value is 3. #01 10 PCS to SCK Prescaler value is 5. #10 11 PCS to SCK Prescaler value is 7. #11 PDT Delay after Transfer Prescaler 18 2 read-write 00 Delay after Transfer Prescaler value is 1. #00 01 Delay after Transfer Prescaler value is 3. #01 10 Delay after Transfer Prescaler value is 5. #10 11 Delay after Transfer Prescaler value is 7. #11 CTAR1 Clock and Transfer Attributes Register (In Master Mode) SPI0 0x28 32 read-write n 0x0 0x0 ASC After SCK Delay Scaler 8 4 read-write BR Baud Rate Scaler 0 4 read-write CPHA Clock Phase 25 1 read-write 0 Data is captured on the leading edge of SCK and changed on the following edge. #0 1 Data is changed on the leading edge of SCK and captured on the following edge. #1 CPOL Clock Polarity 26 1 read-write 0 The inactive state value of SCK is low. #0 1 The inactive state value of SCK is high. #1 CSSCK PCS to SCK Delay Scaler 12 4 read-write DBR Double Baud Rate 31 1 read-write 0 The baud rate is computed normally with a 50/50 duty cycle. #0 1 The baud rate is doubled with the duty cycle depending on the Baud Rate Prescaler. #1 DT Delay After Transfer Scaler 4 4 read-write FMSZ Frame Size 27 4 read-write LSBFE LSB First 24 1 read-write 0 Data is transferred MSB first. #0 1 Data is transferred LSB first. #1 PASC After SCK Delay Prescaler 20 2 read-write 00 Delay after Transfer Prescaler value is 1. #00 01 Delay after Transfer Prescaler value is 3. #01 10 Delay after Transfer Prescaler value is 5. #10 11 Delay after Transfer Prescaler value is 7. #11 PBR Baud Rate Prescaler 16 2 read-write 00 Baud Rate Prescaler value is 2. #00 01 Baud Rate Prescaler value is 3. #01 10 Baud Rate Prescaler value is 5. #10 11 Baud Rate Prescaler value is 7. #11 PCSSCK PCS to SCK Delay Prescaler 22 2 read-write 00 PCS to SCK Prescaler value is 1. #00 01 PCS to SCK Prescaler value is 3. #01 10 PCS to SCK Prescaler value is 5. #10 11 PCS to SCK Prescaler value is 7. #11 PDT Delay after Transfer Prescaler 18 2 read-write 00 Delay after Transfer Prescaler value is 1. #00 01 Delay after Transfer Prescaler value is 3. #01 10 Delay after Transfer Prescaler value is 5. #10 11 Delay after Transfer Prescaler value is 7. #11 CTAR_SLAVE Clock and Transfer Attributes Register (In Slave Mode) SPI0 0xC 32 read-write n 0x0 0x0 CPHA Clock Phase 25 1 read-write 0 Data is captured on the leading edge of SCK and changed on the following edge. #0 1 Data is changed on the leading edge of SCK and captured on the following edge. #1 CPOL Clock Polarity 26 1 read-write 0 The inactive state value of SCK is low. #0 1 The inactive state value of SCK is high. #1 FMSZ Frame Size 27 5 read-write MCR Module Configuration Register 0x0 32 read-write n 0x0 0x0 CLR_RXF Flushes the RX FIFO 10 1 write-only 0 Do not clear the RX FIFO counter. #0 1 Clear the RX FIFO counter. #1 CLR_TXF Clear TX FIFO 11 1 write-only 0 Do not clear the TX FIFO counter. #0 1 Clear the TX FIFO counter. #1 CONT_SCKE Continuous SCK Enable 30 1 read-write 0 Continuous SCK disabled. #0 1 Continuous SCK enabled. #1 DCONF SPI Configuration. 28 2 read-only 00 SPI #00 DIS_RXF Disable Receive FIFO 12 1 read-write 0 RX FIFO is enabled. #0 1 RX FIFO is disabled. #1 DIS_TXF Disable Transmit FIFO 13 1 read-write 0 TX FIFO is enabled. #0 1 TX FIFO is disabled. #1 DOZE Doze Enable 15 1 read-write 0 Doze mode has no effect on the module. #0 1 Doze mode disables the module. #1 FRZ Freeze 27 1 read-write 0 Do not halt serial transfers in Debug mode. #0 1 Halt serial transfers in Debug mode. #1 HALT Halt 0 1 read-write 0 Start transfers. #0 1 Stop transfers. #1 MDIS Module Disable 14 1 read-write 0 Enables the module clocks. #0 1 Allows external logic to disable the module clocks. #1 MSTR Master/Slave Mode Select 31 1 read-write 0 Enables Slave mode #0 1 Enables Master mode #1 MTFE Modified Timing Format Enable 26 1 read-write 0 Modified SPI transfer format disabled. #0 1 Modified SPI transfer format enabled. #1 PCSIS Peripheral Chip Select x Inactive State 16 6 read-write 0 The inactive state of PCSx is low. #0 1 The inactive state of PCSx is high. #1 PCSIS0 Peripheral Chip Select x Inactive State 16 1 read-write 0 The inactive state of PCSx is low. #0 1 The inactive state of PCSx is high. #1 PCSIS1 Peripheral Chip Select x Inactive State 17 1 read-write 0 The inactive state of PCSx is low. #0 1 The inactive state of PCSx is high. #1 PCSIS2 Peripheral Chip Select x Inactive State 18 1 read-write 0 The inactive state of PCSx is low. #0 1 The inactive state of PCSx is high. #1 PCSIS3 Peripheral Chip Select x Inactive State 19 1 read-write 0 The inactive state of PCSx is low. #0 1 The inactive state of PCSx is high. #1 PCSIS4 Peripheral Chip Select x Inactive State 20 1 read-write 0 The inactive state of PCSx is low. #0 1 The inactive state of PCSx is high. #1 PCSIS5 Peripheral Chip Select x Inactive State 21 1 read-write 0 The inactive state of PCSx is low. #0 1 The inactive state of PCSx is high. #1 PCSSE Peripheral Chip Select Strobe Enable 25 1 read-write 0 PCS5/ PCSS is used as the Peripheral Chip Select[5] signal. #0 1 PCS5/ PCSS is used as an active-low PCS Strobe signal. #1 ROOE Receive FIFO Overflow Overwrite Enable 24 1 read-write 0 Incoming data is ignored. #0 1 Incoming data is shifted into the shift register. #1 SMPL_PT Sample Point 8 2 read-write 00 0 protocol clock cycles between SCK edge and SIN sample #00 01 1 protocol clock cycle between SCK edge and SIN sample #01 10 2 protocol clock cycles between SCK edge and SIN sample #10 POPR POP RX FIFO Register 0x38 32 read-only n 0x0 0x0 RXDATA Received Data 0 32 read-only PUSHR PUSH TX FIFO Register In Master Mode SPI0 0x34 32 read-write n 0x0 0x0 CONT Continuous Peripheral Chip Select Enable 31 1 read-write 0 Return PCSn signals to their inactive state between transfers. #0 1 Keep PCSn signals asserted between transfers. #1 CTAS Clock and Transfer Attributes Select 28 3 read-write 000 CTAR0 #000 001 CTAR1 #001 CTCNT Clear Transfer Counter 26 1 read-write 0 Do not clear the TCR[TCNT] field. #0 1 Clear the TCR[TCNT] field. #1 EOQ End Of Queue 27 1 read-write 0 The SPI data is not the last data to transfer. #0 1 The SPI data is the last data to transfer. #1 PCS Select which PCS signals are to be asserted for the transfer 16 6 read-write 0 Negate the PCS[x] signal. #0 1 Assert the PCS[x] signal. #1 PCS0 Select which PCS signals are to be asserted for the transfer 16 1 read-write 0 Negate the PCS[x] signal. #0 1 Assert the PCS[x] signal. #1 PCS1 Select which PCS signals are to be asserted for the transfer 17 1 read-write 0 Negate the PCS[x] signal. #0 1 Assert the PCS[x] signal. #1 PCS2 Select which PCS signals are to be asserted for the transfer 18 1 read-write 0 Negate the PCS[x] signal. #0 1 Assert the PCS[x] signal. #1 PCS3 Select which PCS signals are to be asserted for the transfer 19 1 read-write 0 Negate the PCS[x] signal. #0 1 Assert the PCS[x] signal. #1 PCS4 Select which PCS signals are to be asserted for the transfer 20 1 read-write 0 Negate the PCS[x] signal. #0 1 Assert the PCS[x] signal. #1 PCS5 Select which PCS signals are to be asserted for the transfer 21 1 read-write 0 Negate the PCS[x] signal. #0 1 Assert the PCS[x] signal. #1 TXDATA Transmit Data 0 16 read-write PUSHR_SLAVE PUSH TX FIFO Register In Slave Mode SPI0 0x34 32 read-write n 0x0 0x0 TXDATA Transmit Data 0 32 read-write RSER DMA/Interrupt Request Select and Enable Register 0x30 32 read-write n 0x0 0x0 EOQF_RE Finished Request Enable 28 1 read-write 0 EOQF interrupt requests are disabled. #0 1 EOQF interrupt requests are enabled. #1 RFDF_DIRS Receive FIFO Drain DMA or Interrupt Request Select 16 1 read-write 0 Interrupt request. #0 1 DMA request. #1 RFDF_RE Receive FIFO Drain Request Enable 17 1 read-write 0 RFDF interrupt or DMA requests are disabled. #0 1 RFDF interrupt or DMA requests are enabled. #1 RFOF_RE Receive FIFO Overflow Request Enable 19 1 read-write 0 RFOF interrupt requests are disabled. #0 1 RFOF interrupt requests are enabled. #1 TCF_RE Transmission Complete Request Enable 31 1 read-write 0 TCF interrupt requests are disabled. #0 1 TCF interrupt requests are enabled. #1 TFFF_DIRS Transmit FIFO Fill DMA or Interrupt Request Select 24 1 read-write 0 TFFF flag generates interrupt requests. #0 1 TFFF flag generates DMA requests. #1 TFFF_RE Transmit FIFO Fill Request Enable 25 1 read-write 0 TFFF interrupts or DMA requests are disabled. #0 1 TFFF interrupts or DMA requests are enabled. #1 TFUF_RE Transmit FIFO Underflow Request Enable 27 1 read-write 0 TFUF interrupt requests are disabled. #0 1 TFUF interrupt requests are enabled. #1 RXFR0 Receive FIFO Registers 0xF8 32 read-only n 0x0 0x0 RXDATA Receive Data 0 32 read-only RXFR1 Receive FIFO Registers 0x178 32 read-only n 0x0 0x0 RXDATA Receive Data 0 32 read-only RXFR2 Receive FIFO Registers 0x1FC 32 read-only n 0x0 0x0 RXDATA Receive Data 0 32 read-only RXFR3 Receive FIFO Registers 0x284 32 read-only n 0x0 0x0 RXDATA Receive Data 0 32 read-only SR Status Register 0x2C 32 read-write n 0x0 0x0 EOQF End of Queue Flag 28 1 read-write 0 EOQ is not set in the executing command. #0 1 EOQ is set in the executing SPI command. #1 POPNXTPTR Pop Next Pointer 0 4 read-only RFDF Receive FIFO Drain Flag 17 1 read-write 0 RX FIFO is empty. #0 1 RX FIFO is not empty. #1 RFOF Receive FIFO Overflow Flag 19 1 read-write 0 No Rx FIFO overflow. #0 1 Rx FIFO overflow has occurred. #1 RXCTR RX FIFO Counter 4 4 read-only TCF Transfer Complete Flag 31 1 read-write 0 Transfer not complete. #0 1 Transfer complete. #1 TFFF Transmit FIFO Fill Flag 25 1 read-write 0 TX FIFO is full. #0 1 TX FIFO is not full. #1 TFUF Transmit FIFO Underflow Flag 27 1 read-write 0 No TX FIFO underflow. #0 1 TX FIFO underflow has occurred. #1 TXCTR TX FIFO Counter 12 4 read-only TXNXTPTR Transmit Next Pointer 8 4 read-only TXRXS TX and RX Status 30 1 read-write 0 Transmit and receive operations are disabled (The module is in Stopped state). #0 1 Transmit and receive operations are enabled (The module is in Running state). #1 TCR Transfer Count Register 0x8 32 read-write n 0x0 0x0 SPI_TCNT SPI Transfer Counter 16 16 read-write TXFR0 Transmit FIFO Registers 0x78 32 read-only n 0x0 0x0 TXCMD_TXDATA Transmit Command or Transmit Data 16 16 read-only TXDATA Transmit Data 0 16 read-only TXFR1 Transmit FIFO Registers 0xB8 32 read-only n 0x0 0x0 TXCMD_TXDATA Transmit Command or Transmit Data 16 16 read-only TXDATA Transmit Data 0 16 read-only TXFR2 Transmit FIFO Registers 0xFC 32 read-only n 0x0 0x0 TXCMD_TXDATA Transmit Command or Transmit Data 16 16 read-only TXDATA Transmit Data 0 16 read-only TXFR3 Transmit FIFO Registers 0x144 32 read-only n 0x0 0x0 TXCMD_TXDATA Transmit Command or Transmit Data 16 16 read-only TXDATA Transmit Data 0 16 read-only SPI1 Serial Peripheral Interface SPI 0x0 0x0 0x8C registers n SPI1 27 CTAR0 Clock and Transfer Attributes Register (In Master Mode) SPI1 0x18 32 read-write n 0x0 0x0 ASC After SCK Delay Scaler 8 4 read-write BR Baud Rate Scaler 0 4 read-write CPHA Clock Phase 25 1 read-write 0 Data is captured on the leading edge of SCK and changed on the following edge. #0 1 Data is changed on the leading edge of SCK and captured on the following edge. #1 CPOL Clock Polarity 26 1 read-write 0 The inactive state value of SCK is low. #0 1 The inactive state value of SCK is high. #1 CSSCK PCS to SCK Delay Scaler 12 4 read-write DBR Double Baud Rate 31 1 read-write 0 The baud rate is computed normally with a 50/50 duty cycle. #0 1 The baud rate is doubled with the duty cycle depending on the Baud Rate Prescaler. #1 DT Delay After Transfer Scaler 4 4 read-write FMSZ Frame Size 27 4 read-write LSBFE LSB First 24 1 read-write 0 Data is transferred MSB first. #0 1 Data is transferred LSB first. #1 PASC After SCK Delay Prescaler 20 2 read-write 00 Delay after Transfer Prescaler value is 1. #00 01 Delay after Transfer Prescaler value is 3. #01 10 Delay after Transfer Prescaler value is 5. #10 11 Delay after Transfer Prescaler value is 7. #11 PBR Baud Rate Prescaler 16 2 read-write 00 Baud Rate Prescaler value is 2. #00 01 Baud Rate Prescaler value is 3. #01 10 Baud Rate Prescaler value is 5. #10 11 Baud Rate Prescaler value is 7. #11 PCSSCK PCS to SCK Delay Prescaler 22 2 read-write 00 PCS to SCK Prescaler value is 1. #00 01 PCS to SCK Prescaler value is 3. #01 10 PCS to SCK Prescaler value is 5. #10 11 PCS to SCK Prescaler value is 7. #11 PDT Delay after Transfer Prescaler 18 2 read-write 00 Delay after Transfer Prescaler value is 1. #00 01 Delay after Transfer Prescaler value is 3. #01 10 Delay after Transfer Prescaler value is 5. #10 11 Delay after Transfer Prescaler value is 7. #11 CTAR1 Clock and Transfer Attributes Register (In Master Mode) SPI1 0x28 32 read-write n 0x0 0x0 ASC After SCK Delay Scaler 8 4 read-write BR Baud Rate Scaler 0 4 read-write CPHA Clock Phase 25 1 read-write 0 Data is captured on the leading edge of SCK and changed on the following edge. #0 1 Data is changed on the leading edge of SCK and captured on the following edge. #1 CPOL Clock Polarity 26 1 read-write 0 The inactive state value of SCK is low. #0 1 The inactive state value of SCK is high. #1 CSSCK PCS to SCK Delay Scaler 12 4 read-write DBR Double Baud Rate 31 1 read-write 0 The baud rate is computed normally with a 50/50 duty cycle. #0 1 The baud rate is doubled with the duty cycle depending on the Baud Rate Prescaler. #1 DT Delay After Transfer Scaler 4 4 read-write FMSZ Frame Size 27 4 read-write LSBFE LSB First 24 1 read-write 0 Data is transferred MSB first. #0 1 Data is transferred LSB first. #1 PASC After SCK Delay Prescaler 20 2 read-write 00 Delay after Transfer Prescaler value is 1. #00 01 Delay after Transfer Prescaler value is 3. #01 10 Delay after Transfer Prescaler value is 5. #10 11 Delay after Transfer Prescaler value is 7. #11 PBR Baud Rate Prescaler 16 2 read-write 00 Baud Rate Prescaler value is 2. #00 01 Baud Rate Prescaler value is 3. #01 10 Baud Rate Prescaler value is 5. #10 11 Baud Rate Prescaler value is 7. #11 PCSSCK PCS to SCK Delay Prescaler 22 2 read-write 00 PCS to SCK Prescaler value is 1. #00 01 PCS to SCK Prescaler value is 3. #01 10 PCS to SCK Prescaler value is 5. #10 11 PCS to SCK Prescaler value is 7. #11 PDT Delay after Transfer Prescaler 18 2 read-write 00 Delay after Transfer Prescaler value is 1. #00 01 Delay after Transfer Prescaler value is 3. #01 10 Delay after Transfer Prescaler value is 5. #10 11 Delay after Transfer Prescaler value is 7. #11 CTAR_SLAVE Clock and Transfer Attributes Register (In Slave Mode) SPI1 0xC 32 read-write n 0x0 0x0 CPHA Clock Phase 25 1 read-write 0 Data is captured on the leading edge of SCK and changed on the following edge. #0 1 Data is changed on the leading edge of SCK and captured on the following edge. #1 CPOL Clock Polarity 26 1 read-write 0 The inactive state value of SCK is low. #0 1 The inactive state value of SCK is high. #1 FMSZ Frame Size 27 5 read-write MCR Module Configuration Register 0x0 32 read-write n 0x0 0x0 CLR_RXF Flushes the RX FIFO 10 1 write-only 0 Do not clear the RX FIFO counter. #0 1 Clear the RX FIFO counter. #1 CLR_TXF Clear TX FIFO 11 1 write-only 0 Do not clear the TX FIFO counter. #0 1 Clear the TX FIFO counter. #1 CONT_SCKE Continuous SCK Enable 30 1 read-write 0 Continuous SCK disabled. #0 1 Continuous SCK enabled. #1 DCONF SPI Configuration. 28 2 read-only 00 SPI #00 DIS_RXF Disable Receive FIFO 12 1 read-write 0 RX FIFO is enabled. #0 1 RX FIFO is disabled. #1 DIS_TXF Disable Transmit FIFO 13 1 read-write 0 TX FIFO is enabled. #0 1 TX FIFO is disabled. #1 DOZE Doze Enable 15 1 read-write 0 Doze mode has no effect on the module. #0 1 Doze mode disables the module. #1 FRZ Freeze 27 1 read-write 0 Do not halt serial transfers in Debug mode. #0 1 Halt serial transfers in Debug mode. #1 HALT Halt 0 1 read-write 0 Start transfers. #0 1 Stop transfers. #1 MDIS Module Disable 14 1 read-write 0 Enables the module clocks. #0 1 Allows external logic to disable the module clocks. #1 MSTR Master/Slave Mode Select 31 1 read-write 0 Enables Slave mode #0 1 Enables Master mode #1 MTFE Modified Timing Format Enable 26 1 read-write 0 Modified SPI transfer format disabled. #0 1 Modified SPI transfer format enabled. #1 PCSIS Peripheral Chip Select x Inactive State 16 6 read-write 0 The inactive state of PCSx is low. #0 1 The inactive state of PCSx is high. #1 PCSIS0 Peripheral Chip Select x Inactive State 16 1 read-write 0 The inactive state of PCSx is low. #0 1 The inactive state of PCSx is high. #1 PCSIS1 Peripheral Chip Select x Inactive State 17 1 read-write 0 The inactive state of PCSx is low. #0 1 The inactive state of PCSx is high. #1 PCSIS2 Peripheral Chip Select x Inactive State 18 1 read-write 0 The inactive state of PCSx is low. #0 1 The inactive state of PCSx is high. #1 PCSIS3 Peripheral Chip Select x Inactive State 19 1 read-write 0 The inactive state of PCSx is low. #0 1 The inactive state of PCSx is high. #1 PCSIS4 Peripheral Chip Select x Inactive State 20 1 read-write 0 The inactive state of PCSx is low. #0 1 The inactive state of PCSx is high. #1 PCSIS5 Peripheral Chip Select x Inactive State 21 1 read-write 0 The inactive state of PCSx is low. #0 1 The inactive state of PCSx is high. #1 PCSSE Peripheral Chip Select Strobe Enable 25 1 read-write 0 PCS5/ PCSS is used as the Peripheral Chip Select[5] signal. #0 1 PCS5/ PCSS is used as an active-low PCS Strobe signal. #1 ROOE Receive FIFO Overflow Overwrite Enable 24 1 read-write 0 Incoming data is ignored. #0 1 Incoming data is shifted into the shift register. #1 SMPL_PT Sample Point 8 2 read-write 00 0 protocol clock cycles between SCK edge and SIN sample #00 01 1 protocol clock cycle between SCK edge and SIN sample #01 10 2 protocol clock cycles between SCK edge and SIN sample #10 POPR POP RX FIFO Register 0x38 32 read-only n 0x0 0x0 RXDATA Received Data 0 32 read-only PUSHR PUSH TX FIFO Register In Master Mode SPI1 0x34 32 read-write n 0x0 0x0 CONT Continuous Peripheral Chip Select Enable 31 1 read-write 0 Return PCSn signals to their inactive state between transfers. #0 1 Keep PCSn signals asserted between transfers. #1 CTAS Clock and Transfer Attributes Select 28 3 read-write 000 CTAR0 #000 001 CTAR1 #001 CTCNT Clear Transfer Counter 26 1 read-write 0 Do not clear the TCR[TCNT] field. #0 1 Clear the TCR[TCNT] field. #1 EOQ End Of Queue 27 1 read-write 0 The SPI data is not the last data to transfer. #0 1 The SPI data is the last data to transfer. #1 PCS Select which PCS signals are to be asserted for the transfer 16 6 read-write 0 Negate the PCS[x] signal. #0 1 Assert the PCS[x] signal. #1 PCS0 Select which PCS signals are to be asserted for the transfer 16 1 read-write 0 Negate the PCS[x] signal. #0 1 Assert the PCS[x] signal. #1 PCS1 Select which PCS signals are to be asserted for the transfer 17 1 read-write 0 Negate the PCS[x] signal. #0 1 Assert the PCS[x] signal. #1 PCS2 Select which PCS signals are to be asserted for the transfer 18 1 read-write 0 Negate the PCS[x] signal. #0 1 Assert the PCS[x] signal. #1 PCS3 Select which PCS signals are to be asserted for the transfer 19 1 read-write 0 Negate the PCS[x] signal. #0 1 Assert the PCS[x] signal. #1 PCS4 Select which PCS signals are to be asserted for the transfer 20 1 read-write 0 Negate the PCS[x] signal. #0 1 Assert the PCS[x] signal. #1 PCS5 Select which PCS signals are to be asserted for the transfer 21 1 read-write 0 Negate the PCS[x] signal. #0 1 Assert the PCS[x] signal. #1 TXDATA Transmit Data 0 16 read-write PUSHR_SLAVE PUSH TX FIFO Register In Slave Mode SPI1 0x34 32 read-write n 0x0 0x0 TXDATA Transmit Data 0 32 read-write RSER DMA/Interrupt Request Select and Enable Register 0x30 32 read-write n 0x0 0x0 EOQF_RE Finished Request Enable 28 1 read-write 0 EOQF interrupt requests are disabled. #0 1 EOQF interrupt requests are enabled. #1 RFDF_DIRS Receive FIFO Drain DMA or Interrupt Request Select 16 1 read-write 0 Interrupt request. #0 1 DMA request. #1 RFDF_RE Receive FIFO Drain Request Enable 17 1 read-write 0 RFDF interrupt or DMA requests are disabled. #0 1 RFDF interrupt or DMA requests are enabled. #1 RFOF_RE Receive FIFO Overflow Request Enable 19 1 read-write 0 RFOF interrupt requests are disabled. #0 1 RFOF interrupt requests are enabled. #1 TCF_RE Transmission Complete Request Enable 31 1 read-write 0 TCF interrupt requests are disabled. #0 1 TCF interrupt requests are enabled. #1 TFFF_DIRS Transmit FIFO Fill DMA or Interrupt Request Select 24 1 read-write 0 TFFF flag generates interrupt requests. #0 1 TFFF flag generates DMA requests. #1 TFFF_RE Transmit FIFO Fill Request Enable 25 1 read-write 0 TFFF interrupts or DMA requests are disabled. #0 1 TFFF interrupts or DMA requests are enabled. #1 TFUF_RE Transmit FIFO Underflow Request Enable 27 1 read-write 0 TFUF interrupt requests are disabled. #0 1 TFUF interrupt requests are enabled. #1 RXFR0 Receive FIFO Registers 0xF8 32 read-only n 0x0 0x0 RXDATA Receive Data 0 32 read-only RXFR1 Receive FIFO Registers 0x178 32 read-only n 0x0 0x0 RXDATA Receive Data 0 32 read-only RXFR2 Receive FIFO Registers 0x1FC 32 read-only n 0x0 0x0 RXDATA Receive Data 0 32 read-only RXFR3 Receive FIFO Registers 0x284 32 read-only n 0x0 0x0 RXDATA Receive Data 0 32 read-only SR Status Register 0x2C 32 read-write n 0x0 0x0 EOQF End of Queue Flag 28 1 read-write 0 EOQ is not set in the executing command. #0 1 EOQ is set in the executing SPI command. #1 POPNXTPTR Pop Next Pointer 0 4 read-only RFDF Receive FIFO Drain Flag 17 1 read-write 0 RX FIFO is empty. #0 1 RX FIFO is not empty. #1 RFOF Receive FIFO Overflow Flag 19 1 read-write 0 No Rx FIFO overflow. #0 1 Rx FIFO overflow has occurred. #1 RXCTR RX FIFO Counter 4 4 read-only TCF Transfer Complete Flag 31 1 read-write 0 Transfer not complete. #0 1 Transfer complete. #1 TFFF Transmit FIFO Fill Flag 25 1 read-write 0 TX FIFO is full. #0 1 TX FIFO is not full. #1 TFUF Transmit FIFO Underflow Flag 27 1 read-write 0 No TX FIFO underflow. #0 1 TX FIFO underflow has occurred. #1 TXCTR TX FIFO Counter 12 4 read-only TXNXTPTR Transmit Next Pointer 8 4 read-only TXRXS TX and RX Status 30 1 read-write 0 Transmit and receive operations are disabled (The module is in Stopped state). #0 1 Transmit and receive operations are enabled (The module is in Running state). #1 TCR Transfer Count Register 0x8 32 read-write n 0x0 0x0 SPI_TCNT SPI Transfer Counter 16 16 read-write TXFR0 Transmit FIFO Registers 0x78 32 read-only n 0x0 0x0 TXCMD_TXDATA Transmit Command or Transmit Data 16 16 read-only TXDATA Transmit Data 0 16 read-only TXFR1 Transmit FIFO Registers 0xB8 32 read-only n 0x0 0x0 TXCMD_TXDATA Transmit Command or Transmit Data 16 16 read-only TXDATA Transmit Data 0 16 read-only TXFR2 Transmit FIFO Registers 0xFC 32 read-only n 0x0 0x0 TXCMD_TXDATA Transmit Command or Transmit Data 16 16 read-only TXDATA Transmit Data 0 16 read-only TXFR3 Transmit FIFO Registers 0x144 32 read-only n 0x0 0x0 TXCMD_TXDATA Transmit Command or Transmit Data 16 16 read-only TXDATA Transmit Data 0 16 read-only SystemControl System Control Block SystemControl 0x0 0x8 0xF38 registers n SCB_ACTLR Auxiliary Control Register, 0x8 32 read-write n 0x0 0x0 DISDEFWBUF Disables write buffer use during default memory map accesses. 1 1 read-write DISFOLD Disables folding of IT instructions. 2 1 read-write DISMCYCINT Disables interruption of multi-cycle instructions. 0 1 read-write SCB_AFSR Auxiliary Fault Status Register 0xD3C 32 read-write n 0x0 0x0 AUXFAULT Latched version of the AUXFAULT inputs 0 32 read-write SCB_AIRCR Application Interrupt and Reset Control Register 0xD0C 32 read-write n 0x0 0x0 ENDIANNESS no description available 15 1 read-only 0 Little-endian #0 1 Big-endian #1 PRIGROUP Interrupt priority grouping field. This field determines the split of group priority from subpriority. 8 3 read-write SYSRESETREQ no description available 2 1 write-only 0 no system reset request #0 1 asserts a signal to the outer system that requests a reset #1 VECTCLRACTIVE no description available 1 1 write-only VECTKEY Register key 16 16 read-write VECTRESET no description available 0 1 write-only SCB_BFAR BusFault Address Register 0xD38 32 read-write n 0x0 0x0 ADDRESS Address of the BusFault location 0 32 read-write SCB_CCR Configuration and Control Register 0xD14 32 read-write n 0x0 0x0 BFHFNMIGN Enables handlers with priority -1 or -2 to ignore data BusFaults caused by load and store instructions. 8 1 read-write 0 data bus faults caused by load and store instructions cause a lock-up #0 1 handlers running at priority -1 and -2 ignore data bus faults caused by load and store instructions #1 DIV_0_TRP Enables faulting or halting when the processor executes an SDIV or UDIV instruction with a divisor of 0 4 1 read-write 0 do not trap divide by 0 #0 1 trap divide by 0 #1 NONBASETHRDENA no description available 0 1 read-write 0 processor can enter Thread mode only when no exception is active #0 1 processor can enter Thread mode from any level under the control of an EXC_RETURN value #1 STKALIGN Indicates stack alignment on exception entry 9 1 read-write 0 4-byte aligned #0 1 8-byte aligned #1 UNALIGN_TRP Enables unaligned access traps 3 1 read-write 0 do not trap unaligned halfword and word accesses #0 1 trap unaligned halfword and word accesses #1 USERSETMPEND Enables unprivileged software access to the STIR 1 1 read-write 0 disable #0 1 enable #1 SCB_CFSR Configurable Fault Status Registers 0xD28 32 read-write n 0x0 0x0 BFARVALID no description available 15 1 read-write 0 value in BFAR is not a valid fault address #0 1 BFAR holds a valid fault address #1 DACCVIOL no description available 1 1 read-write 0 no data access violation fault #0 1 the processor attempted a load or store at a location that does not permit the operation #1 DIVBYZERO no description available 25 1 read-write 0 no divide by zero fault, or divide by zero trapping not enabled #0 1 the processor has executed an SDIV or UDIV instruction with a divisor of 0 #1 IACCVIOL no description available 0 1 read-write 0 no instruction access violation fault #0 1 the processor attempted an instruction fetch from a location that does not permit execution #1 IBUSERR no description available 8 1 read-write 0 no instruction bus error #0 1 instruction bus error #1 IMPRECISERR no description available 10 1 read-write 0 no imprecise data bus error #0 1 a data bus error has occurred, but the return address in the stack frame is not related to the instruction that caused the error #1 INVPC no description available 18 1 read-write 0 no invalid PC load UsageFault #0 1 the processor has attempted an illegal load of EXC_RETURN to the PC #1 INVSTATE no description available 17 1 read-write 0 no invalid state UsageFault #0 1 the processor has attempted to execute an instruction that makes illegal use of the EPSR #1 LSPERR no description available 13 1 read-write 0 No bus fault occurred during floating-point lazy state preservation #0 1 A bus fault occurred during floating-point lazy state preservation #1 MLSPERR no description available 5 1 read-write 0 No MemManage fault occurred during floating-point lazy state preservation #0 1 A MemManage fault occurred during floating-point lazy state preservation #1 MMARVALID no description available 7 1 read-write 0 value in MMAR is not a valid fault address #0 1 MMAR holds a valid fault address #1 MSTKERR no description available 4 1 read-write 0 no stacking fault #0 1 stacking for an exception entry has caused one or more access violations #1 MUNSTKERR no description available 3 1 read-write 0 no unstacking fault #0 1 unstack for an exception return has caused one or more access violations #1 NOCP no description available 19 1 read-write 0 no UsageFault caused by attempting to access a coprocessor #0 1 the processor has attempted to access a coprocessor #1 PRECISERR no description available 9 1 read-write 0 no precise data bus error #0 1 a data bus error has occurred, and the PC value stacked for the exception return points to the instruction that caused the fault #1 STKERR no description available 12 1 read-write 0 no stacking fault #0 1 stacking for an exception entry has caused one or more BusFaults #1 UNALIGNED no description available 24 1 read-write 0 no unaligned access fault, or unaligned access trapping not enabled #0 1 the processor has made an unaligned memory access #1 UNDEFINSTR no description available 16 1 read-write 0 no undefined instruction UsageFault #0 1 the processor has attempted to execute an undefined instruction #1 UNSTKERR no description available 11 1 read-write 0 no unstacking fault #0 1 unstack for an exception return has caused one or more BusFaults #1 SCB_CPACR Coprocessor Access Control Register 0xD88 32 read-write n 0x0 0x0 CP10 Access privileges for coprocessor 10. 20 2 read-write 00 Access denied. Any attempted access generates a NOCP UsageFault #00 01 Privileged access only. An unprivileged access generates a NOCP fault. #01 10 Reserved. The result of any access is UNPREDICTABLE. #10 11 Full access. #11 CP11 Access privileges for coprocessor 11. 22 2 read-write 00 Access denied. Any attempted access generates a NOCP UsageFault #00 01 Privileged access only. An unprivileged access generates a NOCP fault. #01 10 Reserved. The result of any access is UNPREDICTABLE. #10 11 Full access. #11 SCB_CPUID CPUID Base Register 0xD00 32 read-only n 0x0 0x0 IMPLEMENTER Implementer code 24 8 read-only PARTNO Indicates part number 4 12 read-only REVISION Indicates patch release: 0x0 = Patch 0 0 4 read-only VARIANT Indicates processor revision: 0x2 = Revision 2 20 4 read-only SCB_DFSR Debug Fault Status Register 0xD30 32 read-write n 0x0 0x0 BKPT no description available 1 1 read-write 0 No current breakpoint debug event #0 1 At least one current breakpoint debug event #1 DWTTRAP no description available 2 1 read-write 0 No current debug events generated by the DWT #0 1 At least one current debug event generated by the DWT #1 EXTERNAL no description available 4 1 read-write 0 No EDBGRQ debug event #0 1 EDBGRQ debug event #1 HALTED no description available 0 1 read-write 0 No active halt request debug event #0 1 Halt request debug event active #1 VCATCH no description available 3 1 read-write 0 No Vector catch triggered #0 1 Vector catch triggered #1 SCB_FPCAR Floating-point Context Address Register 0xF38 32 read-write n 0x0 0x0 ADDRESS The location of the unpopulated floating-point register space allocated on an exception stack frame. 3 29 read-write SCB_FPCCR Floating-point Context Control Register 0xF34 32 read-write n 0x0 0x0 ASPEN Enables CONTROL2 setting on execution of a floating-point instruction. This results in automatic hardware state preservation and restoration, for floating-point context, on exception entry and exit. 31 1 read-write 0 Disable CONTROL2 setting on execution of a floating-point instruction. #0 1 Enable CONTROL2 setting on execution of a floating-point instruction. #1 BFRDY Permission to set the BusFault handler to the pending state when the floating-point stack frame was allocated. 6 1 read-write 0 BusFault is disabled or priority did not permit setting the BusFault handler to the pending state when the floating-point stack frame was allocated. #0 1 BusFault is disabled or priority did not permit setting the BusFault handler to the pending state when the floating-point stack frame was allocated. #1 HFRDY Permission to set the HardFault handler to the pending state when the floating-point stack frame was allocated. 4 1 read-write 0 Priority did not permit setting the HardFault handler to the pending state when the floating-point stack frame was allocated. #0 1 Priority permitted setting the HardFault handler to the pending state when the floating-point stack frame was allocated. #1 LSPACT Lazy state preservation. 0 1 read-write 0 Lazy state preservation is not active. #0 1 Lazy state preservation is active. floating-point stack frame has been allocated but saving state to it has been deferred. #1 LSPEN Lazy state preservation for floating-point context. 30 1 read-write 0 Disable automatic lazy state preservation for floating-point context. #0 1 Enable automatic lazy state preservation for floating-point context. #1 MMRDY Permission to set the MemManage handler to the pending state when the floating-point stack frame was allocated. 5 1 read-write 0 MemManage is disabled or priority did not permit setting the MemManage handler to the pending state when the floating-point stack frame was allocated. #0 1 MemManage is enabled and priority permitted setting the MemManage handler to the pending state when the floating-point stack frame was allocated. #1 MONRDY Permission to set the MON_PEND when the floating-point stack frame was allocated. 8 1 read-write 0 DebugMonitor is disabled or priority did not permit setting MON_PEND when the floating-point stack frame was allocated. #0 1 DebugMonitor is enabled and priority permits setting MON_PEND when the floating-point stack frame was allocated. #1 THREAD Mode when the floating-point stack frame was allocated. 3 1 read-write 0 Mode was not Thread Mode when the floating-point stack frame was allocated. #0 1 Mode was Thread Mode when the floating-point stack frame was allocated. #1 USER Privilege level when the floating-point stack frame was allocated. 1 1 read-write 0 Privilege level was not user when the floating-point stack frame was allocated. #0 1 Privilege level was user when the floating-point stack frame was allocated. #1 SCB_FPDSCR Floating-point Default Status Control Register 0xF3C 32 read-write n 0x0 0x0 AHP Default value for FPSCR.AHP (Alternative half-precision control bit). 26 1 read-write 0 IEEE half-precision format selected. #0 1 Alternative half-precision format selected. #1 DN Default value for FPSCR.DN (Default NaN mode control bit). 25 1 read-write 0 NaN operands propagate through to the output of a floating-point operation. #0 1 Any operation involving one or more NaNs returns the Default NaN. #1 FZ Default value for FPSCR.FZ (Flush-to-zero mode control bit). 24 1 read-write 0 Flush-to-zero mode disabled. Behavior of the floating-point system is fully compliant with the IEEE 754 standard. #0 1 Flush-to-zero mode enabled. #1 RMode Default value for FPSCR.RMode (Rounding Mode control field). 22 2 read-write 00 Round to Nearest (RN) mode #00 01 Round towards Plus Infinity (RP) mode. #01 10 Round towards Minus Infinity (RM) mode. #10 11 Round towards Zero (RZ) mode. #11 SCB_HFSR HardFault Status register 0xD2C 32 read-write n 0x0 0x0 DEBUGEVT no description available 31 1 read-write FORCED no description available 30 1 read-write 0 no forced HardFault #0 1 forced HardFault #1 VECTTBL no description available 1 1 read-write 0 no BusFault on vector table read #0 1 BusFault on vector table read #1 SCB_ICSR Interrupt Control and State Register 0xD04 32 read-write n 0x0 0x0 ISRPENDING no description available 22 1 read-only ISRPREEMPT no description available 23 1 read-only 0 Will not service #0 1 Will service a pending exception #1 NMIPENDSET no description available 31 1 read-write 0 write: no effect; read: NMI exception is not pending #0 1 write: changes NMI exception state to pending; read: NMI exception is pending #1 PENDSTCLR no description available 25 1 write-only 0 no effect #0 1 removes the pending state from the SysTick exception #1 PENDSTSET no description available 26 1 read-write 0 write: no effect; read: SysTick exception is not pending #0 1 write: changes SysTick exception state to pending; read: SysTick exception is pending #1 PENDSVCLR no description available 27 1 write-only 0 no effect #0 1 removes the pending state from the PendSV exception #1 PENDSVSET no description available 28 1 read-write 0 write: no effect; read: PendSV exception is not pending #0 1 write: changes PendSV exception state to pending; read: PendSV exception is pending #1 RETTOBASE no description available 11 1 read-only 0 there are preempted active exceptions to execute #0 1 there are no active exceptions, or the currently-executing exception is the only active exception #1 VECTACTIVE Active exception number 0 9 read-only VECTPENDING Exception number of the highest priority pending enabled exception 12 6 read-only SCB_MMFAR MemManage Address Register 0xD34 32 read-write n 0x0 0x0 ADDRESS Address of MemManage fault location 0 32 read-write SCB_SCR System Control Register 0xD10 32 read-write n 0x0 0x0 SEVONPEND no description available 4 1 read-write 0 only enabled interrupts or events can wakeup the processor, disabled interrupts are excluded #0 1 enabled events and all interrupts, including disabled interrupts, can wakeup the processor #1 SLEEPDEEP no description available 2 1 read-write 0 sleep #0 1 deep sleep #1 SLEEPONEXIT no description available 1 1 read-write 0 o not sleep when returning to Thread mode #0 1 enter sleep, or deep sleep, on return from an ISR #1 SCB_SHCSR System Handler Control and State Register 0xD24 32 read-write n 0x0 0x0 BUSFAULTACT no description available 1 1 read-write 0 exception is not active #0 1 exception is active #1 BUSFAULTENA no description available 17 1 read-write 0 disable the exception #0 1 enable the exception #1 BUSFAULTPENDED no description available 14 1 read-write 0 exception is not pending #0 1 exception is pending #1 MEMFAULTACT no description available 0 1 read-write 0 exception is not active #0 1 exception is active #1 MEMFAULTENA no description available 16 1 read-write 0 disable the exception #0 1 enable the exception #1 MEMFAULTPENDED no description available 13 1 read-write 0 exception is not pending #0 1 exception is pending #1 MONITORACT no description available 8 1 read-write 0 exception is not active #0 1 exception is active #1 PENDSVACT no description available 10 1 read-write 0 exception is not active #0 1 exception is active #1 SVCALLACT no description available 7 1 read-write 0 exception is not active #0 1 exception is active #1 SVCALLPENDED no description available 15 1 read-write 0 exception is not pending #0 1 exception is pending #1 SYSTICKACT no description available 11 1 read-write 0 exception is not active #0 1 exception is active #1 USGFAULTACT no description available 3 1 read-write 0 exception is not active #0 1 exception is active #1 USGFAULTENA no description available 18 1 read-write 0 disable the exception #0 1 enable the exception #1 USGFAULTPENDED no description available 12 1 read-write 0 exception is not pending #0 1 exception is pending #1 SCB_SHPR1 System Handler Priority Register 1 0xD18 32 read-write n 0x0 0x0 PRI_4 Priority of system handler 4, MemManage 0 8 read-write PRI_5 Priority of system handler 5, BusFault 8 8 read-write PRI_6 Priority of system handler 6, UsageFault 16 8 read-write SCB_SHPR2 System Handler Priority Register 2 0xD1C 32 read-write n 0x0 0x0 PRI_11 Priority of system handler 11, SVCall 24 8 read-write SCB_SHPR3 System Handler Priority Register 3 0xD20 32 read-write n 0x0 0x0 PRI_14 Priority of system handler 14, PendSV 16 8 read-write PRI_15 Priority of system handler 15, SysTick exception 24 8 read-write SCB_VTOR Vector Table Offset Register 0xD08 32 read-write n 0x0 0x0 TBLOFF Vector table base offset 7 25 read-write SysTick System timer SysTick 0x0 0x0 0x10 registers n SYST_CALIB SysTick Calibration Value Register 0xC 32 read-only n 0x0 0x0 NOREF no description available 31 1 read-only 0 The reference clock is provided #0 1 The reference clock is not provided #1 SKEW no description available 30 1 read-only 0 10ms calibration value is exact #0 1 10ms calibration value is inexact, because of the clock frequency #1 TENMS Reload value to use for 10ms timing 0 24 read-only SYST_CSR SysTick Control and Status Register 0x0 32 read-write n 0x0 0x0 CLKSOURCE no description available 2 1 read-write 0 external clock #0 1 processor clock #1 COUNTFLAG no description available 16 1 read-write ENABLE no description available 0 1 read-write 0 counter disabled #0 1 counter enabled #1 TICKINT no description available 1 1 read-write 0 counting down to 0 does not assert the SysTick exception request #0 1 counting down to 0 asserts the SysTick exception request #1 SYST_CVR SysTick Current Value Register 0x8 32 read-write n 0x0 0x0 CURRENT Current value at the time the register is accessed 0 24 read-write SYST_RVR SysTick Reload Value Register 0x4 32 read-write n 0x0 0x0 RELOAD Value to load into the SysTick Current Value Register when the counter reaches 0 0 24 read-write UART0 Serial Communication Interface UART 0x0 0x0 0x40 registers n UART0_RX_TX 31 UART0_ERR 32 AP7816A_T0 UART 7816 ATR Duration Timer Register A 0x3A 8 read-write n 0x0 0x0 ADTI_H ATR Duration Time Integer High (C7816[TTYPE] = 0) 0 8 read-write AP7816B_T0 UART 7816 ATR Duration Timer Register B 0x3B 8 read-write n 0x0 0x0 ADTI_L ATR Duration Time Integer Low (C7816[TTYPE] = 0) 0 8 read-write BDH UART Baud Rate Registers: High 0x0 8 read-write n 0x0 0x0 LBKDIE LIN Break Detect Interrupt Enable 7 1 read-write 0 LBKDIF interrupt requests disabled. #0 1 LBKDIF interrupt requests enabled. #1 RXEDGIE RxD Input Active Edge Interrupt Enable 6 1 read-write 0 Hardware interrupts from RXEDGIF disabled using polling. #0 1 RXEDGIF interrupt request enabled. #1 SBR UART Baud Rate Bits 0 5 read-write BDL UART Baud Rate Registers: Low 0x1 8 read-write n 0x0 0x0 SBR UART Baud Rate Bits 0 8 read-write C1 UART Control Register 1 0x2 8 read-write n 0x0 0x0 ILT Idle Line Type Select 2 1 read-write 0 Idle character bit count starts after start bit. #0 1 Idle character bit count starts after stop bit. #1 LOOPS Loop Mode Select 7 1 read-write 0 Normal operation. #0 1 Loop mode where transmitter output is internally connected to receiver input. The receiver input is determined by RSRC. #1 M 9-bit or 8-bit Mode Select 4 1 read-write 0 Normal-start + 8 data bits (MSB/LSB first as determined by MSBF) + stop. #0 1 Use-start + 9 data bits (MSB/LSB first as determined by MSBF) + stop. #1 PE Parity Enable 1 1 read-write 0 Parity function disabled. #0 1 Parity function enabled. #1 PT Parity Type 0 1 read-write 0 Even parity. #0 1 Odd parity. #1 RSRC Receiver Source Select 5 1 read-write 0 Selects internal loop back mode. The receiver input is internally connected to transmitter output. #0 1 Single wire UART mode where the receiver input is connected to the transmit pin input signal. #1 UARTSWAI UART Stops in Wait Mode 6 1 read-write 0 UART clock continues to run in Wait mode. #0 1 UART clock freezes while CPU is in Wait mode. #1 WAKE Receiver Wakeup Method Select 3 1 read-write 0 Idle line wakeup. #0 1 Address mark wakeup. #1 C2 UART Control Register 2 0x3 8 read-write n 0x0 0x0 ILIE Idle Line Interrupt Enable 4 1 read-write 0 IDLE interrupt requests disabled. #0 1 IDLE interrupt requests enabled. #1 RE Receiver Enable 2 1 read-write 0 Receiver off. #0 1 Receiver on. #1 RIE Receiver Full Interrupt or DMA Transfer Enable 5 1 read-write 0 RDRF interrupt and DMA transfer requests disabled. #0 1 RDRF interrupt or DMA transfer requests enabled. #1 RWU Receiver Wakeup Control 1 1 read-write 0 Normal operation. #0 1 RWU enables the wakeup function and inhibits further receiver interrupt requests. Normally, hardware wakes the receiver by automatically clearing RWU. #1 SBK Send Break 0 1 read-write 0 Normal transmitter operation. #0 1 Queue break characters to be sent. #1 TCIE Transmission Complete Interrupt Enable 6 1 read-write 0 TC interrupt requests disabled. #0 1 TC interrupt requests enabled. #1 TE Transmitter Enable 3 1 read-write 0 Transmitter off. #0 1 Transmitter on. #1 TIE Transmitter Interrupt or DMA Transfer Enable. 7 1 read-write 0 TDRE interrupt and DMA transfer requests disabled. #0 1 TDRE interrupt or DMA transfer requests enabled. #1 C3 UART Control Register 3 0x6 8 read-write n 0x0 0x0 FEIE Framing Error Interrupt Enable 1 1 read-write 0 FE interrupt requests are disabled. #0 1 FE interrupt requests are enabled. #1 NEIE Noise Error Interrupt Enable 2 1 read-write 0 NF interrupt requests are disabled. #0 1 NF interrupt requests are enabled. #1 ORIE Overrun Error Interrupt Enable 3 1 read-write 0 OR interrupts are disabled. #0 1 OR interrupt requests are enabled. #1 PEIE Parity Error Interrupt Enable 0 1 read-write 0 PF interrupt requests are disabled. #0 1 PF interrupt requests are enabled. #1 R8 Received Bit 8 7 1 read-only T8 Transmit Bit 8 6 1 read-write TXDIR Transmitter Pin Data Direction in Single-Wire mode 5 1 read-write 0 TXD pin is an input in single wire mode. #0 1 TXD pin is an output in single wire mode. #1 TXINV Transmit Data Inversion. 4 1 read-write 0 Transmit data is not inverted. #0 1 Transmit data is inverted. #1 C4 UART Control Register 4 0xA 8 read-write n 0x0 0x0 BRFA Baud Rate Fine Adjust 0 5 read-write M10 10-bit Mode select 5 1 read-write 0 The parity bit is the ninth bit in the serial transmission. #0 1 The parity bit is the tenth bit in the serial transmission. #1 MAEN1 Match Address Mode Enable 1 7 1 read-write 0 All data received is transferred to the data buffer if MAEN2 is cleared. #0 1 All data received with the most significant bit cleared, is discarded. All data received with the most significant bit set, is compared with contents of MA1 register. If no match occurs, the data is discarded. If match occurs, data is transferred to the data buffer. This field must be cleared when C7816[ISO7816E] is set/enabled. #1 MAEN2 Match Address Mode Enable 2 6 1 read-write 0 All data received is transferred to the data buffer if MAEN1 is cleared. #0 1 All data received with the most significant bit cleared, is discarded. All data received with the most significant bit set, is compared with contents of MA2 register. If no match occurs, the data is discarded. If a match occurs, data is transferred to the data buffer. This field must be cleared when C7816[ISO7816E] is set/enabled. #1 C5 UART Control Register 5 0xB 8 read-write n 0x0 0x0 RDMAS Receiver Full DMA Select 5 1 read-write 0 If C2[RIE] and S1[RDRF] are set, the RDFR interrupt request signal is asserted to request an interrupt service. #0 1 If C2[RIE] and S1[RDRF] are set, the RDRF DMA request signal is asserted to request a DMA transfer. #1 TDMAS Transmitter DMA Select 7 1 read-write 0 If C2[TIE] is set and the S1[TDRE] flag is set, the TDRE interrupt request signal is asserted to request interrupt service. #0 1 If C2[TIE] is set and the S1[TDRE] flag is set, the TDRE DMA request signal is asserted to request a DMA transfer. #1 C7816 UART 7816 Control Register 0x18 8 read-write n 0x0 0x0 ANACK Generate NACK on Error 3 1 read-write 0 No NACK is automatically generated. #0 1 A NACK is automatically generated if a parity error is detected or if an invalid initial character is detected. #1 INIT Detect Initial Character 2 1 read-write 0 Normal operating mode. Receiver does not seek to identify initial character. #0 1 Receiver searches for initial character. #1 ISO_7816E ISO-7816 Functionality Enabled 0 1 read-write 0 ISO-7816 functionality is turned off/not enabled. #0 1 ISO-7816 functionality is turned on/enabled. #1 ONACK Generate NACK on Overflow 4 1 read-write 0 The received data does not generate a NACK when the receipt of the data results in an overflow event. #0 1 If the receiver buffer overflows, a NACK is automatically sent on a received character. #1 TTYPE Transfer Type 1 1 read-write 0 T = 0 per the ISO-7816 specification. #0 1 T = 1 per the ISO-7816 specification. #1 CFIFO UART FIFO Control Register 0x11 8 read-write n 0x0 0x0 RXFLUSH Receive FIFO/Buffer Flush 6 1 write-only 0 No flush operation occurs. #0 1 All data in the receive FIFO/buffer is cleared out. #1 RXOFE Receive FIFO Overflow Interrupt Enable 2 1 read-write 0 RXOF flag does not generate an interrupt to the host. #0 1 RXOF flag generates an interrupt to the host. #1 RXUFE Receive FIFO Underflow Interrupt Enable 0 1 read-write 0 RXUF flag does not generate an interrupt to the host. #0 1 RXUF flag generates an interrupt to the host. #1 TXFLUSH Transmit FIFO/Buffer Flush 7 1 write-only 0 No flush operation occurs. #0 1 All data in the transmit FIFO/Buffer is cleared out. #1 TXOFE Transmit FIFO Overflow Interrupt Enable 1 1 read-write 0 TXOF flag does not generate an interrupt to the host. #0 1 TXOF flag generates an interrupt to the host. #1 D UART Data Register 0x7 8 read-write n 0x0 0x0 RT Reads return the contents of the read-only receive data register and writes go to the write-only transmit data register 0 8 read-write ED UART Extended Data Register 0xC 8 read-only n 0x0 0x0 NOISY The current received dataword contained in D and C3[R8] was received with noise. 7 1 read-only 0 The dataword was received without noise. #0 1 The data was received with noise. #1 PARITYE The current received dataword contained in D and C3[R8] was received with a parity error. 6 1 read-only 0 The dataword was received without a parity error. #0 1 The dataword was received with a parity error. #1 ET7816 UART 7816 Error Threshold Register 0x1E 8 read-write n 0x0 0x0 RXTHRESHOLD Receive NACK Threshold 0 4 read-write TXTHRESHOLD Transmit NACK Threshold 4 4 read-write 0 TXT asserts on the first NACK that is received. #0000 1 TXT asserts on the second NACK that is received. #0001 IE7816 UART 7816 Interrupt Enable Register 0x19 8 read-write n 0x0 0x0 ADTE ATR Duration Timer Interrupt Enable 3 1 read-write 0 The assertion of IS7816[ADT] does not result in the generation of an interrupt. #0 1 The assertion of IS7816[ADT] results in the generation of an interrupt. #1 BWTE Block Wait Timer Interrupt Enable 5 1 read-write 0 The assertion of IS7816[BWT] does not result in the generation of an interrupt. #0 1 The assertion of IS7816[BWT] results in the generation of an interrupt. #1 CWTE Character Wait Timer Interrupt Enable 6 1 read-write 0 The assertion of IS7816[CWT] does not result in the generation of an interrupt. #0 1 The assertion of IS7816[CWT] results in the generation of an interrupt. #1 GTVE Guard Timer Violated Interrupt Enable 2 1 read-write 0 The assertion of IS7816[GTV] does not result in the generation of an interrupt. #0 1 The assertion of IS7816[GTV] results in the generation of an interrupt. #1 INITDE Initial Character Detected Interrupt Enable 4 1 read-write 0 The assertion of IS7816[INITD] does not result in the generation of an interrupt. #0 1 The assertion of IS7816[INITD] results in the generation of an interrupt. #1 RXTE Receive Threshold Exceeded Interrupt Enable 0 1 read-write 0 The assertion of IS7816[RXT] does not result in the generation of an interrupt. #0 1 The assertion of IS7816[RXT] results in the generation of an interrupt. #1 TXTE Transmit Threshold Exceeded Interrupt Enable 1 1 read-write 0 The assertion of IS7816[TXT] does not result in the generation of an interrupt. #0 1 The assertion of IS7816[TXT] results in the generation of an interrupt. #1 WTE Wait Timer Interrupt Enable 7 1 read-write 0 The assertion of IS7816[WT] does not result in the generation of an interrupt. #0 1 The assertion of IS7816[WT] results in the generation of an interrupt. #1 IR UART Infrared Register 0xE 8 read-write n 0x0 0x0 IREN Infrared enable 2 1 read-write 0 IR disabled. #0 1 IR enabled. #1 TNP Transmitter narrow pulse 0 2 read-write 00 3/16. #00 01 1/16. #01 10 1/32. #10 11 1/4. #11 IS7816 UART 7816 Interrupt Status Register 0x1A 8 read-write n 0x0 0x0 ADT ATR Duration Time Interrupt 3 1 read-write 0 ATR Duration time (ADT) has not been violated. #0 1 ATR Duration time (ADT) has been violated. #1 BWT Block Wait Timer Interrupt 5 1 read-write 0 Block wait time (BWT) has not been violated. #0 1 Block wait time (BWT) has been violated. #1 CWT Character Wait Timer Interrupt 6 1 read-write 0 Character wait time (CWT) has not been violated. #0 1 Character wait time (CWT) has been violated. #1 GTV Guard Timer Violated Interrupt 2 1 read-write 0 A guard time (GT, CGT, or BGT) has not been violated. #0 1 A guard time (GT, CGT, or BGT) has been violated. #1 INITD Initial Character Detected Interrupt 4 1 read-write 0 A valid initial character has not been received. #0 1 A valid initial character has been received. #1 RXT Receive Threshold Exceeded Interrupt 0 1 read-write 0 The number of consecutive NACKS generated as a result of parity errors and buffer overruns is less than or equal to the value in ET7816[RXTHRESHOLD]. #0 1 The number of consecutive NACKS generated as a result of parity errors and buffer overruns is greater than the value in ET7816[RXTHRESHOLD]. #1 TXT Transmit Threshold Exceeded Interrupt 1 1 read-write 0 The number of retries and corresponding NACKS does not exceed the value in ET7816[TXTHRESHOLD]. #0 1 The number of retries and corresponding NACKS exceeds the value in ET7816[TXTHRESHOLD]. #1 WT Wait Timer Interrupt 7 1 read-write 0 Wait time (WT) has not been violated. #0 1 Wait time (WT) has been violated. #1 MA1 UART Match Address Registers 1 0x8 8 read-write n 0x0 0x0 MA Match Address 0 8 read-write MA2 UART Match Address Registers 2 0x9 8 read-write n 0x0 0x0 MA Match Address 0 8 read-write MODEM UART Modem Register 0xD 8 read-write n 0x0 0x0 RXRTSE Receiver request-to-send enable 3 1 read-write 0 The receiver has no effect on RTS. #0 1 RTS is deasserted if the number of characters in the receiver data register (FIFO) is equal to or greater than RWFIFO[RXWATER]. RTS is asserted when the number of characters in the receiver data register (FIFO) is less than RWFIFO[RXWATER]. #1 TXCTSE Transmitter clear-to-send enable 0 1 read-write 0 CTS has no effect on the transmitter. #0 1 Enables clear-to-send operation. The transmitter checks the state of CTS each time it is ready to send a character. If CTS is asserted, the character is sent. If CTS is deasserted, the signal TXD remains in the mark state and transmission is delayed until CTS is asserted. Changes in CTS as a character is being sent do not affect its transmission. #1 TXRTSE Transmitter request-to-send enable 1 1 read-write 0 The transmitter has no effect on RTS. #0 1 When a character is placed into an empty transmitter data buffer , RTS asserts one bit time before the start bit is transmitted. RTS deasserts one bit time after all characters in the transmitter data buffer and shift register are completely sent, including the last stop bit. (FIFO) (FIFO) #1 TXRTSPOL Transmitter request-to-send polarity 2 1 read-write 0 Transmitter RTS is active low. #0 1 Transmitter RTS is active high. #1 PFIFO UART FIFO Parameters 0x10 8 read-write n 0x0 0x0 RXFE Receive FIFO Enable 3 1 read-write 0 Receive FIFO is not enabled. Buffer is depth 1. (Legacy support) #0 1 Receive FIFO is enabled. Buffer is depth indicted by RXFIFOSIZE. #1 RXFIFOSIZE Receive FIFO. Buffer Depth 0 3 read-only 000 Receive FIFO/Buffer depth = 1 dataword. #000 001 Receive FIFO/Buffer depth = 4 datawords. #001 010 Receive FIFO/Buffer depth = 8 datawords. #010 011 Receive FIFO/Buffer depth = 16 datawords. #011 100 Receive FIFO/Buffer depth = 32 datawords. #100 101 Receive FIFO/Buffer depth = 64 datawords. #101 110 Receive FIFO/Buffer depth = 128 datawords. #110 TXFE Transmit FIFO Enable 7 1 read-write 0 Transmit FIFO is not enabled. Buffer is depth 1. (Legacy support). #0 1 Transmit FIFO is enabled. Buffer is depth indicated by TXFIFOSIZE. #1 TXFIFOSIZE Transmit FIFO. Buffer Depth 4 3 read-only 000 Transmit FIFO/Buffer depth = 1 dataword. #000 001 Transmit FIFO/Buffer depth = 4 datawords. #001 010 Transmit FIFO/Buffer depth = 8 datawords. #010 011 Transmit FIFO/Buffer depth = 16 datawords. #011 100 Transmit FIFO/Buffer depth = 32 datawords. #100 101 Transmit FIFO/Buffer depth = 64 datawords. #101 110 Transmit FIFO/Buffer depth = 128 datawords. #110 RCFIFO UART FIFO Receive Count 0x16 8 read-only n 0x0 0x0 RXCOUNT Receive Counter 0 8 read-only RWFIFO UART FIFO Receive Watermark 0x15 8 read-write n 0x0 0x0 RXWATER Receive Watermark 0 8 read-write S1 UART Status Register 1 0x4 8 read-only n 0x0 0x0 FE Framing Error Flag 1 1 read-only 0 No framing error detected. #0 1 Framing error. #1 IDLE Idle Line Flag 4 1 read-only 0 Receiver input is either active now or has never become active since the IDLE flag was last cleared. #0 1 Receiver input has become idle or the flag has not been cleared since it last asserted. #1 NF Noise Flag 2 1 read-only 0 No noise detected since the last time this flag was cleared. If the receive buffer has a depth greater than 1 then there may be data in the receiver buffer that was received with noise. #0 1 At least one dataword was received with noise detected since the last time the flag was cleared. #1 OR Receiver Overrun Flag 3 1 read-only 0 No overrun has occurred since the last time the flag was cleared. #0 1 Overrun has occurred or the overrun flag has not been cleared since the last overrun occurred. #1 PF Parity Error Flag 0 1 read-only 0 No parity error detected since the last time this flag was cleared. If the receive buffer has a depth greater than 1, then there may be data in the receive buffer what was received with a parity error. #0 1 At least one dataword was received with a parity error since the last time this flag was cleared. #1 RDRF Receive Data Register Full Flag 5 1 read-only 0 The number of datawords in the receive buffer is less than the number indicated by RXWATER. #0 1 The number of datawords in the receive buffer is equal to or greater than the number indicated by RXWATER at some point in time since this flag was last cleared. #1 TC Transmit Complete Flag 6 1 read-only 0 Transmitter active (sending data, a preamble, or a break). #0 1 Transmitter idle (transmission activity complete). #1 TDRE Transmit Data Register Empty Flag 7 1 read-only 0 The amount of data in the transmit buffer is greater than the value indicated by TWFIFO[TXWATER]. #0 1 The amount of data in the transmit buffer is less than or equal to the value indicated by TWFIFO[TXWATER] at some point in time since the flag has been cleared. #1 S2 UART Status Register 2 0x5 8 read-write n 0x0 0x0 BRK13 Break Transmit Character Length 2 1 read-write 0 Break character is 10, 11, or 12 bits long. #0 1 Break character is 13 or 14 bits long. #1 LBKDE LIN Break Detection Enable 1 1 read-write 0 Break character detection is disabled. #0 1 Break character is detected at length of 11 bit times if C1[M] = 0 or 12 bits time if C1[M] = 1. #1 LBKDIF LIN Break Detect Interrupt Flag 7 1 read-write 0 No LIN break character detected. #0 1 LIN break character detected. #1 MSBF Most Significant Bit First 5 1 read-write 0 LSB (bit0) is the first bit that is transmitted following the start bit. Further, the first bit received after the start bit is identified as bit0. #0 1 MSB (bit8, bit7 or bit6) is the first bit that is transmitted following the start bit, depending on the setting of C1[M] and C1[PE]. Further, the first bit received after the start bit is identified as bit8, bit7, or bit6, depending on the setting of C1[M] and C1[PE]. #1 RAF Receiver Active Flag 0 1 read-only 0 UART receiver idle/inactive waiting for a start bit. #0 1 UART receiver active, RxD input not idle. #1 RWUID Receive Wakeup Idle Detect 3 1 read-write 0 S1[IDLE] is not set upon detection of an idle character. #0 1 S1[IDLE] is set upon detection of an idle character. #1 RXEDGIF RxD Pin Active Edge Interrupt Flag 6 1 read-write 0 No active edge on the receive pin has occurred. #0 1 An active edge on the receive pin has occurred. #1 RXINV Receive Data Inversion 4 1 read-write 0 Receive data is not inverted. #0 1 Receive data is inverted. #1 SFIFO UART FIFO Status Register 0x12 8 read-write n 0x0 0x0 RXEMPT Receive Buffer/FIFO Empty 6 1 read-only 0 Receive buffer is not empty. #0 1 Receive buffer is empty. #1 RXOF Receiver Buffer Overflow Flag 2 1 read-write 0 No receive buffer overflow has occurred since the last time the flag was cleared. #0 1 At least one receive buffer overflow has occurred since the last time the flag was cleared. #1 RXUF Receiver Buffer Underflow Flag 0 1 read-write 0 No receive buffer underflow has occurred since the last time the flag was cleared. #0 1 At least one receive buffer underflow has occurred since the last time the flag was cleared. #1 TXEMPT Transmit Buffer/FIFO Empty 7 1 read-only 0 Transmit buffer is not empty. #0 1 Transmit buffer is empty. #1 TXOF Transmitter Buffer Overflow Flag 1 1 read-write 0 No transmit buffer overflow has occurred since the last time the flag was cleared. #0 1 At least one transmit buffer overflow has occurred since the last time the flag was cleared. #1 TCFIFO UART FIFO Transmit Count 0x14 8 read-only n 0x0 0x0 TXCOUNT Transmit Counter 0 8 read-only TL7816 UART 7816 Transmit Length Register 0x1F 8 read-write n 0x0 0x0 TLEN Transmit Length 0 8 read-write TWFIFO UART FIFO Transmit Watermark 0x13 8 read-write n 0x0 0x0 TXWATER Transmit Watermark 0 8 read-write WF7816 UART 7816 Wait FD Register 0x1D 8 read-write n 0x0 0x0 GTFD FD Multiplier 0 8 read-write WGP7816_T1 UART 7816 Wait and Guard Parameter Register 0x3E 8 read-write n 0x0 0x0 BGI Block Guard Time Integer (C7816[TTYPE] = 1) 0 4 read-write CWI1 Character Wait Time Integer 1 (C7816[TTYPE] = 1) 4 4 read-write WN7816 UART 7816 Wait N Register 0x1C 8 read-write n 0x0 0x0 GTN Guard Band N 0 8 read-write WP7816 UART 7816 Wait Parameter Register 0x1B 8 read-write n 0x0 0x0 WTX Wait Time Multiplier (C7816[TTYPE] = 1) 0 8 read-write WP7816A_T0 UART 7816 Wait Parameter Register A UART0 0x3C 8 read-write n 0x0 0x0 WI_H Wait Time Integer High (C7816[TTYPE] = 0) 0 8 read-write WP7816A_T1 UART 7816 Wait Parameter Register A UART0 0x3C 8 read-write n 0x0 0x0 BWI_H Block Wait Time Integer High (C7816[TTYPE] = 1) 0 8 read-write WP7816B_T0 UART 7816 Wait Parameter Register B UART0 0x3D 8 read-write n 0x0 0x0 WI_L Wait Time Integer Low (C7816[TTYPE] = 0) 0 8 read-write WP7816B_T1 UART 7816 Wait Parameter Register B UART0 0x3D 8 read-write n 0x0 0x0 BWI_L Block Wait Time Integer Low (C7816[TTYPE] = 1) 0 8 read-write WP7816C_T1 UART 7816 Wait Parameter Register C 0x3F 8 read-write n 0x0 0x0 CWI2 Character Wait Time Integer 2 (C7816[TTYPE] = 1) 0 5 read-write UART1 Serial Communication Interface UART 0x0 0x0 0x17 registers n UART1_RX_TX 33 UART1_ERR 34 BDH UART Baud Rate Registers: High 0x0 8 read-write n 0x0 0x0 LBKDIE LIN Break Detect Interrupt Enable 7 1 read-write 0 LBKDIF interrupt requests disabled. #0 1 LBKDIF interrupt requests enabled. #1 RXEDGIE RxD Input Active Edge Interrupt Enable 6 1 read-write 0 Hardware interrupts from RXEDGIF disabled using polling. #0 1 RXEDGIF interrupt request enabled. #1 SBR UART Baud Rate Bits 0 5 read-write BDL UART Baud Rate Registers: Low 0x1 8 read-write n 0x0 0x0 SBR UART Baud Rate Bits 0 8 read-write C1 UART Control Register 1 0x2 8 read-write n 0x0 0x0 ILT Idle Line Type Select 2 1 read-write 0 Idle character bit count starts after start bit. #0 1 Idle character bit count starts after stop bit. #1 LOOPS Loop Mode Select 7 1 read-write 0 Normal operation. #0 1 Loop mode where transmitter output is internally connected to receiver input. The receiver input is determined by RSRC. #1 M 9-bit or 8-bit Mode Select 4 1 read-write 0 Normal-start + 8 data bits (MSB/LSB first as determined by MSBF) + stop. #0 1 Use-start + 9 data bits (MSB/LSB first as determined by MSBF) + stop. #1 PE Parity Enable 1 1 read-write 0 Parity function disabled. #0 1 Parity function enabled. #1 PT Parity Type 0 1 read-write 0 Even parity. #0 1 Odd parity. #1 RSRC Receiver Source Select 5 1 read-write 0 Selects internal loop back mode. The receiver input is internally connected to transmitter output. #0 1 Single wire UART mode where the receiver input is connected to the transmit pin input signal. #1 UARTSWAI UART Stops in Wait Mode 6 1 read-write 0 UART clock continues to run in Wait mode. #0 1 UART clock freezes while CPU is in Wait mode. #1 WAKE Receiver Wakeup Method Select 3 1 read-write 0 Idle line wakeup. #0 1 Address mark wakeup. #1 C2 UART Control Register 2 0x3 8 read-write n 0x0 0x0 ILIE Idle Line Interrupt Enable 4 1 read-write 0 IDLE interrupt requests disabled. #0 1 IDLE interrupt requests enabled. #1 RE Receiver Enable 2 1 read-write 0 Receiver off. #0 1 Receiver on. #1 RIE Receiver Full Interrupt or DMA Transfer Enable 5 1 read-write 0 RDRF interrupt and DMA transfer requests disabled. #0 1 RDRF interrupt or DMA transfer requests enabled. #1 RWU Receiver Wakeup Control 1 1 read-write 0 Normal operation. #0 1 RWU enables the wakeup function and inhibits further receiver interrupt requests. Normally, hardware wakes the receiver by automatically clearing RWU. #1 SBK Send Break 0 1 read-write 0 Normal transmitter operation. #0 1 Queue break characters to be sent. #1 TCIE Transmission Complete Interrupt Enable 6 1 read-write 0 TC interrupt requests disabled. #0 1 TC interrupt requests enabled. #1 TE Transmitter Enable 3 1 read-write 0 Transmitter off. #0 1 Transmitter on. #1 TIE Transmitter Interrupt or DMA Transfer Enable. 7 1 read-write 0 TDRE interrupt and DMA transfer requests disabled. #0 1 TDRE interrupt or DMA transfer requests enabled. #1 C3 UART Control Register 3 0x6 8 read-write n 0x0 0x0 FEIE Framing Error Interrupt Enable 1 1 read-write 0 FE interrupt requests are disabled. #0 1 FE interrupt requests are enabled. #1 NEIE Noise Error Interrupt Enable 2 1 read-write 0 NF interrupt requests are disabled. #0 1 NF interrupt requests are enabled. #1 ORIE Overrun Error Interrupt Enable 3 1 read-write 0 OR interrupts are disabled. #0 1 OR interrupt requests are enabled. #1 PEIE Parity Error Interrupt Enable 0 1 read-write 0 PF interrupt requests are disabled. #0 1 PF interrupt requests are enabled. #1 R8 Received Bit 8 7 1 read-only T8 Transmit Bit 8 6 1 read-write TXDIR Transmitter Pin Data Direction in Single-Wire mode 5 1 read-write 0 TXD pin is an input in single wire mode. #0 1 TXD pin is an output in single wire mode. #1 TXINV Transmit Data Inversion. 4 1 read-write 0 Transmit data is not inverted. #0 1 Transmit data is inverted. #1 C4 UART Control Register 4 0xA 8 read-write n 0x0 0x0 BRFA Baud Rate Fine Adjust 0 5 read-write M10 10-bit Mode select 5 1 read-write 0 The parity bit is the ninth bit in the serial transmission. #0 1 The parity bit is the tenth bit in the serial transmission. #1 MAEN1 Match Address Mode Enable 1 7 1 read-write 0 All data received is transferred to the data buffer if MAEN2 is cleared. #0 1 All data received with the most significant bit cleared, is discarded. All data received with the most significant bit set, is compared with contents of MA1 register. If no match occurs, the data is discarded. If match occurs, data is transferred to the data buffer. This field must be cleared when C7816[ISO7816E] is set/enabled. #1 MAEN2 Match Address Mode Enable 2 6 1 read-write 0 All data received is transferred to the data buffer if MAEN1 is cleared. #0 1 All data received with the most significant bit cleared, is discarded. All data received with the most significant bit set, is compared with contents of MA2 register. If no match occurs, the data is discarded. If a match occurs, data is transferred to the data buffer. This field must be cleared when C7816[ISO7816E] is set/enabled. #1 C5 UART Control Register 5 0xB 8 read-write n 0x0 0x0 RDMAS Receiver Full DMA Select 5 1 read-write 0 If C2[RIE] and S1[RDRF] are set, the RDFR interrupt request signal is asserted to request an interrupt service. #0 1 If C2[RIE] and S1[RDRF] are set, the RDRF DMA request signal is asserted to request a DMA transfer. #1 TDMAS Transmitter DMA Select 7 1 read-write 0 If C2[TIE] is set and the S1[TDRE] flag is set, the TDRE interrupt request signal is asserted to request interrupt service. #0 1 If C2[TIE] is set and the S1[TDRE] flag is set, the TDRE DMA request signal is asserted to request a DMA transfer. #1 CFIFO UART FIFO Control Register 0x11 8 read-write n 0x0 0x0 RXFLUSH Receive FIFO/Buffer Flush 6 1 write-only 0 No flush operation occurs. #0 1 All data in the receive FIFO/buffer is cleared out. #1 RXOFE Receive FIFO Overflow Interrupt Enable 2 1 read-write 0 RXOF flag does not generate an interrupt to the host. #0 1 RXOF flag generates an interrupt to the host. #1 RXUFE Receive FIFO Underflow Interrupt Enable 0 1 read-write 0 RXUF flag does not generate an interrupt to the host. #0 1 RXUF flag generates an interrupt to the host. #1 TXFLUSH Transmit FIFO/Buffer Flush 7 1 write-only 0 No flush operation occurs. #0 1 All data in the transmit FIFO/Buffer is cleared out. #1 TXOFE Transmit FIFO Overflow Interrupt Enable 1 1 read-write 0 TXOF flag does not generate an interrupt to the host. #0 1 TXOF flag generates an interrupt to the host. #1 D UART Data Register 0x7 8 read-write n 0x0 0x0 RT Reads return the contents of the read-only receive data register and writes go to the write-only transmit data register 0 8 read-write ED UART Extended Data Register 0xC 8 read-only n 0x0 0x0 NOISY The current received dataword contained in D and C3[R8] was received with noise. 7 1 read-only 0 The dataword was received without noise. #0 1 The data was received with noise. #1 PARITYE The current received dataword contained in D and C3[R8] was received with a parity error. 6 1 read-only 0 The dataword was received without a parity error. #0 1 The dataword was received with a parity error. #1 IR UART Infrared Register 0xE 8 read-write n 0x0 0x0 IREN Infrared enable 2 1 read-write 0 IR disabled. #0 1 IR enabled. #1 TNP Transmitter narrow pulse 0 2 read-write 00 3/16. #00 01 1/16. #01 10 1/32. #10 11 1/4. #11 MA1 UART Match Address Registers 1 0x8 8 read-write n 0x0 0x0 MA Match Address 0 8 read-write MA2 UART Match Address Registers 2 0x9 8 read-write n 0x0 0x0 MA Match Address 0 8 read-write MODEM UART Modem Register 0xD 8 read-write n 0x0 0x0 RXRTSE Receiver request-to-send enable 3 1 read-write 0 The receiver has no effect on RTS. #0 1 RTS is deasserted if the number of characters in the receiver data register (FIFO) is equal to or greater than RWFIFO[RXWATER]. RTS is asserted when the number of characters in the receiver data register (FIFO) is less than RWFIFO[RXWATER]. #1 TXCTSE Transmitter clear-to-send enable 0 1 read-write 0 CTS has no effect on the transmitter. #0 1 Enables clear-to-send operation. The transmitter checks the state of CTS each time it is ready to send a character. If CTS is asserted, the character is sent. If CTS is deasserted, the signal TXD remains in the mark state and transmission is delayed until CTS is asserted. Changes in CTS as a character is being sent do not affect its transmission. #1 TXRTSE Transmitter request-to-send enable 1 1 read-write 0 The transmitter has no effect on RTS. #0 1 When a character is placed into an empty transmitter data buffer , RTS asserts one bit time before the start bit is transmitted. RTS deasserts one bit time after all characters in the transmitter data buffer and shift register are completely sent, including the last stop bit. (FIFO) (FIFO) #1 TXRTSPOL Transmitter request-to-send polarity 2 1 read-write 0 Transmitter RTS is active low. #0 1 Transmitter RTS is active high. #1 PFIFO UART FIFO Parameters 0x10 8 read-write n 0x0 0x0 RXFE Receive FIFO Enable 3 1 read-write 0 Receive FIFO is not enabled. Buffer is depth 1. (Legacy support) #0 1 Receive FIFO is enabled. Buffer is depth indicted by RXFIFOSIZE. #1 RXFIFOSIZE Receive FIFO. Buffer Depth 0 3 read-only 000 Receive FIFO/Buffer depth = 1 dataword. #000 001 Receive FIFO/Buffer depth = 4 datawords. #001 010 Receive FIFO/Buffer depth = 8 datawords. #010 011 Receive FIFO/Buffer depth = 16 datawords. #011 100 Receive FIFO/Buffer depth = 32 datawords. #100 101 Receive FIFO/Buffer depth = 64 datawords. #101 110 Receive FIFO/Buffer depth = 128 datawords. #110 TXFE Transmit FIFO Enable 7 1 read-write 0 Transmit FIFO is not enabled. Buffer is depth 1. (Legacy support). #0 1 Transmit FIFO is enabled. Buffer is depth indicated by TXFIFOSIZE. #1 TXFIFOSIZE Transmit FIFO. Buffer Depth 4 3 read-only 000 Transmit FIFO/Buffer depth = 1 dataword. #000 001 Transmit FIFO/Buffer depth = 4 datawords. #001 010 Transmit FIFO/Buffer depth = 8 datawords. #010 011 Transmit FIFO/Buffer depth = 16 datawords. #011 100 Transmit FIFO/Buffer depth = 32 datawords. #100 101 Transmit FIFO/Buffer depth = 64 datawords. #101 110 Transmit FIFO/Buffer depth = 128 datawords. #110 RCFIFO UART FIFO Receive Count 0x16 8 read-only n 0x0 0x0 RXCOUNT Receive Counter 0 8 read-only RWFIFO UART FIFO Receive Watermark 0x15 8 read-write n 0x0 0x0 RXWATER Receive Watermark 0 8 read-write S1 UART Status Register 1 0x4 8 read-only n 0x0 0x0 FE Framing Error Flag 1 1 read-only 0 No framing error detected. #0 1 Framing error. #1 IDLE Idle Line Flag 4 1 read-only 0 Receiver input is either active now or has never become active since the IDLE flag was last cleared. #0 1 Receiver input has become idle or the flag has not been cleared since it last asserted. #1 NF Noise Flag 2 1 read-only 0 No noise detected since the last time this flag was cleared. If the receive buffer has a depth greater than 1 then there may be data in the receiver buffer that was received with noise. #0 1 At least one dataword was received with noise detected since the last time the flag was cleared. #1 OR Receiver Overrun Flag 3 1 read-only 0 No overrun has occurred since the last time the flag was cleared. #0 1 Overrun has occurred or the overrun flag has not been cleared since the last overrun occurred. #1 PF Parity Error Flag 0 1 read-only 0 No parity error detected since the last time this flag was cleared. If the receive buffer has a depth greater than 1, then there may be data in the receive buffer what was received with a parity error. #0 1 At least one dataword was received with a parity error since the last time this flag was cleared. #1 RDRF Receive Data Register Full Flag 5 1 read-only 0 The number of datawords in the receive buffer is less than the number indicated by RXWATER. #0 1 The number of datawords in the receive buffer is equal to or greater than the number indicated by RXWATER at some point in time since this flag was last cleared. #1 TC Transmit Complete Flag 6 1 read-only 0 Transmitter active (sending data, a preamble, or a break). #0 1 Transmitter idle (transmission activity complete). #1 TDRE Transmit Data Register Empty Flag 7 1 read-only 0 The amount of data in the transmit buffer is greater than the value indicated by TWFIFO[TXWATER]. #0 1 The amount of data in the transmit buffer is less than or equal to the value indicated by TWFIFO[TXWATER] at some point in time since the flag has been cleared. #1 S2 UART Status Register 2 0x5 8 read-write n 0x0 0x0 BRK13 Break Transmit Character Length 2 1 read-write 0 Break character is 10, 11, or 12 bits long. #0 1 Break character is 13 or 14 bits long. #1 LBKDE LIN Break Detection Enable 1 1 read-write 0 Break character detection is disabled. #0 1 Break character is detected at length of 11 bit times if C1[M] = 0 or 12 bits time if C1[M] = 1. #1 LBKDIF LIN Break Detect Interrupt Flag 7 1 read-write 0 No LIN break character detected. #0 1 LIN break character detected. #1 MSBF Most Significant Bit First 5 1 read-write 0 LSB (bit0) is the first bit that is transmitted following the start bit. Further, the first bit received after the start bit is identified as bit0. #0 1 MSB (bit8, bit7 or bit6) is the first bit that is transmitted following the start bit, depending on the setting of C1[M] and C1[PE]. Further, the first bit received after the start bit is identified as bit8, bit7, or bit6, depending on the setting of C1[M] and C1[PE]. #1 RAF Receiver Active Flag 0 1 read-only 0 UART receiver idle/inactive waiting for a start bit. #0 1 UART receiver active, RxD input not idle. #1 RWUID Receive Wakeup Idle Detect 3 1 read-write 0 S1[IDLE] is not set upon detection of an idle character. #0 1 S1[IDLE] is set upon detection of an idle character. #1 RXEDGIF RxD Pin Active Edge Interrupt Flag 6 1 read-write 0 No active edge on the receive pin has occurred. #0 1 An active edge on the receive pin has occurred. #1 RXINV Receive Data Inversion 4 1 read-write 0 Receive data is not inverted. #0 1 Receive data is inverted. #1 SFIFO UART FIFO Status Register 0x12 8 read-write n 0x0 0x0 RXEMPT Receive Buffer/FIFO Empty 6 1 read-only 0 Receive buffer is not empty. #0 1 Receive buffer is empty. #1 RXOF Receiver Buffer Overflow Flag 2 1 read-write 0 No receive buffer overflow has occurred since the last time the flag was cleared. #0 1 At least one receive buffer overflow has occurred since the last time the flag was cleared. #1 RXUF Receiver Buffer Underflow Flag 0 1 read-write 0 No receive buffer underflow has occurred since the last time the flag was cleared. #0 1 At least one receive buffer underflow has occurred since the last time the flag was cleared. #1 TXEMPT Transmit Buffer/FIFO Empty 7 1 read-only 0 Transmit buffer is not empty. #0 1 Transmit buffer is empty. #1 TXOF Transmitter Buffer Overflow Flag 1 1 read-write 0 No transmit buffer overflow has occurred since the last time the flag was cleared. #0 1 At least one transmit buffer overflow has occurred since the last time the flag was cleared. #1 TCFIFO UART FIFO Transmit Count 0x14 8 read-only n 0x0 0x0 TXCOUNT Transmit Counter 0 8 read-only TWFIFO UART FIFO Transmit Watermark 0x13 8 read-write n 0x0 0x0 TXWATER Transmit Watermark 0 8 read-write UART2 Serial Communication Interface UART 0x0 0x0 0x17 registers n UART2_RX_TX 35 UART2_ERR 36 BDH UART Baud Rate Registers: High 0x0 8 read-write n 0x0 0x0 LBKDIE LIN Break Detect Interrupt Enable 7 1 read-write 0 LBKDIF interrupt requests disabled. #0 1 LBKDIF interrupt requests enabled. #1 RXEDGIE RxD Input Active Edge Interrupt Enable 6 1 read-write 0 Hardware interrupts from RXEDGIF disabled using polling. #0 1 RXEDGIF interrupt request enabled. #1 SBR UART Baud Rate Bits 0 5 read-write BDL UART Baud Rate Registers: Low 0x1 8 read-write n 0x0 0x0 SBR UART Baud Rate Bits 0 8 read-write C1 UART Control Register 1 0x2 8 read-write n 0x0 0x0 ILT Idle Line Type Select 2 1 read-write 0 Idle character bit count starts after start bit. #0 1 Idle character bit count starts after stop bit. #1 LOOPS Loop Mode Select 7 1 read-write 0 Normal operation. #0 1 Loop mode where transmitter output is internally connected to receiver input. The receiver input is determined by RSRC. #1 M 9-bit or 8-bit Mode Select 4 1 read-write 0 Normal-start + 8 data bits (MSB/LSB first as determined by MSBF) + stop. #0 1 Use-start + 9 data bits (MSB/LSB first as determined by MSBF) + stop. #1 PE Parity Enable 1 1 read-write 0 Parity function disabled. #0 1 Parity function enabled. #1 PT Parity Type 0 1 read-write 0 Even parity. #0 1 Odd parity. #1 RSRC Receiver Source Select 5 1 read-write 0 Selects internal loop back mode. The receiver input is internally connected to transmitter output. #0 1 Single wire UART mode where the receiver input is connected to the transmit pin input signal. #1 UARTSWAI UART Stops in Wait Mode 6 1 read-write 0 UART clock continues to run in Wait mode. #0 1 UART clock freezes while CPU is in Wait mode. #1 WAKE Receiver Wakeup Method Select 3 1 read-write 0 Idle line wakeup. #0 1 Address mark wakeup. #1 C2 UART Control Register 2 0x3 8 read-write n 0x0 0x0 ILIE Idle Line Interrupt Enable 4 1 read-write 0 IDLE interrupt requests disabled. #0 1 IDLE interrupt requests enabled. #1 RE Receiver Enable 2 1 read-write 0 Receiver off. #0 1 Receiver on. #1 RIE Receiver Full Interrupt or DMA Transfer Enable 5 1 read-write 0 RDRF interrupt and DMA transfer requests disabled. #0 1 RDRF interrupt or DMA transfer requests enabled. #1 RWU Receiver Wakeup Control 1 1 read-write 0 Normal operation. #0 1 RWU enables the wakeup function and inhibits further receiver interrupt requests. Normally, hardware wakes the receiver by automatically clearing RWU. #1 SBK Send Break 0 1 read-write 0 Normal transmitter operation. #0 1 Queue break characters to be sent. #1 TCIE Transmission Complete Interrupt Enable 6 1 read-write 0 TC interrupt requests disabled. #0 1 TC interrupt requests enabled. #1 TE Transmitter Enable 3 1 read-write 0 Transmitter off. #0 1 Transmitter on. #1 TIE Transmitter Interrupt or DMA Transfer Enable. 7 1 read-write 0 TDRE interrupt and DMA transfer requests disabled. #0 1 TDRE interrupt or DMA transfer requests enabled. #1 C3 UART Control Register 3 0x6 8 read-write n 0x0 0x0 FEIE Framing Error Interrupt Enable 1 1 read-write 0 FE interrupt requests are disabled. #0 1 FE interrupt requests are enabled. #1 NEIE Noise Error Interrupt Enable 2 1 read-write 0 NF interrupt requests are disabled. #0 1 NF interrupt requests are enabled. #1 ORIE Overrun Error Interrupt Enable 3 1 read-write 0 OR interrupts are disabled. #0 1 OR interrupt requests are enabled. #1 PEIE Parity Error Interrupt Enable 0 1 read-write 0 PF interrupt requests are disabled. #0 1 PF interrupt requests are enabled. #1 R8 Received Bit 8 7 1 read-only T8 Transmit Bit 8 6 1 read-write TXDIR Transmitter Pin Data Direction in Single-Wire mode 5 1 read-write 0 TXD pin is an input in single wire mode. #0 1 TXD pin is an output in single wire mode. #1 TXINV Transmit Data Inversion. 4 1 read-write 0 Transmit data is not inverted. #0 1 Transmit data is inverted. #1 C4 UART Control Register 4 0xA 8 read-write n 0x0 0x0 BRFA Baud Rate Fine Adjust 0 5 read-write M10 10-bit Mode select 5 1 read-write 0 The parity bit is the ninth bit in the serial transmission. #0 1 The parity bit is the tenth bit in the serial transmission. #1 MAEN1 Match Address Mode Enable 1 7 1 read-write 0 All data received is transferred to the data buffer if MAEN2 is cleared. #0 1 All data received with the most significant bit cleared, is discarded. All data received with the most significant bit set, is compared with contents of MA1 register. If no match occurs, the data is discarded. If match occurs, data is transferred to the data buffer. This field must be cleared when C7816[ISO7816E] is set/enabled. #1 MAEN2 Match Address Mode Enable 2 6 1 read-write 0 All data received is transferred to the data buffer if MAEN1 is cleared. #0 1 All data received with the most significant bit cleared, is discarded. All data received with the most significant bit set, is compared with contents of MA2 register. If no match occurs, the data is discarded. If a match occurs, data is transferred to the data buffer. This field must be cleared when C7816[ISO7816E] is set/enabled. #1 C5 UART Control Register 5 0xB 8 read-write n 0x0 0x0 RDMAS Receiver Full DMA Select 5 1 read-write 0 If C2[RIE] and S1[RDRF] are set, the RDFR interrupt request signal is asserted to request an interrupt service. #0 1 If C2[RIE] and S1[RDRF] are set, the RDRF DMA request signal is asserted to request a DMA transfer. #1 TDMAS Transmitter DMA Select 7 1 read-write 0 If C2[TIE] is set and the S1[TDRE] flag is set, the TDRE interrupt request signal is asserted to request interrupt service. #0 1 If C2[TIE] is set and the S1[TDRE] flag is set, the TDRE DMA request signal is asserted to request a DMA transfer. #1 CFIFO UART FIFO Control Register 0x11 8 read-write n 0x0 0x0 RXFLUSH Receive FIFO/Buffer Flush 6 1 write-only 0 No flush operation occurs. #0 1 All data in the receive FIFO/buffer is cleared out. #1 RXOFE Receive FIFO Overflow Interrupt Enable 2 1 read-write 0 RXOF flag does not generate an interrupt to the host. #0 1 RXOF flag generates an interrupt to the host. #1 RXUFE Receive FIFO Underflow Interrupt Enable 0 1 read-write 0 RXUF flag does not generate an interrupt to the host. #0 1 RXUF flag generates an interrupt to the host. #1 TXFLUSH Transmit FIFO/Buffer Flush 7 1 write-only 0 No flush operation occurs. #0 1 All data in the transmit FIFO/Buffer is cleared out. #1 TXOFE Transmit FIFO Overflow Interrupt Enable 1 1 read-write 0 TXOF flag does not generate an interrupt to the host. #0 1 TXOF flag generates an interrupt to the host. #1 D UART Data Register 0x7 8 read-write n 0x0 0x0 RT Reads return the contents of the read-only receive data register and writes go to the write-only transmit data register 0 8 read-write ED UART Extended Data Register 0xC 8 read-only n 0x0 0x0 NOISY The current received dataword contained in D and C3[R8] was received with noise. 7 1 read-only 0 The dataword was received without noise. #0 1 The data was received with noise. #1 PARITYE The current received dataword contained in D and C3[R8] was received with a parity error. 6 1 read-only 0 The dataword was received without a parity error. #0 1 The dataword was received with a parity error. #1 IR UART Infrared Register 0xE 8 read-write n 0x0 0x0 IREN Infrared enable 2 1 read-write 0 IR disabled. #0 1 IR enabled. #1 TNP Transmitter narrow pulse 0 2 read-write 00 3/16. #00 01 1/16. #01 10 1/32. #10 11 1/4. #11 MA1 UART Match Address Registers 1 0x8 8 read-write n 0x0 0x0 MA Match Address 0 8 read-write MA2 UART Match Address Registers 2 0x9 8 read-write n 0x0 0x0 MA Match Address 0 8 read-write MODEM UART Modem Register 0xD 8 read-write n 0x0 0x0 RXRTSE Receiver request-to-send enable 3 1 read-write 0 The receiver has no effect on RTS. #0 1 RTS is deasserted if the number of characters in the receiver data register (FIFO) is equal to or greater than RWFIFO[RXWATER]. RTS is asserted when the number of characters in the receiver data register (FIFO) is less than RWFIFO[RXWATER]. #1 TXCTSE Transmitter clear-to-send enable 0 1 read-write 0 CTS has no effect on the transmitter. #0 1 Enables clear-to-send operation. The transmitter checks the state of CTS each time it is ready to send a character. If CTS is asserted, the character is sent. If CTS is deasserted, the signal TXD remains in the mark state and transmission is delayed until CTS is asserted. Changes in CTS as a character is being sent do not affect its transmission. #1 TXRTSE Transmitter request-to-send enable 1 1 read-write 0 The transmitter has no effect on RTS. #0 1 When a character is placed into an empty transmitter data buffer , RTS asserts one bit time before the start bit is transmitted. RTS deasserts one bit time after all characters in the transmitter data buffer and shift register are completely sent, including the last stop bit. (FIFO) (FIFO) #1 TXRTSPOL Transmitter request-to-send polarity 2 1 read-write 0 Transmitter RTS is active low. #0 1 Transmitter RTS is active high. #1 PFIFO UART FIFO Parameters 0x10 8 read-write n 0x0 0x0 RXFE Receive FIFO Enable 3 1 read-write 0 Receive FIFO is not enabled. Buffer is depth 1. (Legacy support) #0 1 Receive FIFO is enabled. Buffer is depth indicted by RXFIFOSIZE. #1 RXFIFOSIZE Receive FIFO. Buffer Depth 0 3 read-only 000 Receive FIFO/Buffer depth = 1 dataword. #000 001 Receive FIFO/Buffer depth = 4 datawords. #001 010 Receive FIFO/Buffer depth = 8 datawords. #010 011 Receive FIFO/Buffer depth = 16 datawords. #011 100 Receive FIFO/Buffer depth = 32 datawords. #100 101 Receive FIFO/Buffer depth = 64 datawords. #101 110 Receive FIFO/Buffer depth = 128 datawords. #110 TXFE Transmit FIFO Enable 7 1 read-write 0 Transmit FIFO is not enabled. Buffer is depth 1. (Legacy support). #0 1 Transmit FIFO is enabled. Buffer is depth indicated by TXFIFOSIZE. #1 TXFIFOSIZE Transmit FIFO. Buffer Depth 4 3 read-only 000 Transmit FIFO/Buffer depth = 1 dataword. #000 001 Transmit FIFO/Buffer depth = 4 datawords. #001 010 Transmit FIFO/Buffer depth = 8 datawords. #010 011 Transmit FIFO/Buffer depth = 16 datawords. #011 100 Transmit FIFO/Buffer depth = 32 datawords. #100 101 Transmit FIFO/Buffer depth = 64 datawords. #101 110 Transmit FIFO/Buffer depth = 128 datawords. #110 RCFIFO UART FIFO Receive Count 0x16 8 read-only n 0x0 0x0 RXCOUNT Receive Counter 0 8 read-only RWFIFO UART FIFO Receive Watermark 0x15 8 read-write n 0x0 0x0 RXWATER Receive Watermark 0 8 read-write S1 UART Status Register 1 0x4 8 read-only n 0x0 0x0 FE Framing Error Flag 1 1 read-only 0 No framing error detected. #0 1 Framing error. #1 IDLE Idle Line Flag 4 1 read-only 0 Receiver input is either active now or has never become active since the IDLE flag was last cleared. #0 1 Receiver input has become idle or the flag has not been cleared since it last asserted. #1 NF Noise Flag 2 1 read-only 0 No noise detected since the last time this flag was cleared. If the receive buffer has a depth greater than 1 then there may be data in the receiver buffer that was received with noise. #0 1 At least one dataword was received with noise detected since the last time the flag was cleared. #1 OR Receiver Overrun Flag 3 1 read-only 0 No overrun has occurred since the last time the flag was cleared. #0 1 Overrun has occurred or the overrun flag has not been cleared since the last overrun occurred. #1 PF Parity Error Flag 0 1 read-only 0 No parity error detected since the last time this flag was cleared. If the receive buffer has a depth greater than 1, then there may be data in the receive buffer what was received with a parity error. #0 1 At least one dataword was received with a parity error since the last time this flag was cleared. #1 RDRF Receive Data Register Full Flag 5 1 read-only 0 The number of datawords in the receive buffer is less than the number indicated by RXWATER. #0 1 The number of datawords in the receive buffer is equal to or greater than the number indicated by RXWATER at some point in time since this flag was last cleared. #1 TC Transmit Complete Flag 6 1 read-only 0 Transmitter active (sending data, a preamble, or a break). #0 1 Transmitter idle (transmission activity complete). #1 TDRE Transmit Data Register Empty Flag 7 1 read-only 0 The amount of data in the transmit buffer is greater than the value indicated by TWFIFO[TXWATER]. #0 1 The amount of data in the transmit buffer is less than or equal to the value indicated by TWFIFO[TXWATER] at some point in time since the flag has been cleared. #1 S2 UART Status Register 2 0x5 8 read-write n 0x0 0x0 BRK13 Break Transmit Character Length 2 1 read-write 0 Break character is 10, 11, or 12 bits long. #0 1 Break character is 13 or 14 bits long. #1 LBKDE LIN Break Detection Enable 1 1 read-write 0 Break character detection is disabled. #0 1 Break character is detected at length of 11 bit times if C1[M] = 0 or 12 bits time if C1[M] = 1. #1 LBKDIF LIN Break Detect Interrupt Flag 7 1 read-write 0 No LIN break character detected. #0 1 LIN break character detected. #1 MSBF Most Significant Bit First 5 1 read-write 0 LSB (bit0) is the first bit that is transmitted following the start bit. Further, the first bit received after the start bit is identified as bit0. #0 1 MSB (bit8, bit7 or bit6) is the first bit that is transmitted following the start bit, depending on the setting of C1[M] and C1[PE]. Further, the first bit received after the start bit is identified as bit8, bit7, or bit6, depending on the setting of C1[M] and C1[PE]. #1 RAF Receiver Active Flag 0 1 read-only 0 UART receiver idle/inactive waiting for a start bit. #0 1 UART receiver active, RxD input not idle. #1 RWUID Receive Wakeup Idle Detect 3 1 read-write 0 S1[IDLE] is not set upon detection of an idle character. #0 1 S1[IDLE] is set upon detection of an idle character. #1 RXEDGIF RxD Pin Active Edge Interrupt Flag 6 1 read-write 0 No active edge on the receive pin has occurred. #0 1 An active edge on the receive pin has occurred. #1 RXINV Receive Data Inversion 4 1 read-write 0 Receive data is not inverted. #0 1 Receive data is inverted. #1 SFIFO UART FIFO Status Register 0x12 8 read-write n 0x0 0x0 RXEMPT Receive Buffer/FIFO Empty 6 1 read-only 0 Receive buffer is not empty. #0 1 Receive buffer is empty. #1 RXOF Receiver Buffer Overflow Flag 2 1 read-write 0 No receive buffer overflow has occurred since the last time the flag was cleared. #0 1 At least one receive buffer overflow has occurred since the last time the flag was cleared. #1 RXUF Receiver Buffer Underflow Flag 0 1 read-write 0 No receive buffer underflow has occurred since the last time the flag was cleared. #0 1 At least one receive buffer underflow has occurred since the last time the flag was cleared. #1 TXEMPT Transmit Buffer/FIFO Empty 7 1 read-only 0 Transmit buffer is not empty. #0 1 Transmit buffer is empty. #1 TXOF Transmitter Buffer Overflow Flag 1 1 read-write 0 No transmit buffer overflow has occurred since the last time the flag was cleared. #0 1 At least one transmit buffer overflow has occurred since the last time the flag was cleared. #1 TCFIFO UART FIFO Transmit Count 0x14 8 read-only n 0x0 0x0 TXCOUNT Transmit Counter 0 8 read-only TWFIFO UART FIFO Transmit Watermark 0x13 8 read-write n 0x0 0x0 TXWATER Transmit Watermark 0 8 read-write USB0 Universal Serial Bus, OTG Capable Controller USB0 0x0 0x0 0x15D registers n USB0 53 ADDINFO Peripheral Additional Info register 0xC 8 read-only n 0x0 0x0 IEHOST This bit is set if host mode is enabled. 0 1 read-only ADDR Address register 0x98 8 read-write n 0x0 0x0 ADDR USB Address 0 7 read-write LSEN Low Speed Enable bit 7 1 read-write BDTPAGE1 BDT Page register 1 0x9C 8 read-write n 0x0 0x0 BDTBA Provides address bits 15 through 9 of the BDT base address. 1 7 read-write BDTPAGE2 BDT Page Register 2 0xB0 8 read-write n 0x0 0x0 BDTBA Provides address bits 23 through 16 of the BDT base address that defines the location of Buffer Descriptor Table resides in system memory 0 8 read-write BDTPAGE3 BDT Page Register 3 0xB4 8 read-write n 0x0 0x0 BDTBA Provides address bits 31 through 24 of the BDT base address that defines the location of Buffer Descriptor Table resides in system memory 0 8 read-write CLK_RECOVER_CTRL USB Clock recovery control 0x140 8 read-write n 0x0 0x0 CLOCK_RECOVER_EN Crystal-less USB enable 7 1 read-write 0 Disable clock recovery block (default) #0 1 Enable clock recovery block #1 RESET_RESUME_ROUGH_EN Reset/resume to rough phase enable 6 1 read-write 0 Always works in tracking phase after the 1st time rough to track transition (default) #0 1 Go back to rough stage whenever bus reset or bus resume occurs #1 RESTART_IFRTRIM_EN Restart from IFR trim value 5 1 read-write 0 Trim fine adjustment always works based on the previous updated trim fine value (default) #0 1 Trim fine restarts from the IFR trim value whenever bus_reset/bus_resume is detected or module enable is desasserted #1 CLK_RECOVER_INT_STATUS Clock recovery separated interrupt status 0x15C 8 read-write n 0x0 0x0 OVF_ERROR Indicates that the USB clock recovery algorithm has detected that the frequency trim adjustment needed for the IRC48M output clock is outside the available TRIM_FINE adjustment range for the IRC48M module 4 1 read-write 0 No interrupt is reported #0 1 Unmasked interrupt has been generated #1 CLK_RECOVER_IRC_EN IRC48M oscillator enable register 0x144 8 read-write n 0x0 0x0 IRC_EN IRC48M enable 1 1 read-write 0 Disable the IRC48M module (default) #0 1 Enable the IRC48M module #1 REG_EN IRC48M regulator enable 0 1 read-write 0 IRC48M local regulator is disabled #0 1 IRC48M local regulator is enabled (default) #1 CONTROL USB OTG Control register 0x108 8 read-write n 0x0 0x0 DPPULLUPNONOTG Provides control of the DP Pullup in USBOTG, if USB is configured in non-OTG device mode. 4 1 read-write 0 DP Pullup in non-OTG device mode is not enabled. #0 1 DP Pullup in non-OTG device mode is enabled. #1 CTL Control register 0x94 8 read-write n 0x0 0x0 HOSTMODEEN When set to 1, this bit enables the USB Module to operate in Host mode 3 1 read-write JSTATE Live USB differential receiver JSTATE signal 7 1 read-write ODDRST Setting this bit to 1 resets all the BDT ODD ping/pong fields to 0, which then specifies the EVEN BDT bank 1 1 read-write RESET Setting this bit enables the USB Module to generate USB reset signaling 4 1 read-write RESUME When set to 1 this bit enables the USB Module to execute resume signaling 2 1 read-write SE0 Live USB Single Ended Zero signal 6 1 read-write TXSUSPENDTOKENBUSY In Host mode, TOKEN_BUSY is set when the USB module is busy executing a USB token 5 1 read-write USBENSOFEN USB Enable 0 1 read-write 0 Disables the USB Module. #0 1 Enables the USB Module. #1 ENDPT0 Endpoint Control register 0x180 8 read-write n 0x0 0x0 EPCTLDIS This bit, when set, disables control (SETUP) transfers 4 1 read-write EPHSHK When set this bit enables an endpoint to perform handshaking during a transaction to this endpoint 0 1 read-write EPRXEN This bit, when set, enables the endpoint for RX transfers. 3 1 read-write EPSTALL When set this bit indicates that the endpoint is called 1 1 read-write EPTXEN This bit, when set, enables the endpoint for TX transfers. 2 1 read-write HOSTWOHUB This is a Host mode only field and is present in the control register for endpoint 0 (ENDPT0) only 7 1 read-write RETRYDIS This is a Host mode only bit and is present in the control register for endpoint 0 (ENDPT0) only 6 1 read-write ENDPT1 Endpoint Control register 0x244 8 read-write n 0x0 0x0 EPCTLDIS This bit, when set, disables control (SETUP) transfers 4 1 read-write EPHSHK When set this bit enables an endpoint to perform handshaking during a transaction to this endpoint 0 1 read-write EPRXEN This bit, when set, enables the endpoint for RX transfers. 3 1 read-write EPSTALL When set this bit indicates that the endpoint is called 1 1 read-write EPTXEN This bit, when set, enables the endpoint for TX transfers. 2 1 read-write HOSTWOHUB This is a Host mode only field and is present in the control register for endpoint 0 (ENDPT0) only 7 1 read-write RETRYDIS This is a Host mode only bit and is present in the control register for endpoint 0 (ENDPT0) only 6 1 read-write ENDPT10 Endpoint Control register 0x9DC 8 read-write n 0x0 0x0 EPCTLDIS This bit, when set, disables control (SETUP) transfers 4 1 read-write EPHSHK When set this bit enables an endpoint to perform handshaking during a transaction to this endpoint 0 1 read-write EPRXEN This bit, when set, enables the endpoint for RX transfers. 3 1 read-write EPSTALL When set this bit indicates that the endpoint is called 1 1 read-write EPTXEN This bit, when set, enables the endpoint for TX transfers. 2 1 read-write HOSTWOHUB This is a Host mode only field and is present in the control register for endpoint 0 (ENDPT0) only 7 1 read-write RETRYDIS This is a Host mode only bit and is present in the control register for endpoint 0 (ENDPT0) only 6 1 read-write ENDPT11 Endpoint Control register 0xAC8 8 read-write n 0x0 0x0 EPCTLDIS This bit, when set, disables control (SETUP) transfers 4 1 read-write EPHSHK When set this bit enables an endpoint to perform handshaking during a transaction to this endpoint 0 1 read-write EPRXEN This bit, when set, enables the endpoint for RX transfers. 3 1 read-write EPSTALL When set this bit indicates that the endpoint is called 1 1 read-write EPTXEN This bit, when set, enables the endpoint for TX transfers. 2 1 read-write HOSTWOHUB This is a Host mode only field and is present in the control register for endpoint 0 (ENDPT0) only 7 1 read-write RETRYDIS This is a Host mode only bit and is present in the control register for endpoint 0 (ENDPT0) only 6 1 read-write ENDPT12 Endpoint Control register 0xBB8 8 read-write n 0x0 0x0 EPCTLDIS This bit, when set, disables control (SETUP) transfers 4 1 read-write EPHSHK When set this bit enables an endpoint to perform handshaking during a transaction to this endpoint 0 1 read-write EPRXEN This bit, when set, enables the endpoint for RX transfers. 3 1 read-write EPSTALL When set this bit indicates that the endpoint is called 1 1 read-write EPTXEN This bit, when set, enables the endpoint for TX transfers. 2 1 read-write HOSTWOHUB This is a Host mode only field and is present in the control register for endpoint 0 (ENDPT0) only 7 1 read-write RETRYDIS This is a Host mode only bit and is present in the control register for endpoint 0 (ENDPT0) only 6 1 read-write ENDPT13 Endpoint Control register 0xCAC 8 read-write n 0x0 0x0 EPCTLDIS This bit, when set, disables control (SETUP) transfers 4 1 read-write EPHSHK When set this bit enables an endpoint to perform handshaking during a transaction to this endpoint 0 1 read-write EPRXEN This bit, when set, enables the endpoint for RX transfers. 3 1 read-write EPSTALL When set this bit indicates that the endpoint is called 1 1 read-write EPTXEN This bit, when set, enables the endpoint for TX transfers. 2 1 read-write HOSTWOHUB This is a Host mode only field and is present in the control register for endpoint 0 (ENDPT0) only 7 1 read-write RETRYDIS This is a Host mode only bit and is present in the control register for endpoint 0 (ENDPT0) only 6 1 read-write ENDPT14 Endpoint Control register 0xDA4 8 read-write n 0x0 0x0 EPCTLDIS This bit, when set, disables control (SETUP) transfers 4 1 read-write EPHSHK When set this bit enables an endpoint to perform handshaking during a transaction to this endpoint 0 1 read-write EPRXEN This bit, when set, enables the endpoint for RX transfers. 3 1 read-write EPSTALL When set this bit indicates that the endpoint is called 1 1 read-write EPTXEN This bit, when set, enables the endpoint for TX transfers. 2 1 read-write HOSTWOHUB This is a Host mode only field and is present in the control register for endpoint 0 (ENDPT0) only 7 1 read-write RETRYDIS This is a Host mode only bit and is present in the control register for endpoint 0 (ENDPT0) only 6 1 read-write ENDPT15 Endpoint Control register 0xEA0 8 read-write n 0x0 0x0 EPCTLDIS This bit, when set, disables control (SETUP) transfers 4 1 read-write EPHSHK When set this bit enables an endpoint to perform handshaking during a transaction to this endpoint 0 1 read-write EPRXEN This bit, when set, enables the endpoint for RX transfers. 3 1 read-write EPSTALL When set this bit indicates that the endpoint is called 1 1 read-write EPTXEN This bit, when set, enables the endpoint for TX transfers. 2 1 read-write HOSTWOHUB This is a Host mode only field and is present in the control register for endpoint 0 (ENDPT0) only 7 1 read-write RETRYDIS This is a Host mode only bit and is present in the control register for endpoint 0 (ENDPT0) only 6 1 read-write ENDPT2 Endpoint Control register 0x30C 8 read-write n 0x0 0x0 EPCTLDIS This bit, when set, disables control (SETUP) transfers 4 1 read-write EPHSHK When set this bit enables an endpoint to perform handshaking during a transaction to this endpoint 0 1 read-write EPRXEN This bit, when set, enables the endpoint for RX transfers. 3 1 read-write EPSTALL When set this bit indicates that the endpoint is called 1 1 read-write EPTXEN This bit, when set, enables the endpoint for TX transfers. 2 1 read-write HOSTWOHUB This is a Host mode only field and is present in the control register for endpoint 0 (ENDPT0) only 7 1 read-write RETRYDIS This is a Host mode only bit and is present in the control register for endpoint 0 (ENDPT0) only 6 1 read-write ENDPT3 Endpoint Control register 0x3D8 8 read-write n 0x0 0x0 EPCTLDIS This bit, when set, disables control (SETUP) transfers 4 1 read-write EPHSHK When set this bit enables an endpoint to perform handshaking during a transaction to this endpoint 0 1 read-write EPRXEN This bit, when set, enables the endpoint for RX transfers. 3 1 read-write EPSTALL When set this bit indicates that the endpoint is called 1 1 read-write EPTXEN This bit, when set, enables the endpoint for TX transfers. 2 1 read-write HOSTWOHUB This is a Host mode only field and is present in the control register for endpoint 0 (ENDPT0) only 7 1 read-write RETRYDIS This is a Host mode only bit and is present in the control register for endpoint 0 (ENDPT0) only 6 1 read-write ENDPT4 Endpoint Control register 0x4A8 8 read-write n 0x0 0x0 EPCTLDIS This bit, when set, disables control (SETUP) transfers 4 1 read-write EPHSHK When set this bit enables an endpoint to perform handshaking during a transaction to this endpoint 0 1 read-write EPRXEN This bit, when set, enables the endpoint for RX transfers. 3 1 read-write EPSTALL When set this bit indicates that the endpoint is called 1 1 read-write EPTXEN This bit, when set, enables the endpoint for TX transfers. 2 1 read-write HOSTWOHUB This is a Host mode only field and is present in the control register for endpoint 0 (ENDPT0) only 7 1 read-write RETRYDIS This is a Host mode only bit and is present in the control register for endpoint 0 (ENDPT0) only 6 1 read-write ENDPT5 Endpoint Control register 0x57C 8 read-write n 0x0 0x0 EPCTLDIS This bit, when set, disables control (SETUP) transfers 4 1 read-write EPHSHK When set this bit enables an endpoint to perform handshaking during a transaction to this endpoint 0 1 read-write EPRXEN This bit, when set, enables the endpoint for RX transfers. 3 1 read-write EPSTALL When set this bit indicates that the endpoint is called 1 1 read-write EPTXEN This bit, when set, enables the endpoint for TX transfers. 2 1 read-write HOSTWOHUB This is a Host mode only field and is present in the control register for endpoint 0 (ENDPT0) only 7 1 read-write RETRYDIS This is a Host mode only bit and is present in the control register for endpoint 0 (ENDPT0) only 6 1 read-write ENDPT6 Endpoint Control register 0x654 8 read-write n 0x0 0x0 EPCTLDIS This bit, when set, disables control (SETUP) transfers 4 1 read-write EPHSHK When set this bit enables an endpoint to perform handshaking during a transaction to this endpoint 0 1 read-write EPRXEN This bit, when set, enables the endpoint for RX transfers. 3 1 read-write EPSTALL When set this bit indicates that the endpoint is called 1 1 read-write EPTXEN This bit, when set, enables the endpoint for TX transfers. 2 1 read-write HOSTWOHUB This is a Host mode only field and is present in the control register for endpoint 0 (ENDPT0) only 7 1 read-write RETRYDIS This is a Host mode only bit and is present in the control register for endpoint 0 (ENDPT0) only 6 1 read-write ENDPT7 Endpoint Control register 0x730 8 read-write n 0x0 0x0 EPCTLDIS This bit, when set, disables control (SETUP) transfers 4 1 read-write EPHSHK When set this bit enables an endpoint to perform handshaking during a transaction to this endpoint 0 1 read-write EPRXEN This bit, when set, enables the endpoint for RX transfers. 3 1 read-write EPSTALL When set this bit indicates that the endpoint is called 1 1 read-write EPTXEN This bit, when set, enables the endpoint for TX transfers. 2 1 read-write HOSTWOHUB This is a Host mode only field and is present in the control register for endpoint 0 (ENDPT0) only 7 1 read-write RETRYDIS This is a Host mode only bit and is present in the control register for endpoint 0 (ENDPT0) only 6 1 read-write ENDPT8 Endpoint Control register 0x810 8 read-write n 0x0 0x0 EPCTLDIS This bit, when set, disables control (SETUP) transfers 4 1 read-write EPHSHK When set this bit enables an endpoint to perform handshaking during a transaction to this endpoint 0 1 read-write EPRXEN This bit, when set, enables the endpoint for RX transfers. 3 1 read-write EPSTALL When set this bit indicates that the endpoint is called 1 1 read-write EPTXEN This bit, when set, enables the endpoint for TX transfers. 2 1 read-write HOSTWOHUB This is a Host mode only field and is present in the control register for endpoint 0 (ENDPT0) only 7 1 read-write RETRYDIS This is a Host mode only bit and is present in the control register for endpoint 0 (ENDPT0) only 6 1 read-write ENDPT9 Endpoint Control register 0x8F4 8 read-write n 0x0 0x0 EPCTLDIS This bit, when set, disables control (SETUP) transfers 4 1 read-write EPHSHK When set this bit enables an endpoint to perform handshaking during a transaction to this endpoint 0 1 read-write EPRXEN This bit, when set, enables the endpoint for RX transfers. 3 1 read-write EPSTALL When set this bit indicates that the endpoint is called 1 1 read-write EPTXEN This bit, when set, enables the endpoint for TX transfers. 2 1 read-write HOSTWOHUB This is a Host mode only field and is present in the control register for endpoint 0 (ENDPT0) only 7 1 read-write RETRYDIS This is a Host mode only bit and is present in the control register for endpoint 0 (ENDPT0) only 6 1 read-write ERREN Error Interrupt Enable register 0x8C 8 read-write n 0x0 0x0 BTOERREN BTOERR Interrupt Enable 4 1 read-write 0 Disables the BTOERR interrupt. #0 1 Enables the BTOERR interrupt. #1 BTSERREN BTSERR Interrupt Enable 7 1 read-write 0 Disables the BTSERR interrupt. #0 1 Enables the BTSERR interrupt. #1 CRC16EN CRC16 Interrupt Enable 2 1 read-write 0 Disables the CRC16 interrupt. #0 1 Enables the CRC16 interrupt. #1 CRC5EOFEN CRC5/EOF Interrupt Enable 1 1 read-write 0 Disables the CRC5/EOF interrupt. #0 1 Enables the CRC5/EOF interrupt. #1 DFN8EN DFN8 Interrupt Enable 3 1 read-write 0 Disables the DFN8 interrupt. #0 1 Enables the DFN8 interrupt. #1 DMAERREN DMAERR Interrupt Enable 5 1 read-write 0 Disables the DMAERR interrupt. #0 1 Enables the DMAERR interrupt. #1 PIDERREN PIDERR Interrupt Enable 0 1 read-write 0 Disables the PIDERR interrupt. #0 1 Enters the PIDERR interrupt. #1 ERRSTAT Error Interrupt Status register 0x88 8 read-write n 0x0 0x0 BTOERR This bit is set when a bus turnaround timeout error occurs 4 1 read-write BTSERR This bit is set when a bit stuff error is detected 7 1 read-write CRC16 This bit is set when a data packet is rejected due to a CRC16 error. 2 1 read-write CRC5EOF This error interrupt has two functions 1 1 read-write DFN8 This bit is set if the data field received was not 8 bits in length 3 1 read-write DMAERR This bit is set if the USB Module has requested a DMA access to read a new BDT but has not been given the bus before it needs to receive or transmit data 5 1 read-write PIDERR This bit is set when the PID check field fails. 0 1 read-write FRMNUMH Frame Number register High 0xA4 8 read-write n 0x0 0x0 FRM This 3-bit field and the 8-bit field in the Frame Number Register Low are used to compute the address where the current Buffer Descriptor Table (BDT) resides in system memory 0 3 read-write FRMNUML Frame Number register Low 0xA0 8 read-write n 0x0 0x0 FRM This 8-bit field and the 3-bit field in the Frame Number Register High are used to compute the address where the current Buffer Descriptor Table (BDT) resides in system memory 0 8 read-write IDCOMP Peripheral ID Complement register 0x4 8 read-only n 0x0 0x0 NID Ones' complement of PERID[ID]. bits. 0 6 read-only INTEN Interrupt Enable register 0x84 8 read-write n 0x0 0x0 ATTACHEN ATTACH Interrupt Enable 6 1 read-write 0 Disables the ATTACH interrupt. #0 1 Enables the ATTACH interrupt. #1 ERROREN ERROR Interrupt Enable 1 1 read-write 0 Disables the ERROR interrupt. #0 1 Enables the ERROR interrupt. #1 RESUMEEN RESUME Interrupt Enable 5 1 read-write 0 Disables the RESUME interrupt. #0 1 Enables the RESUME interrupt. #1 SLEEPEN SLEEP Interrupt Enable 4 1 read-write 0 Disables the SLEEP interrupt. #0 1 Enables the SLEEP interrupt. #1 SOFTOKEN SOFTOK Interrupt Enable 2 1 read-write 0 Disbles the SOFTOK interrupt. #0 1 Enables the SOFTOK interrupt. #1 STALLEN STALL Interrupt Enable 7 1 read-write 0 Diasbles the STALL interrupt. #0 1 Enables the STALL interrupt. #1 TOKDNEEN TOKDNE Interrupt Enable 3 1 read-write 0 Disables the TOKDNE interrupt. #0 1 Enables the TOKDNE interrupt. #1 USBRSTEN USBRST Interrupt Enable 0 1 read-write 0 Disables the USBRST interrupt. #0 1 Enables the USBRST interrupt. #1 ISTAT Interrupt Status register 0x80 8 read-write n 0x0 0x0 ATTACH Attach Interrupt 6 1 read-write ERROR This bit is set when any of the error conditions within Error Interrupt Status (ERRSTAT) register occur 1 1 read-write RESUME This bit is set when a K-state is observed on the DP/DM signals for 2 5 1 read-write SLEEP This bit is set when the USB Module detects a constant idle on the USB bus for 3 ms 4 1 read-write SOFTOK This bit is set when the USB Module receives a Start Of Frame (SOF) token 2 1 read-write STALL Stall Interrupt 7 1 read-write TOKDNE This bit is set when the current token being processed has completed 3 1 read-write USBRST This bit is set when the USB Module has decoded a valid USB reset 0 1 read-write OBSERVE USB OTG Observe register 0x104 8 read-only n 0x0 0x0 DMPD Provides observability of the D- Pulldown enable at the USB transceiver. 4 1 read-only 0 D- pulldown disabled. #0 1 D- pulldown enabled. #1 DPPD Provides observability of the D+ Pulldown enable at the USB transceiver. 6 1 read-only 0 D+ pulldown disabled. #0 1 D+ pulldown enabled. #1 DPPU Provides observability of the D+ Pullup enable at the USB transceiver. 7 1 read-only 0 D+ pullup disabled. #0 1 D+ pullup enabled. #1 OTGCTL OTG Control register 0x1C 8 read-write n 0x0 0x0 DMLOW D- Data Line pull-down resistor enable 4 1 read-write 0 D- pulldown resistor is not enabled. #0 1 D- pulldown resistor is enabled. #1 DPHIGH D+ Data Line pullup resistor enable 7 1 read-write 0 D+ pullup resistor is not enabled #0 1 D+ pullup resistor is enabled #1 DPLOW D+ Data Line pull-down resistor enable 5 1 read-write 0 D+ pulldown resistor is not enabled. #0 1 D+ pulldown resistor is enabled. #1 OTGEN On-The-Go pullup/pulldown resistor enable 2 1 read-write 0 If USB_EN is 1 and HOST_MODE is 0 in the Control Register (CTL), then the D+ Data Line pull-up resistors are enabled. If HOST_MODE is 1 the D+ and D- Data Line pull-down resistors are engaged. #0 1 The pull-up and pull-down controls in this register are used. #1 OTGICR OTG Interrupt Control register 0x14 8 read-write n 0x0 0x0 AVBUSEN A VBUS Valid Interrupt Enable 0 1 read-write 0 Disables the AVBUSCHG interrupt. #0 1 Enables the AVBUSCHG interrupt. #1 BSESSEN B Session END Interrupt Enable 2 1 read-write 0 Disables the B_SESS_CHG interrupt. #0 1 Enables the B_SESS_CHG interrupt. #1 IDEN ID Interrupt Enable 7 1 read-write 0 The ID interrupt is disabled #0 1 The ID interrupt is enabled #1 LINESTATEEN Line State Change Interrupt Enable 5 1 read-write 0 Disables the LINE_STAT_CHG interrupt. #0 1 Enables the LINE_STAT_CHG interrupt. #1 ONEMSECEN One Millisecond Interrupt Enable 6 1 read-write 0 Diables the 1ms timer interrupt. #0 1 Enables the 1ms timer interrupt. #1 SESSVLDEN Session Valid Interrupt Enable 3 1 read-write 0 Disables the SESSVLDCHG interrupt. #0 1 Enables the SESSVLDCHG interrupt. #1 OTGISTAT OTG Interrupt Status register 0x10 8 read-write n 0x0 0x0 AVBUSCHG This bit is set when a change in VBUS is detected on an A device. 0 1 read-write B_SESS_CHG This bit is set when a change in VBUS is detected on a B device. 2 1 read-write IDCHG This bit is set when a change in the ID Signal from the USB connector is sensed. 7 1 read-write LINE_STATE_CHG This interrupt is set when the USB line state (CTL[SE0] and CTL[JSTATE] bits) are stable without change for 1 millisecond, and the value of the line state is different from the last time when the line state was stable 5 1 read-write ONEMSEC This bit is set when the 1 millisecond timer expires 6 1 read-write SESSVLDCHG This bit is set when a change in VBUS is detected indicating a session valid or a session no longer valid 3 1 read-write OTGSTAT OTG Status register 0x18 8 read-write n 0x0 0x0 AVBUSVLD A VBUS Valid 0 1 read-write 0 The VBUS voltage is below the A VBUS Valid threshold. #0 1 The VBUS voltage is above the A VBUS Valid threshold. #1 BSESSEND B Session End 2 1 read-write 0 The VBUS voltage is above the B session end threshold. #0 1 The VBUS voltage is below the B session end threshold. #1 ID Indicates the current state of the ID pin on the USB connector 7 1 read-write 0 Indicates a Type A cable is plugged into the USB connector. #0 1 Indicates no cable is attached or a Type B cable is plugged into the USB connector. #1 LINESTATESTABLE Indicates that the internal signals that control the LINE_STATE_CHG field of OTGISTAT are stable for at least 1 millisecond 5 1 read-write 0 The LINE_STAT_CHG bit is not yet stable. #0 1 The LINE_STAT_CHG bit has been debounced and is stable. #1 ONEMSECEN This bit is reserved for the 1ms count, but it is not useful to software. 6 1 read-write SESS_VLD Session Valid 3 1 read-write 0 The VBUS voltage is below the B session valid threshold #0 1 The VBUS voltage is above the B session valid threshold. #1 PERID Peripheral ID register 0x0 8 read-only n 0x0 0x0 ID Peripheral Identification 0 6 read-only REV Peripheral Revision register 0x8 8 read-only n 0x0 0x0 REV Revision 0 8 read-only SOFTHLD SOF Threshold register 0xAC 8 read-write n 0x0 0x0 CNT Represents the SOF count threshold in byte times. 0 8 read-write STAT Status register 0x90 8 read-only n 0x0 0x0 ENDP This four-bit field encodes the endpoint address that received or transmitted the previous token 4 4 read-only ODD This bit is set if the last buffer descriptor updated was in the odd bank of the BDT. 2 1 read-only TX Transmit Indicator 3 1 read-only 0 The most recent transaction was a receive operation. #0 1 The most recent transaction was a transmit operation. #1 TOKEN Token register 0xA8 8 read-write n 0x0 0x0 TOKENENDPT Holds the Endpoint address for the token command 0 4 read-write TOKENPID Contains the token type executed by the USB module. 4 4 read-write 0001 OUT Token. USB Module performs an OUT (TX) transaction. #0001 1001 IN Token. USB Module performs an In (RX) transaction. #1001 1101 SETUP Token. USB Module performs a SETUP (TX) transaction #1101 USBCTRL USB Control register 0x100 8 read-write n 0x0 0x0 PDE Enables the weak pulldowns on the USB transceiver. 6 1 read-write 0 Weak pulldowns are disabled on D+ and D-. #0 1 Weak pulldowns are enabled on D+ and D-. #1 SUSP Places the USB transceiver into the suspend state. 7 1 read-write 0 USB transceiver is not in suspend state. #0 1 USB transceiver is in suspend state. #1 USBFRMADJUST Frame Adjust Register 0x114 8 read-write n 0x0 0x0 ADJ Frame Adjustment 0 8 read-write USBTRC0 USB Transceiver Control register 0 0x10C 8 read-write n 0x0 0x0 SYNC_DET Synchronous USB Interrupt Detect 1 1 read-only 0 Synchronous interrupt has not been detected. #0 1 Synchronous interrupt has been detected. #1 USBRESET USB Reset 7 1 write-only 0 Normal USB module operation. #0 1 Returns the USB module to its reset state. #1 USBRESMEN Asynchronous Resume Interrupt Enable 5 1 read-write 0 USB asynchronous wakeup from suspend mode disabled. #0 1 USB asynchronous wakeup from suspend mode enabled. The asynchronous resume interrupt differs from the synchronous resume interrupt in that it asynchronously detects K-state using the unfiltered state of the D+ and D- pins. This interrupt should only be enabled when the Transceiver is suspended. #1 USB_CLK_RECOVERY_INT Combined USB Clock Recovery interrupt status 2 1 read-only USB_RESUME_INT USB Asynchronous Interrupt 0 1 read-only 0 No interrupt was generated. #0 1 Interrupt was generated because of the USB asynchronous interrupt. #1 VREF Voltage Reference VREF 0x0 0x0 0x2 registers n SC VREF Status and Control Register 0x1 8 read-write n 0x0 0x0 ICOMPEN Second order curvature compensation enable 5 1 read-write 0 Disabled #0 1 Enabled #1 MODE_LV Buffer Mode selection 0 2 read-write 00 Bandgap on only, for stabilization and startup #00 01 High power buffer mode enabled #01 10 Low-power buffer mode enabled #10 REGEN Regulator enable 6 1 read-write 0 Internal 1.75 V regulator is disabled. #0 1 Internal 1.75 V regulator is enabled. #1 VREFEN Internal Voltage Reference enable 7 1 read-write 0 The module is disabled. #0 1 The module is enabled. #1 VREFST Internal Voltage Reference stable 2 1 read-only 0 The module is disabled or not stable. #0 1 The module is stable. #1 TRM VREF Trim Register 0x0 8 read-write n 0x0 0x0 CHOPEN Chop oscillator enable. When set, internal chopping operation is enabled and the internal analog offset will be minimized. 6 1 read-write 0 Chop oscillator is disabled. #0 1 Chop oscillator is enabled. #1 TRIM Trim bits 0 6 read-write 000000 Min #0 111111 Max #111111 WDOG Generation 2008 Watchdog Timer WDOG 0x0 0x0 0x18 registers n WDOG_EWM 22 PRESC Watchdog Prescaler register 0x16 16 read-write n 0x0 0x0 PRESCVAL 3-bit prescaler for the watchdog clock source 8 3 read-write REFRESH Watchdog Refresh register 0xC 16 read-write n 0x0 0x0 WDOGREFRESH Watchdog refresh register 0 16 read-write RSTCNT Watchdog Reset Count register 0x14 16 read-write n 0x0 0x0 RSTCNT Counts the number of times the watchdog resets the system 0 16 read-write STCTRLH Watchdog Status and Control Register High 0x0 16 read-write n 0x0 0x0 ALLOWUPDATE Enables updates to watchdog write-once registers, after the reset-triggered initial configuration window (WCT) closes, through unlock sequence 4 1 read-write 0 No further updates allowed to WDOG write-once registers. #0 1 WDOG write-once registers can be unlocked for updating. #1 BYTESEL This 2-bit field selects the byte to be tested when the watchdog is in the byte test mode. 12 2 read-write 00 Byte 0 selected #00 01 Byte 1 selected #01 10 Byte 2 selected #10 11 Byte 3 selected #11 CLKSRC Selects clock source for the WDOG timer and other internal timing operations. 1 1 read-write 0 WDOG clock sourced from LPO . #0 1 WDOG clock sourced from alternate clock source. #1 DBGEN Enables or disables WDOG in Debug mode. 5 1 read-write 0 WDOG is disabled in CPU Debug mode. #0 1 WDOG is enabled in CPU Debug mode. #1 DISTESTWDOG Allows the WDOG's functional test mode to be disabled permanently 14 1 read-write 0 WDOG functional test mode is not disabled. #0 1 WDOG functional test mode is disabled permanently until reset. #1 IRQRSTEN Used to enable the debug breadcrumbs feature 2 1 read-write 0 WDOG time-out generates reset only. #0 1 WDOG time-out initially generates an interrupt. After WCT, it generates a reset. #1 STOPEN Enables or disables WDOG in Stop mode. 6 1 read-write 0 WDOG is disabled in CPU Stop mode. #0 1 WDOG is enabled in CPU Stop mode. #1 TESTSEL Effective only if TESTWDOG is set. Selects the test to be run on the watchdog timer. 11 1 read-write 0 Quick test. The timer runs in normal operation. You can load a small time-out value to do a quick test. #0 1 Byte test. Puts the timer in the byte test mode where individual bytes of the timer are enabled for operation and are compared for time-out against the corresponding byte of the programmed time-out value. Select the byte through BYTESEL[1:0] for testing. #1 TESTWDOG Puts the watchdog in the functional test mode 10 1 read-write WAITEN Enables or disables WDOG in Wait mode. 7 1 read-write 0 WDOG is disabled in CPU Wait mode. #0 1 WDOG is enabled in CPU Wait mode. #1 WDOGEN Enables or disables the WDOG's operation 0 1 read-write 0 WDOG is disabled. #0 1 WDOG is enabled. #1 WINEN Enables Windowing mode. 3 1 read-write 0 Windowing mode is disabled. #0 1 Windowing mode is enabled. #1 STCTRLL Watchdog Status and Control Register Low 0x2 16 read-write n 0x0 0x0 INTFLG Interrupt flag 15 1 read-write TMROUTH Watchdog Timer Output Register High 0x10 16 read-write n 0x0 0x0 TIMEROUTHIGH Shows the value of the upper 16 bits of the watchdog timer. 0 16 read-write TMROUTL Watchdog Timer Output Register Low 0x12 16 read-write n 0x0 0x0 TIMEROUTLOW Shows the value of the lower 16 bits of the watchdog timer. 0 16 read-write TOVALH Watchdog Time-out Value Register High 0x4 16 read-write n 0x0 0x0 TOVALHIGH Defines the upper 16 bits of the 32-bit time-out value for the watchdog timer 0 16 read-write TOVALL Watchdog Time-out Value Register Low 0x6 16 read-write n 0x0 0x0 TOVALLOW Defines the lower 16 bits of the 32-bit time-out value for the watchdog timer 0 16 read-write UNLOCK Watchdog Unlock register 0xE 16 read-write n 0x0 0x0 WDOGUNLOCK Writing the unlock sequence values to this register to makes the watchdog write-once registers writable again 0 16 read-write WINH Watchdog Window Register High 0x8 16 read-write n 0x0 0x0 WINHIGH Defines the upper 16 bits of the 32-bit window for the windowed mode of operation of the watchdog 0 16 read-write WINL Watchdog Window Register Low 0xA 16 read-write n 0x0 0x0 WINLOW Defines the lower 16 bits of the 32-bit window for the windowed mode of operation of the watchdog 0 16 read-write